Tenda W300A/Serial info

From TechInfoDepot
Jump to navigationJump to search

boot log

boot log
 U-Boot 1.1.3 (Feb 22 2008 - 16:48:17)
 
 Board: RT2880 DRAM:  16 MB
 
  twe0 set to <NULL>
 
  toe0 set to <NULL>
 flash_protect ON: from 0xBF000000 to 0xBF02479B
 protect on 0
 protect on 1
 protect on 2
 flash_protect ON: from 0xBF030000 to 0xBF03FFFF
 protect on 3
 ============================================ 
 ASIC -VerB/C (MAC to 100PHY Mode)
 DRAM COMPONENT=64Mbits 
 DRAM BUS=32BIT 
 Total memory = 16Mbytes
 Date:Feb 22 2008  Time:16:48:17
 ============================================ 
 
  D-CACHE set to 4 way 
  I-CACHE set to 4 way 
 
  ##### The CPU freq = 266 MHZ #### 
 
  SDRAM bus set to 32 bit 
  SDRAM size =16 Mbytes
 
 Please choose the operation: 
    1: Load system code to SDRAM via TFTP. 
    2: Load system code then write to Flash via TFTP. 
    3: Boot system code via Flash (default).
    4: Entr boot command line interface.
    5: Load ucos code to SDRAM via TFTP. 
 
 
 3: System Boot system code via Flash.
 ## Booting image at bf050000 ...
    Image Name:   Linux Kernel Image
    Created:      2008-10-29  18:46:32 UTC
 System Control Status = 0x02910084 
    Image Type:   MIPS Linux Kernel Image (lzma compressed)
    Data Size:    2447621 Bytes =  2.3 MB
    Load Address: 88000000
    Entry Point:  88190040
    Verifying Checksum ... OK
    Uncompressing Kernel Image ... OK
 No initrd
 ## Transferring control to Linux (at address 88190040) ...
 ## Giving linux memsize in MB, 16
 
 
 Starting kernel ...
 
 
 
 THIS IS ASIC
 ramsize = 16 MBytes
 rambase not set, set to default (0x08000000)
 MEMORY DESCRIPTOR dump:
 [0,883d0b80]: base<08000000> size<01000000> type<Free RAM memory>
 
  The CPU feqenuce set to 266 MHz
 CPU revision is: 0001906c
 icache: sets:256, ways:4, linesz:16 ,total:16384, waybit:12, flags:0x0
 dcache: sets:256, ways:4, linesz:16 ,total:16384, waybit:12, flags:0x0
 i waysize = 4096, d waysize = 4096, i sets= 256, d sets=256
 Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
 Primary data cache 16kB, 4-way, linesize 16 bytes.
 [setup_scache]:1032
 Linux version 2.4.30 (root@linux-r3ht) (gcc version 3.3.6) #1 Thu Oct 30 02:42:35 CST 2008
 Determined physical RAM map:
  memory: 01000000 @ 08000000 (usable)
 Initial ramdisk at: 0x881c2000 (1855488 bytes)
 On node 0 totalpages: 36864
 zone(0): 36864 pages.
 zone(1): 0 pages.
 zone(2): 0 pages.
 Kernel command line: console=ttyS1,57600n8 root=/dev/ram0
 cause = e080804c, status = 1000ff00
 calculating r4koff... 0028b0aa(2666666)
 CPU frequency 266.67 MHz
 Using 133.333 MHz high precision timer.
 Calibrating delay loop... 266.24 BogoMIPS
 Memory: 10872k/16384k available (1585k kernel code, 5512k reserved, 1912k data, 92k init, 0k highmem)
 Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
 Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
 Mount cache hash table entries: 512 (order: 0, 4096 bytes)
 Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
 Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
 Checking for 'wait' instruction...  unavailable.
 POSIX conformance testing by UNIFIX
 pci.c pcibios_init():840
 BAR0 at slot 0 = 8
 pci.c pcibios_fixup_resources():640
 bus = 0, dev = 0, fun = 0
 dev= 0x88564c00
 Linux NET4.0 for Linux 2.4
 Based upon Swansea University Computer Society NET3.039
 Initializing RT netlink socket
 Starting kswapd
 devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
 devfs: boot_options: 0x1
 squashfs: version 3.1 (2006/08/19) Phillip Lougher
 pty: 256 Unix98 ptys configured
 Ralink RT2880 gpio driver start init
 SetGPIOType: id [12] type[0]
 SetGPIOType: id [11] type[0]
 SetGPIOType: id [13] type[1]
 SetGPIOType: id [0] type[1]
 Ralink RT2880 gpio driver initialized
 spidrv_major = 217
 Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
 ttyS00 at 0x300500 (irq = 9) is a 16550A
 ttyS01 at 0x300c00 (irq = 8) is a 16550A
 HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
 N_HDLC line discipline registered.
 RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
 GDMA1_MAC_ADRH -- : 0x00000000
 GDMA1_MAC_ADRL -- : 0x00000000
 Ralink APSoC Ethernet Driver Initilization. v1.60  256 rx/tx descriptors allocated, mtu = 1600!
 GDMA1_MAC_ADRH -- : 0x0000b848
 GDMA1_MAC_ADRL -- : 0x000c4328
 PROC INIT OK!
 rdm_major = 254
 FLASH_API: MAN_ID=C2 DEV_ID=22A8 SIZE=4MB
 physmap flash device: 400000 at bfc00000
  Amd/Fujitsu Extended Query Table v1.1 at 0x0040
 number of CFI chips: 1
 Region0: SectorSize=0x2000 SectorNum=8
 Region1: SectorSize=0x10000 SectorNum=63
 cfi_cmdset_0002: Using word write method.
 cfi_cmdset_0002: Disabling fast programming due to code brokenness.
 Using physmap partition definition
 Creating 4 MTD partitions on "RT2880 SOC Physically mapped flash":
 0x00000000-0x00030000 : "Bootloader"
 mtd: Giving out device 0 to Bootloader
 0x00030000-0x00040000 : "Config "
 mtd: Giving out device 1 to Config 
 0x00040000-0x00050000 : "Factory"
 mtd: Giving out device 2 to Factory
 0x00050000-0x00400000 : "Kernel"
 mtd: Giving out device 3 to Kernel
 NET4: Linux TCP/IP 1.0 for NET4.0
 IP Protocols: ICMP, UDP, TCP, IGMP
 IP: routing cache hash table of 1024 buckets, 8Kbytes
 TCP: Hash tables configured (established 16384 bind 32768)
 GRE over IPv4 tunneling driver
 Linux IP multicast router 0.06 plus PIM-SM
 NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
 NET4: Ethernet Bridge 008 for NET4.0
 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
 All bugs added by David S. Miller <davem@redhat.com>
 RAMDISK: Compressed image found at block 0
 Freeing initrd memory: 1812k freed
 VFS: Mounted root (squashfs filesystem) readonly.
 Mounted devfs on /dev
 Freeing prom memory: 0kb freed
 Freeing unused kernel memory: 92k freed
 console started
 trying to start /sbin/init
 Algorithmics/MIPS FPU Emulator v1.5
 
 init started: BusyBox v1.8.2 (2008-10-30 02:36:26 CST)
 
 starting pid 10, tty '': '/etc_ro/rcS'''
 mount: mounting devpts: called with bogus options
 none on /sys failed: No such device
 mount: mounting none on /proc/bus/usb failed: No such file or directory
 
 starting pid 16, tty '/dev/console': '/bin/sh'
 
 
 BusyBox v1.8.2 (2008-10-30 02:36:26 CST) built-in shell (ash)
 Enter 'help' for a list of built-in commands.
 
 # 
 
 Yes:
 
       ****** WeLoveLinux ****** 
 
  Welcome to ...
 kernel reg pid 14 success .
 
 httpd Reg gpio hook success .
 insmod rt2860v2_ap
 2860 version : 1.9.0.0 (Oct 30 2008)
 
 
 
 === pAd = c0507000, size = 484224 ===
 
 
 <-- RTMPAllocAdapterBlock, Status=0
 ralink_init make_wireless_config rt2860
 ifconfig ra0 0.0.0.0
 RX DESC a8c4d000  size = 2048
 <-- RTMPAllocTxRxRingMemory, Status=0
 1. Phy Mode = 9
 2. Phy Mode = 9
 3. Phy Mode = 9
 ...

ifconfig

 # ifconfig lo
 lo        Link encap:Local Loopback
           inet addr:127.0.0.1  Mask:255.0.0.0
           UP LOOPBACK RUNNING  MTU:16436  Metric:1
           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)


u-Boot

For TFTP from u-Boot the AP has to bo connected to a 10/100M switch (does not work neither on a 10/100/1000M switch nor on a 10M hub).

For FW recovery use option 2 ("Load system code then write to Flash via TFTP.") to download the original FW image (currently U300ARAEN_2.4.15.bin from U300A_EN_2.4.15.zip).


System info • >>
=====Version=====
 # cat /proc/version
 Linux version 2.4.30 (root@linux-r3ht) (gcc version 3.3.6) #1 Thu Oct 30 02:42:35 CST 2008

=====CPU info=====
 # cat /proc/cpuinfo
 system type             : Palmchip Surfboard
 processor               : 0
 cpu model               : unknown V6.12
 BogoMIPS                : 266.24
 wait instruction        : no
 microsecond timers      : yes
 tlb_entries             : 16
 extra interrupt vector  : yes
 hardware watchpoint     : no
 VCED exceptions         : not available
 VCEI exceptions         : not available

=====Meminfo=====
 # cat /proc/meminfo
         total:    used:    free:  shared: buffers:  cached:
 Mem:  13082624 10506240  2576384        0   897024  3710976
 Swap:        0        0        0
 MemTotal:        12776 kB
 MemFree:          2516 kB
 MemShared:           0 kB
 Buffers:           876 kB
 Cached:           3624 kB
 SwapCached:          0 kB
 Active:           2464 kB
 Inactive:         2044 kB
 HighTotal:           0 kB
 HighFree:            0 kB
 LowTotal:        12776 kB
 LowFree:          2516 kB
 SwapTotal:           0 kB
 SwapFree:            0 kB

=====MTD=====
 # cat /proc/mtd
 dev:    size   erasesize  name
 mtd0: 00030000 00010000 "Bootloader"
 mtd1: 00010000 00010000 "Config "
 mtd2: 00010000 00010000 "Factory"
 mtd3: 003b0000 00010000 "Kernel"

=====Interrupts=====
 # cat /proc/interrupts
            CPU0
   3:       1269       Surfboard  eth2
   4:      12078       Surfboard  ra0
   6:      53928       Surfboard  timer
   8:        313       Surfboard  serial
 
 ERR:          0

=====PS=====
# ps
   PID  Uid        VSZ Stat Command
     1 0          1608 S   init
     2 0               SW  [keventd]
     3 0               SWN [ksoftirqd_CPU0]
     4 0               SW  [kswapd]
     5 0               SW  [bdflush]
     6 0               SW  [kupdated]
     7 0               SW  [mtdblockd]
    14 0          1992 S   httpd
    16 0          1616 S   /bin/sh
    19 0               SW  [rtmpWscHandle]
   116 0          1608 S   udhcpc -i br0 -h W300A -s /etc_ro/udhcpc.script -p /v
   125 0          1992 S   httpd
   126 0          1992 S   httpd
   127 0           748 S   wins W300A 192.168.2.90
   134 0          1608 R   ps

=====PCI=====
 # cat /proc/pci
 PCI devices found:
   Bus  0, device   0, function  0:
     Class 0080: PCI device 1814:0802 (rev 1).
       Master Capable.  Latency=255.
       Prefetchable 32 bit memory at 0x0 [0xfffffff].
 # cat /proc/bus/pci/devices
 0000    18140802        0       00000008        00000000        00000000         00000000        00000000        00000000        00000000        1000000000000000        00000000        00000000        00000000        00000000        00000000