Linksys WRT54G v6.0

From TechInfoDepot
(Redirected from Linksys WRT54G v6)
Jump to navigationJump to search
multiple revisions of this device, use caution
bg (G54)
Wireless-G Broadband Router
Linksys WRT54G-02.jpg
Support
Wikipedia
InfoDepot Wiki
WikiDevi.wi-cat.ru
3rd Party Firmware
dd-wrt
OpenWrt
Not for 2MB Devices
Tomato any flavor
Not for 2MB Devices
Gargoyle
Incompatible
Platform
BrandModelRev
Linksys WRT54G v6.0
Serial number prefix
CDFD
FCC ID
IC ID
Type
wireless router
Series
WRT54G
CPU1
Broadcom BCM5352E
CPU1 Type
MIPS BMIPS3300 (R1)
CPU1 Speed
200 MHz
Flash1 Chip
Spansion S29AL016D90TFI01
Flash1 Size
2 MiB2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br /> (Parallel)
RAM1 Size
8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br />
RAM1 Chip
SK hynix HY57V641620ETP-H
nvram Size
32K
ETH chip1
Broadcom BCM5352E
Switch
Broadcom BCM5352E
Ethernet Port Count
1-100MbE-WAN
4-100MbE-LAN
Wired Standard
IEEE 802.3/3u

802dot11 OUI: 00:18:39 (8 E, 17 W), 00:18:F8 (10 E, 14 W)
Ethernet OUI: 00:18:39 (8 E, 17 W), 00:18:F8 (10 E, 14 W)

Stock bootloader
BSP
Stock FW OS
VxWorks
Expansion IF types
none specified
Power
12 VDC, 0.5 A
Connector type
barrel
Serial Port (UART)
yes, 10-pin header, unpopulated, (115200 8N1)
JTAG Port
yes, 12-pin header, unpopulated

Additional chips
2.4GHz Power Amplifier IC;Skyworks;SE2528L;SiGe, 2528L, 617CL;1;

Other

Default SSID: linksys (53 addl. devices)
Default IP address: 192.168.1.1
the IP 192.168.1.1 is used by 1304 additional devices
of which 153 are Linksys devices
Default login user: blank
Default login password: admin
blank:admin credentials used by 267 additional devices
of which 134 are Linksys devices

Manuf/OEM/ODM
3rd Party Firmware Support
DD-WRT • (List)
Retail
Country of manuf China
Physical
Dimensions
7.32" x 1.89" x 6.06"
Radio 1
Chip1
Broadcom BCM5352E
Chip2
Broadcom BCM2050
Wireless interface OUI
00:18:39, 00:18:F8
Antenna Connector Type
RP-TNC
Wireless Standard
IEEE 802.11b/g
802.11g
up to 54 Mbps
802.11b
up to 11 Mbps
WiFi Operating Frequency
2.4 GHz
Radio cor_rev
9
 FCC ID
Linksys WRT54GS v6.0Q87-WT54GV60
 CPU1 brandRadio1 chip1 brandRadio1 chip2 brand
Linksys WRT54G v1.0BroadcomBroadcomBroadcom
Linksys WRT54G v1.1BroadcomBroadcomBroadcom
Linksys WRT54G v2.0BroadcomBroadcomBroadcom
Linksys WRT54G v2.2BroadcomBroadcomBroadcom
Linksys WRT54G v3.0BroadcomBroadcomBroadcom
Linksys WRT54G v3.1BroadcomBroadcomBroadcom
Linksys WRT54G v4BroadcomBroadcomBroadcom
Linksys WRT54G v5.0BroadcomBroadcomBroadcom
Linksys WRT54G v5.1BroadcomBroadcomBroadcom
Linksys WRT54G v5.2BroadcomBroadcomBroadcom
Linksys WRT54G v6.0BroadcomBroadcomBroadcom
Linksys WRT54G v7.0AtherosAtheros
Linksys WRT54G v7.2BroadcomBroadcom
Linksys WRT54G v8.0BroadcomBroadcom
Linksys WRT54G v8.1BroadcomBroadcom
Linksys WRT54G v8.2BroadcomBroadcom
Linksys WRT54G-TMBroadcomBroadcomBroadcom
Linksys WRT54GHRalinkRalink
Linksys WRT54GP2MarvellMarvellMarvell
Linksys WRT54GP2A-ATIntel XScaleInprocommRFMD

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.

For a list of all currently documented Linksys device with specifications, see Linksys.

54 Mbps - 2.4GHz 802.11g = G54 class


Overview

The stock firmware on these devices contains VxWorks, not Linux. See the Linksys v5.0, v5.1, and v6.0 bellow for instructions on flashing the units with DD-WRT.

"3763-14140704R" is silkscreened on the board.

The devices can be configured with SecureEasySetup. Being configured this way, the devices will assume SSIDs of linksys_SES_XXXXX where XXXXX appears to be a random number. Before being configured, but after the SES button is pressed, the device assumes an SSID of linksys_OW_XXXXX where XXXXX is a random number.

Links of Interest

Flashing

Supported by dd-wrt as of = ?

Flashing DD-WRT

On the DD-WRT Wiki

 

IN SPITE OF SOME OTHER INSTRUCTIONS ELSEWHERE, YOU REALLY NEED TO CREATE A CUSTOM VX Image for your router. If you don’t you will get a generic MAC address on your router and a generic MAC address will mean most ISP won’t let you connect to the Internet. Here is how to do it properly:

Download the zipped files in GV5Flash.zip

Or you can download the same file from me here: Gv5Flash.zip

  1. Read the peacock announcement found here: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
  2. Do a Hard reset or 30/30/30 on the router according to note 1 of the peacock announcement (30/30/30)
  3. Set a static IP on your computer to 192.168.1.7. Subnet mask should be 255.255.255.0.
  4. Connect the LAN cable from your computer to a LAN port of your router. Make sure your router is plugged in. Nothing should be connected to your computer or the router except the LAN cable between them. Turn your firewall and any wireless computer connections OFF.
  5. Unzip the file you downloaded and place it in a location you can easily find on your computer.
  6. Unzip the VXImgToolGui.zip file to the same folder as where you placed the other files you downloaded.
  7. Start VXImgToolGui.exe.
    1. Make sure the top button is on the left for WRT54G, not the right for WRT54GS.
    2. Put the MAC address from the bottom of your router in the box that says "Desired MAC".
    3. Click on the three dots next to "output image" and save the file as My54gImage.bin in the same folder as everything else is located.
  8. Power cycle the router (unplug the power from the router for 30 seconds and then plug it back in).
  9. Open your browser to 192.168.1.1 by putting that in the browser address window of your browser. You should open the linksys webgui and NOT a page that says Management Mode. If you see management mode, power cycle the router again.
  10. Enter "root" as the username and "admin" as the password.
  11. Go to Administration and Firmware Upgrade.
  12. Navigate to the folder that you are using, and select vxworks_prep_03.bin.
  13. Hit upgrade.
  14. Wait for FIVE FULL MINUTES. Go for a walk. Don't you TOUCH that router for FIVE MINUTES.
  15. When five full Earth minutes have passed, power cycle the router.
  16. Refresh your browser window. If you get a blank window, clear your browser cache. NOW you should be in the MANAGEMENT MODE window.
  17. Select the My54gImage.bin file that you created. Hit Apply.
  18. Wait for the "Upgrade Success" message, and then WAIT FIVE FULL MINUTES again. Don't TOUCH your router.
  19. Start tftp.exe.
    1. Enter 192.168.1.1 as the address in the top box of tftp.exe.
    2. Leave the password blank.
    3. Select the 12548 Newd_Micro.bin firmware.
    4. Set retries to 99.
    5. Power cycle the router.
    6. Count to 2.
    7. Hit upgrade.
  20. When you get a success, wait FIVE FULL minutes.
  21. If you don't get success, repeat from steps 19(4) up to this one. If you still don't get success, clear your browser cache. Try using a different browser as well, to navigate to 192.168.1.1.
  22. When you can access the dd-wrt webgui using a browser at 192.168.1.1, power cycle the router.
  23. When you can again access the dd-wrt webgui using a browser at 192.168.1.1, do another Hard reset or 30/30/30 on the router.
  24. Reset your computer Ethernet connection to auto IP and auto DNS.
  25. Check for recommended builds here.

Upgrading

Updating DD-WRT

If dd-wrt is already on the router follow these instructions. If stock firmware is on the router follow the flashing instructions.

  1. Check for recommended builds here first.
  2. Set your computer to a static IP of 192.168.1.7. (or to whatever subnet the router is on) Disable all firewalls and security. Disable wireless on your computer and only have the router connected to the flashing computer by the ethernet cable between the two.
  3. Hard reset or 30/30/30 (If the router supports it, if not, reset to defults in the GUI) prior to flashing. Wait. Check for password page on re-login and change password.
  4. Flash firmware. You can use the webgui except if you have a belkin router. (For belkin use tftp.exe to flash)
  5. Wait...at least three minutes. Lights should return to normal. See important2, below. Failing to wait is how most people brick their routers.
  6. Do a power cycle of the router. (Unplug the cord, count to 30 and plug it back in.)
  7. Wait for the lights to return to normal usually about 2 minutes.
  8. Hard reset or 30/30/30 again (If the router supports it, if not, reset to defults in the GUI). Wait. Check for the password page and re-login to change the password. Then you can reconfigure your settings manually.
  9. Once configured set your computer back to autoIP and autoDNS.

Important1: This Hard reset or 30/30/30 works fine for Asus router, but you do have to power cycle after the reset.

Important2: After you flash the firmware, and before you do the hard reset, the router will be building some nvram settings. YOU MUST WAIT FOR THIS TO FINISH PRIOR TO DOING ANYTHING WITH THE ROUTER INCLUDING A HARD RESET. Usually, you can tell when this process is completed by the WAN light coming on, but it does take several minutes. Go have a beer. There are starting to be more and more people who BRICK their routers by not waiting until the nvram is rebuilt, PRIOR to doing a hard reset. YOU NEED TO WAIT!

Reverting

Reverting to OEM Firmware from DD-WRT

To get back to VxWorks (default firmware) you need special instructions.

http://www.bitsum.com/openwiking/owbase/ow.asp?WRT54G5%5FCFE#h13
http://www.scorpiontek.org/portal/content/view/31/36/

JTAG-Serial Info

JTAG

JTAG Pinouts

 nTRST   1o o2	GND
   TDI   3o o4	GND
   TDO   5o o6	GND
   TMS   7o o8	GND
   TCK   9o o10	GND
 nSRST  11o o12  N/C

Using Universal JTAG Adapter

 white    1o o2	 black
   red    3o o4	 GND
  blue    5o o6	 GND
 green    7o o8	 GND
 yelow    9o o10  GND
 orange  11o o12  N/C

DD-WRT JTAG Recovery

  • /noemw /nocwd switches required
  1. Backup CFE x2 (Compare the files, they must match exactly or there is something wrong with your JTAG setup)
  2. Erase Wholeflash x2
  3. Flash CFE
  4. Unplug Power
  5. Unplug JTAG Cable

TFTP:

  1. Set Rig ip static 192.168.1.10
  2. Plug network cable from rig to port 1
  3. Get TFTP ready, server ip - 192.168.1.1, Password - blank, file - dd-wrt.v24_micro_generic.bin
  4. Plug in power
  5. As soon as windows says "connected" hit upgrade. May have to use a network hub to make sure windows is always connected.
  6. Hard Reset 30\30\30

Serial

Serial Pinouts

 VCC  1 o o 2  VCC
 TX1  3 o o 4  TX0
 RX1  5 o o 6  RX0
 N/C  7 o o 8  N/C
 GND  9 o o 10 GND

DD-WRT Serial Recovery

Modified Redhawk0 instructions

  1. Print out these instructions for Off-Line use
  2. Connect PC to router with a network cable
  3. Configure PC with a static IP of 192.168.1.10
  4. Connect Serial cable
  5. Start one of the programs from above
  6. Get TFTP ready with file selected
  7. Use dd-wrt.v24_micro_generic.bin
  8. Connect power to the router
  9. start a rapid fire Cntl-C as you plug the router to power
  10. type "nvram erase" w/o quotes, hit enter
  11. type "flash -noheader : flash1.trx" w/o quotes, this starts the tftp daemon, hit enter
  12. but have TFTP ready
  13. Click go or start on TFTP
  14. give it 5 minutes after it finishes
  15. then power cycle....Hard reset or 30/30/30...then config
  16. when it stops spitting out txt....hit the enter key...you should get a login prompt...at that point, power cycle it, hard reset...then config
  17. you'll see it boot up


vlan Info

DD-WRT vlan Info

Confirmed the WRT54G v6.0 supports port-based vlans via the GUI.

Confirmed the WRT54G v6.0 supports port-based vlans via nvram with micro-plus-SSH.

WRT54G v6.0's ports are mapped like this:

1 2 3 4 | case labels
3 2 1 0 | nvram port numbers

Defaults

root@DD-WRT:~# nvram show | grep vlan.ports
vlan1ports=4 5
vlan0ports=3 2 1 0 5*
size: 19179 bytes (13589 left)
root@DD-WRT:~# nvram show | grep port.vlans
port5vlans=0 1 16
port4vlans=0
port3vlans=0
port2vlans=0
port1vlans=0
port0vlans=1
size: 19179 bytes (13589 left)
root@DD-WRT:~# nvram show | grep vlan.hwname
vlan1hwname=et0
vlan0hwname=et0
size: 19179 bytes (13589 left)
root@DD-WRT:~# lsmod
Module                  Size  Used by
ip_nat_pptp             2192   0 (unused)
ip_conntrack_pptp       2524   1
ip_nat_proto_gre        1552   0 (unused)
ip_conntrack_proto_gre    2312   0 [ip_nat_pptp ip_conntrack_pptp]
switch-robo             5036   0 (unused)
switch-core             5984   0 [switch-robo]
root@DD-WRT:~# ls /proc/switch
eth0
root@DD-WRT:~# cat /proc/switch/eth0/vlan/0/ports
0       1       2       3       5t*
root@DD-WRT:~# cat /proc/switch/eth0/vlan/1/ports
4       5t
root@DD-WRT:~# cat /proc/switch/eth0/vlan/2/ports
4
root@DD-WRT:~#

Commands

root@DD-WRT:~# nvram set vlan1ports="3 4 5"
root@DD-WRT:~# nvram set vlan0ports="2 1 0 5*"
root@DD-WRT:~# nvram commit
root@DD-WRT:~# reboot

nvram

root@DD-WRT:~# nvram show | grep vlan.ports
vlan1ports=3 4 5
vlan0ports=2 1 0 5*
size: 19303 bytes (13465 left)
root@DD-WRT:~# nvram show | grep port.vlans
port5vlans=0 1 16
port4vlans=0
port3vlans=0
port2vlans=0
port1vlans=0
port0vlans=1
size: 19303 bytes (13465 left)
root@DD-WRT:~# nvram show | grep vlan.hwname
vlan1hwname=et0
vlan0hwname=et0
size: 19303 bytes (13465 left)
root@DD-WRT:~#

GUI

root@DD-WRT:~# nvram show | grep vlan.ports
vlan0ports=3 2 1 0 5*
vlan1ports=4 5
size: 17470 bytes (15298 left)
root@DD-WRT:~# nvram show | grep port.vlans
port5vlans=0 1 16
port3vlans=0 18 19
port1vlans=0 18 19
port4vlans=1 18 19
size: 17470 bytes (15298 left)
port2vlans=0 18 19
port0vlans=1 18 19
root@DD-WRT:~# nvram show | grep vlan.hwname
vlan1hwname=et0
size: 17470 bytes (15298 left)
vlan0hwname=et0
root@DD-WRT:~#

Pictures

DarkShadow's Unit
WikiDevi Images
FCCID Q87-WT54GV60

Notes

DD-WRT Notes

Also see this page: Version 5 And 6 Router Information

There is good information at the scorpiontek site: http://www.scorpiontek.org/portal/content/view/27/36

A CFE compressor is available for the Gv5.0,5.1, and 6.0. It enables micro_plus to be put on the router. Click here.