Belkin F7D8302

Default SSID: Belkin.XXXX (6 addl. devices)
, Belkin.XXXX_5GHz (2 addl. devices)
Default IP address: 192.168.2.1
the IP 192.168.2.1 is used by 297 additional devices
of which 99 are Belkin devices

Manuf/OEM/ODM

Arcadyan WG8017 F22 1-LF-AK

3rd Party Firmware Support

DD-WRT • (List)
, Tomato (Toastman) • (List | DLs)
, FreshTomato • (List | DLs)

Retail

FCC approval date

23 February 2010

(Est.) release date

24 March 2010

UPC

879562039533
(UPC DB, On eBay)

ASIN

B0045HJME4

Country of manuf

China

Radio 1

Chip1

Broadcom BCM4718A1

Wireless interface OUI

94:44:52

Antenna Connector Type

none specified

MIMO status

2x2:2

Wireless Standard

IEEE 802.11b/g/n

802.11n

up to 300 Mbps

802.11g

up to 54 Mbps

802.11b

up to 11 Mbps

WiFi Operating Frequency

2.4 GHz

Radio cor_rev

Radio 2

Chip1

Broadcom BCM43224

Wireless interface OUI

94:44:52

Antenna Connector Type

U.FL

MIMO status

2x2:2

Wireless Standard

IEEE 802.11a/n

802.11n

up to 300 Mbps

802.11a

up to 54 Mbps

WiFi Operating Frequency

5 GHz

	FCC ID
Belkin F7D4302	K7SF7D4302V1

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.

For a list of all currently documented Belkin device with specifications, see Belkin.

• 300 Mbps - 2SS 5GHz 802.11n (40MHz chan.),

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = AN600 class

Overview

"P/N: 141701620001J REV: 01" is silkscreened on the board in the FCC photos.

Links of Interest

Flashing

NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power.

Flashing dd-wrt

Please insert instructions here

Flashing Tomato

Please insert instructions here

JTAG-Serial Info

Serial

Serial Pinouts

J3 |> [+ TX RX -]

1. 3.3
2. TX
3. RX
4. GND

Hyper terminal Setup in Windows XP • >>
In Windows XP, Click Start Button - All Programs - Accessories - Communication - HyperTerminal Enter a name for the connection, Click ok Choose com port you adapter is plugged into, Click ok Set: Bits per second = 115200 Data Bits = 8 Parity = none Stop bits = 1 Flow control = none Click ok Click File - Save As, and select a place to save it to so you don't have to enter the settings again.

Hyper terminal Setup in Windows XP • >>

 In Windows XP, Click Start Button - All Programs - Accessories - 
    Communication - HyperTerminal
 Enter a name for the connection, Click ok
 Choose com port you adapter is plugged into, Click ok
 Set:
  Bits per second = 115200
  Data Bits = 8
  Parity = none
  Stop bits = 1
  Flow control = none
 Click ok
 Click File - Save As, and select a place to save it to so you 
              don't have to enter the settings again.

Putty Setup in Windows XP • >>
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open

Putty Setup in Windows XP • >>

 After installing putty, run it
  Serial line = The COM port your using for serial (ie. COM3)
  Speed = 115200
 Click on Serial under Connection
  Serial line to connect to = same as above (Serial line)
  Speed (baud) = 115200
  Data bits = 8
  Stop bits = 1
  Parity = None
  Flow control = None
 Click Session
  Enter a name for your connection under saved sessions
 Click Save
 Click Open

Mincom setup in Linux

After installing minicom, run it with -s flag for setup (sudo minicom -s)
  Under "Serial Port Setup":
  Use 'A' to set the serial device (ie. /dev/ttyUSB0)
  Use 'E' to set the Bps/Par/Bits
    Speed (baud) = 115200
    Data bits = 8
    Stop bits = 1
    Parity = None
    Flow control = None
 Save as dfl