Sitecom WL-341 v2

From TechInfoDepot
Jump to navigationJump to search
multiple revisions of this device, use caution
bgn (N300)
wireless router
Sitecom WL-341.jpg
InfoDepot Wiki
3rd Party Firmware
dd-wrt
OpenWrt
Incompatible
Tomato any flavor
Incompatible
Gargoyle
Status Unknown
Platform
BrandModelRev
Sitecom WL-341 v2
FCC ID
Type
wireless router
CPU1
Ralink RT3050
CPU1 Type
MIPS 24KEc
CPU1 Speed
320 MHz 16-bit
Flash1 Chip
Brand? Model?
Flash1 Size
4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br />
RAM1 Size
16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br />
RAM1 Chip
Brand? Model?
ETH chip1
Ralink RT3050
Switch
Ralink RT3050
Ethernet Port Count
1-WAN
4-LAN

802dot11 OUI: none specified

Expansion IF types
none specified
Power
12 VDC, 1 A
Serial Port (UART)
yes
Special Features
ESR9753 ODM
Other
3rd Party Firmware Support
DD-WRT • (List)
Radio 1
Chip1
Ralink RT3050
Wireless interface OUI
none specified
Antenna Connector Type
none specified
MIMO status
2x2:2
Wireless Standard
IEEE 802.11b/g/n
802.11n
up to 300 Mbps
802.11g
up to 54 Mbps
802.11b
up to 11 Mbps
WiFi Operating Frequency
2.4 GHz
 FCC ID
EnGenius ESR-9753U2M-SR97908005
EnGenius ESR6650U2M-SR97908005
Encore ENHWI-3GN3U2M-SR97908005
Encore ENHWI-N3U2M-SR97908005
No Geek Needed NGNHWI-N3U2M-SR97908005
Rosewill RNX-EasyN400U2M-SR97908005
 CPU1 brandRadio1 chip1 brandRadio1 chip2 brand
Sitecom WL-341 v1
Sitecom WL-341 v2RalinkRalink
Sitecom WL-341 v3

For a list of all currently documented Ralink chipsets with specifications, see Ralink.

For a list of all currently documented Sitecom device with specifications, see Sitecom.

300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class


Overview

RT3050 clock speed is 320, overclocled?

Links of Interest

Flashing

Flashing dd-wrt

Supported by dd-wrt as of = ESR9752 v.24 sp2 - build 12527 ?

THIS GUIDE IS ONLY FOR SITECOM WL-341 V2 .002

First of all toggle all screws behind the box.

There are five screws, one hidden behind on the center of the box.

Check for finding it.

Pay attention then toggle the upside of the box with care!

If you want to work well, you must to toggle the board and the antennas.

Personally, i have substituted that -so called- antennas with and external

"true" antenna.

Now chech for 6 soldered pins standing in the bottom left corner,

the first pins is square. On the left of the pins you can read "pwr,gnd,tx,rx"

The square pin is the power,the second is ground,the third is tx and the last is rx.

Don't care the rest of the pins, you need only these!

Now sold with a 25w iron solder 4 cables (i used utp cables) and plug the cables in the right order in the port of your ttl converter (yes, you must to have it,i payed it 5 euro)

Now get a static ip on your pc (192.168.1.57)

Plug utp cable and serial cable to the router and power on.

Now download "putty" and check for a serial use 57600bps 8bit NO FLOW CONTROL (toggle on settings of putty)

get the right number of port COM (COM1,COM2,COM8,COM12....)

Now reboot your router and if is all ok you'll see putty's window animate.

YOu must to check the button "2" at the start of the router for flash to NVRAM from tftp

Now download TFTPD32 and place it in the folder of the firmware dd-wrt.

start tftpd32

now click Y on putty for going on on flashing.

Now write 192.168.1.54 (for assign an ip to the router) and press enter

Now write 192.168.1.57 (your pc) and press enter

enter the name of the firmware checking the case-sensitive words (EnSenao.bin is better to rename before as ensenao.bin)

and press enter

now if oll is right, the router will download the firmware and the flashing will begin

Wait 5 minuter and then use a browser for the address 192.168.1.1

Reverting

Reverting from dd-wrt

The only known method for reverting is flashing original firmware downloaded as for dd-wrt firmware using the same steps.