Netgear WNDR3400v1

multiple revisions of this device, use caution

abgn (AN600)
N600 Wireless Dual Band Router
Support	Support page
Wikipedia	Netgear
InfoDepot Wiki	Netgear WNDR3400
WikiDevi.wi-cat.ru	Netgear WNDR3400v1
3rd Party Firmware
dd-wrt	Supported
OpenWrt	Supported
Tomato any flavor	Work in Progress
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Netgear WNDR3400 v1
Serial number prefix	2BK, 2BL, 2HT, 2PF, 2R7, 2R8, 2R9, 2RB, 2F0
FCC ID	PY309300116
IC ID	4054A-09300116
Board ID	U12H155T00
Type	wireless router
Series	WNDR3400
CPU1	Broadcom BCM4718A1
CPU1 Type	MIPS 74Kc
CPU1 Speed	480 MHz
Flash1 Chip	Macronix MX25L6405DMI-12G
Flash1 Size	8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> (Serial)
RAM1 Size	64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br />
RAM1 Chip	Samsung K4T51163QG-HCE6
nvram Size	64K
ETH chip1	Broadcom BCM4718A1
Switch	Broadcom BCM5325E
Ethernet Port Count	1-100MbE-WAN 4-100MbE-LAN
Wired Standard	IEEE 802.3/3u
802dot11 OUI: 20:4E:7F (17 E, 17 W), 30:46:9A (12 E, 15 W), E0:46:9A (14 E, 15 W), E0:91:F5 (12 E, 13 W) Ethernet OUI: 20:4E:7F (17 E, 17 W), 30:46:9A (12 E, 15 W), E0:46:9A (14 E, 15 W), E0:91:F5 (12 E, 13 W)
Stock bootloader	CFE 128kCFE
Stock FW OS	Linux 2.6.22
Expansion IF types	USB 2.0
USB ports	1
USB Hub Compatible	Untested
Power	12 VDC, 1.5 A
Connector type	barrel
Serial Port (UART)	yes
JTAG Port	yes
Flags: DFS
Other
Default SSID: NETGEAR (43 addl. devices) , NETGEAR-5G Default IP address: 192.168.1.1 the IP 192.168.1.1 is used by 1323 additional devices of which 107 are Netgear devices Default login user: admin Default login password: password admin:password credentials used by 425 additional devices of which 306 are Netgear devices
Manuf/OEM/ODM	Foxconn U12H155 T00
3rd Party Firmware Support	DD-WRT • (List) , FreshTomato • (List | DLs)
Retail
Availability	End of Life
FCC approval date	01 April 2010
(Est.) release date	01 September 2010
UPC	606449071146 (UPC DB, On eBay)
ASIN	B0041LYY6K ,  multiple uses
Country of manuf	China
Physical
LEDs/Color	Green/Amber/Blue
Dimensions	23 x 153 x 31 mm (8.8 x 6.0 x 1.2 in)
Radio 1
Chip1	Broadcom BCM4718A1
Wireless interface OUI	20:4E:7F, 30:46:9A, E0:46:9A, E0:91:F5
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio cor_rev	17
Radio Capabilities	ap sta wet led wme pio 802.11d 802.11h rm cqa mbss16 afterburner ampdu amsdurx amsdutx acktiming rxchain_pwrsave radio_pwrsave bcm_dcs
Radio 2
Chip1	Broadcom BCM43224
Wireless interface OUI	20:4E:7F, 30:46:9A, E0:46:9A, E0:91:F5
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
Radio cor_rev	23
Radio Capabilities	ap sta wet led wme pio 802.11d 802.11h rm cqa mbss16 afterburner ampdu amsdurx amsdutx acktiming rxchain_pwrsave radio_pwrsave bcm_dcs
FCC ID Netgear WNDR3300v2 PY309300116
CPU1 brand Radio1 chip1 brand Radio2 chip1 brand Netgear WNDR3400v1 Broadcom Broadcom Broadcom Netgear WNDR3400v2 Broadcom Broadcom Broadcom Netgear WNDR3400v3 Broadcom Broadcom Broadcom

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.

For a list of all currently documented Netgear device with specifications, see Netgear.

• 300 Mbps - 2SS 5GHz 802.11n (40MHz chan.),

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = AN600 class

Overview

• Simultaneous Dual-Band, 10/100 Mbps Ethernet (FE)

The default SSIDs for the device are assumed to be NETGEAR and NETGEAR-5G.

OEM: Foxconn / Hon Hai / Ambit U12H155T00

Links of Interest

The device is in the DD-WRT Supported Device table, and has its own wiki.

• On the DD-WRT forums (test build on pg7)
• WNDR3400 WiFi 5GHz LED doesn't flash with activity
• Netgear WNDR3300v2 and WNDR3400
• GURU's Netgear WNDR3400 update
• Netgear WNDR3400 support

Flashing

Flashing DD-WRT

On the DDWRT Wiki
Support started version: Supported 17567
Current supported version: ?

Source

Step 1: Backup your current router configuration

1. Login to your router… probably at http://192.168.1.1
2. Find the maintenance group in the left menu and click on ‘Backup Settings‘
3. Click the button labeled ‘Back Up’ You’ll be prompted to download a file, save it and stick it on your desktop or someplace safe in case you need it later.

Step 2: Download factory firmware (just in case!!)

As a precaution, I chose to download the factory firmware ahead of time so I could have it on hand if this entire process fails and I need to revert everything.

• Download: Recovery Instructions from Netgear
• Download: WNDR3400v1 Firmware

Note: These recovery instructions have not been tested by me, use at your own risk.

Step 3: Download the DD-WRT firmware

Downloading via the normal DD-WRT process didn’t work out because it stated the router wasn’t compatible and therefore wouldn’t provide a link.

There is now a WNDR3400 chk file included in the official SVN stream, you can browse the 12/08/2011 release files here.

• Download: dd-wrt.v24-17990_NEWD-2_K2.6_mini-WNDR3400.chk

Step 4: Flash DD-WRT on to the router

Before flashing the firmware on your router, it’s highly highly suggested to do a 30-30-30 reset. You can find instructions for this here: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486

Quoting from the “peacock” thread in the DD-WRT forums:

“Failing to do a hard reset and failing to wait after flashing are the two most common NOOB errors that lead them to a world of unnecessary dd-wrt pain! This is not a minor optional step. The firmware writes information to the Nvram. This step clears that information. If you don’t clear it properly, parts of the old information be present with the new firmware, which can make it not operate properly. Don’t cut corners. Doing it before you upgrade can be very important; a hard reset is not just for after upgrades.”

After performing the 30-30-30 reset, log back in to the router and flash it via the web gui.

1. Do NOT use a wireless connection to upload firmware. Use a wired (LAN) connection.
2. Login to your router… probably at http://192.168.1.1
3. Find the maintenance group in the left menu and click on “Router Upgrade”
4. Click the browse button and find dd-wrt.v24-17990_NEWD-2_K2.6_mini-WNDR3400.chk

1. Click the “Upload” button and wait for the process to complete.
2. After the process is done and the router reboots, you can connect to http://192.168.1.1 and should see DD-WRT loaded successfully.
3. Perform another 30-30-30 reset.
4. After the reset procedue is done, login to the router and set a username & password.

Step 5: Upgrade to latest version of DD-WRT:

Now we have DD-WRT running on our WNDR3400v1, we can upgrade to the latest release using the normal flash method via the web gui.

With the latest release, I attmpted to load the “mega” file and it was a success…

• Download: dd-wrt.v24-17990_NEWD-2_K2.6_mega-nv64k.bin

The upgrade process is pretty simple at this point. Some suggest doing a hard reset before and after upgrading. Since I just did a hard reset after installing DD-WRT, it’s not really needed again unless you make some configuration changes before you upgrade.

1. Do a 30-30-30 reset if you need to.
2. Do NOT use a wireless connection to upload firmware. Use a wired (LAN) connection.
3. Login to your router… probably at http://192.168.1.1
4. Click on the Administration tab and then click on Firmware Upgrade:

1. Choose the option to Reset to Defaults after flashing.
2. Click browse and find dd-wrt.v24-17990_NEWD-2_K2.6_mega-nv64k.bin
3. Click the “Upgrade” button at the bottom of the page and wait….
   • The router will take a few minutes to upload the file and flash the firmware. During this time, the power light will flash.
   • A new page will open confirming that the upload was successful.
   • It’s advised to wait at least 5 minutes before clicking continue.
4. Do a 30-30-30 reset.
5. After the reset procedue is done, login to the router and set a username & password.

You should now see something like the screen below that shows the 17990 firmware loaded on your WNDR3400v1:

I’ve been running this on my router for a couple of days and all the features I need are active and working. Your mileage may vary….

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki
OpenWrt Target: bcm47xx
OpenWrt Subtarget: mips74k
OpenWrt Package architecture: mipsel_74kc
Support started version: 14.07
Current supported version: 23.05.5

• WIP

• So far tests indicate no WebUI, No Wireless, it has telnet access.

Currently, there is a development version of OpenWRT for this router located

at: /trunk/brcm47xx/openwrt-wndr3400_v1-squashfs.chk

Also, this is not beginner firmware. If you've never dealt with a console, avoid!

To flash:

1. Do a 30/30/30 reset.
2. With the stock firmware, flash that build.
3. Do a 30/30/30 reset again.

By default, OpenWRT does not include a web interface and as such,

must be installed using opkg or must be compiled with it included.

Telnet is available. Once the password is changed, telnet becomes

unavailable and ssh becomes available.

Support for this model is still in development so not everything works.

The build linked above is using kernel version 3.6 as of this writing.

I've been told that 3.8 works much better for it. Unconfirmed however.

Wireless is disabled by default. To enable, type in the console:

uci set wireless.@wifi-device[0].disabled=0

Flashing Tomato

• Netgear WNDR3400 v1 - (beta) Tomato support

• Beta
• Note: Intial flash must be done from the OEM firmware.

If your running dd-wrt, revert to the OEM firmware first.

1. restore default settings
2. flash using tomato image via GUI
3. after flash leave router for 5–7 minutes until ping 192.168.1.1 will return
4. log into Tomato and first of all erase nvram!!
5. after erase 2nd radio will disapear. Dont panic :) Just make reboot one more time
6. log into tomato and Have fun

TomatoUSB Support Details:

- both radios works

- usb works

- power led and usb led works correct

- wps and reset buttons works

- VLANs are not supported yet

- wireless leds may not work correct

- upgrade router via GUI will brick router!!

Image: tomato-Netgear-3400v1-K26USB-1.28.RT-101.chk

Upgrading

Updating DD-WRT

If dd-wrt is already on the router follow these instructions. If stock firmware is on the router follow the flashing instructions.

1. Check for recommended builds here first.
2. Set your computer to a static IP of 192.168.1.7. (or to whatever subnet the router is on) Disable all firewalls and security. Disable wireless on your computer and only have the router connected to the flashing computer by the ethernet cable between the two.
3. Hard reset or 30/30/30 (If the router supports it, if not, reset to defults in the GUI) prior to flashing. Wait. Check for password page on re-login and change password.
4. Flash firmware. You can use the webgui except if you have a belkin router. (For belkin use tftp.exe to flash)
5. Wait...at least three minutes. Lights should return to normal. See important2, below. Failing to wait is how most people brick their routers.
6. Do a power cycle of the router. (Unplug the cord, count to 30 and plug it back in.)
7. Wait for the lights to return to normal usually about 2 minutes.
8. Hard reset or 30/30/30 again (If the router supports it, if not, reset to defults in the GUI). Wait. Check for the password page and re-login to change the password. Then you can reconfigure your settings manually.
9. Once configured set your computer back to autoIP and autoDNS.
   

Important1: This Hard reset or 30/30/30 works fine for Asus router, but you do have to power cycle after the reset.

Important2: After you flash the firmware, and before you do the hard reset, the router will be building some nvram settings. YOU MUST WAIT FOR THIS TO FINISH PRIOR TO DOING ANYTHING WITH THE ROUTER INCLUDING A HARD RESET. Usually, you can tell when this process is completed by the WAN light coming on, but it does take several minutes. Go have a beer. There are starting to be more and more people who BRICK their routers by not waiting until the nvram is rebuilt, PRIOR to doing a hard reset. YOU NEED TO WAIT!

Reverting

Reverting to OEM Firmware from TomatoUSB

1. flash ofw image via GUI
2. after flash router wuill brick and power led will blink green light
3. flash ofw image one more time using tftp client
4. after flash make 30-30-30 reset

Original image: WNDR3400-V1.0.0.50_20.0.59-OFW.chk

Reverting to OEM Firmware from DD-WRT

Per Eko

There is simple way to flash original firmware.

-with router running dd-wrt, telnet in, do "mtd erase linux", wait until finished (2-3 min), then type "reboot"

-now router waits for new firmware - tftp the original .chk file (with your PC set to static IP 192.168.1.10 etc)

-when tftp transfer finishes, wait 3-4 min...

JTAG-Serial Info

JTAG

JTAG Pinouts

J14 - DO NOT HOOK UPTO J10

 nTRST  1o o2  GND
   TDI  3o o4  GND
   TDO  5o o6  GND
   TMS  7o o8  GND
   TCK  9o o10 GND
 nSRST 11o o12 N/C

Using Universal JTAG Adapter

  white  1o o2  black
    red  3o o4  GND
   blue  5o o6  GND
  green  7o o8  GND
 yellow  9o o10 GND
 orange 11o o12 N/C

Serial

Serial Pinouts

JP1 = 3.3v TTL Serial, 115200/8/N , 1 row of six pins

 GND 6 o
 RX  5 o
 N/C 4 o
 N/C 3 o
 TX  2 o
 VCC 1 o

this setup was tested on the 3/20/2013, some other websites are showing the RX and TX opposite and this why does not work for this type of router

Serial Recovery

As of March 2013

1. After Setting up the Putty session, power up your router with the USB serial TTL cable you should see some info scrolling on the screen, press control-c rapidly and it will come with a promt CFE>
2. type on this prompt tftpd to start the tftpd server, you should see the message saying the command START TFTP SERVER and the message READING::: ts ready to send the new firmware.
3. assuming you have download the latest Firmware from Netgear do the following, open a cmd terminal and go to the folder you have save the firmware, type the following : tftp -i 192.168.1.1 put FIRMWARE_FILE.chk, you should see some comments about this on the putty session like reading processing and programing.
4. the router will start itself give it some time until finish

it took me a while to sort out this router but i finally did it doing it this way.

Boot Log

Boot log • >>

Decompressing..........done CFE for WNDR3400 version: v1.0.8 Build Date: Thu Apr 22 16:51:23 CST 2010 Init Arena Init Devs. Boot partition size = 262144 (0x40000) Found a 8MB ST compatible serial flash et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.28 CPU type 0x19740: 453MHz Tot mem: 65536 KBytes Device eth0: hwaddr E0-46-9A-7F-85-D7, ipaddr 192.168.1.1, mask 255.255.255.0 gateway not set, nameserver not set Loader:raw Filesys:tftp Dev:eth0 File:192.168.1.2:vmlinuz Options: (null) Loading: Failed. Could not load 192.168.1.2:vmlinuz: Timeout occured Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #7 Thu Sep 13 18:53:59 CEST 2012 CPU revision is: 00019740 Found a 8MB ST compatible serial flash Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Built 1 zonelists. Total pages: 16256 Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200 Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 256 (order: 8, 1024 bytes) CPU: BCM4716 rev 1 pkg 10 at 453 {{abbr|MHz|megahertz}} Using 226.500 {{abbr|MHz|megahertz}} high precision timer. console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 61828k/65536k available (33k kernel code, 3644k reserved, 2726k data, 116k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 PCI: Using membase 8000000 PCI: Initializing host PCI: Reset RC PCI: Fixing up bus 0 PCI: Fixing up bridge PCI: Fixing up bridge PCI: Enabling device 0000:01:00.1 (0004 -> 0006) PCI: Fixing up bus 1 NET: Registered protocol family 2 Time: MIPS clocksource has been installed. IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered squashfs: version 3.0 (2006/03/15) Phillip Lougher io scheduler noop registered (default) HDLC line discipline: version $Revision: 4.8 $, maxframe=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A PPP generic driver version 2.4.2 MPPE/MPPC encryption/compression module registered NET: Registered protocol family 24 PPPoL2TP kernel driver, V0.18.3 PPTP driver version 0.8.5 pflash: found no supported devices Creating 6 MTD partitions on "sflash": 0x00000000-0x00040000 : "pmon" 0x00040000-0x00790000 : "linux" 0x00151238-0x00640000 : "rootfs" 0x00640000-0x00780000 : "jffs2" 0x007f0000-0x00800000 : "nvram" 0x007e0000-0x007f0000 : "board_data" u32 classifier OLD policer on Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (512 buckets, 4096 max) ip_tables: (C) 2000-2006 Netfilter Core Team ipt_account 0.1.21 : Piotr Gasidlo <quaker@barbara.eu.org>, http://www.barbara.eu.org/~quaker/ipt_account/ net/ipv4/netfilter/tomato_ct.c [Sep 13 2012 16:17:11] NET: Registered protocol family 1 NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 116k freed Warning: unable to open an initial console. emf: module license 'Proprietary' taints kernel. eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.147.0 eth1: Broadcom BCM4329 802.11 Wireless Controller 5.10.147.0 PCI: Enabling device 0000:01:01.0 (0000 -> 0002) Netgear WNDR3400 eth2: Broadcom BCMa8d8 802.11 Wireless Controller 5.10.147.0 / # lo: File exists

USB Info

DD-WRT USB

• The USB port is where you can connect an external USB hard drive or flash drive. Which can do a multitude of things. You can use in as a NAS, storage for a FTP server, use Optware to run external programs like torrent software, samba for sharing files to network, share a USB printer with network... The list of possibilities is long, it just takes a little research.

• ProFTPd, samba, dlna, raid support is included in most the newer builds of dd-wrt. Check the features chart to be sure.

Tomato USB

Most newer Tomato forks comes with file sharing, ftp server and media server built in.

Tutorial: How to set up NAS and Optware on Tomato FOR TOTAL NOOBS

Vlan Info

DD-WRT Vlan Info

• TechInfoDepot:DD-WRT/VLAN Support Testing Needed

Pictures

Netgear Images

• 

  Angle Stand

• 

  Angle Flat

• 

  Front

DarkShadow's Unit

• 

  Board Top

• 

  Board Top2

• 

  Antenna mod

Joe714na's Unit

• 

  Top of the PCB

• 

  Bottom of the PCB

• 

  Controller

• 

  GPIO Cable

• 

  RAM

• 

  Flash+unknown IC

FCCID PY309300116

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 

Notes

Known GPIO pin support:

gpio enable 0 - Turns on 5 GHz blue

gpio disable 0 - Turns off 5 GHz blue

gpio enable 2 - Turns off USB

gpio disable 2 - Turns on USB

gpio enable 3 - Turns power light to green

gpio disable 3 - Turns power light off

gpio enable 7 - Turns power light to orange

gpio enable 7 - Turns power light from orange off

DD-WRT Notes

The WNDR3400 CVNA (Cablevision edition) default username and password is admin/optimum

Hardware Modification

WNDR3400v2 model will feature the BCM5358 chipset.

Antenna Mod

• Antenna MOD Images
• 
• 
• 
• 
• 
• 
• 

See also

• Netgear WNDR3400v1
• Netgear WNDR3400v2 (Netgear WNDR3400v2/nvram)
• Netgear WNDR3400v3 (Netgear WNDR3400v3/nvram)