Keebox W150NR v1/Serial info

From TechInfoDepot
Jump to navigationJump to search
Boot log
U-Boot 1.1.3 (Jan 13 2009 - 17:40:14) (Alpha) - SVN revision : 105

Model: WRGN23

Board: RT2880 DRAM:  32 MB
twe0 set to <NULL>
toe0 set to <NULL>
============================================
Ralink UBoot Version: 3.1 Alpha
--------------------------------------------
ASIC 3052_MP2 (MAC to GigaMAC Mode)
DRAM COMPONENT: 256Mbits
DRAM BUS: 16BIT
Total memory: 32Mbytes
Date:Jan 13 2009  Time:17:40:14
============================================
icache: sets:128, ways:4, linesz:32 ,total:16384
dcache: sets:128, ways:4, linesz:32 ,total:16384

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   9: Load Boot Loader code then write to Flash via TFTP.
You choosed (0)
  0 seconds ...

Eth0 (10/100-M) :  ethaddr = (00:14:d1:7d:19:ea) 00 14 D1 7D 19 EA

3: System Boot system code via Flash.
## Powering down port 0 ~ 3.
## Booting image at bf050000 ...
We have SEAMA, Image Size = 3223584
Verifying Checksum ...
Uncompressing SEAMA linux.lzma ... OK
## Transferring control to Linux (at address bf05000c) ...
## Giving linux memsize in MB, 32

Starting kernel ...

Linux version 2.6.21 (tomcat@enzo) (gcc version 3.3.5) #1 Tue Jun 29 11:41:20 CST 2010

 The CPU feqenuce set to 320 MHz
CPU revision is: 0001964c
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock1 noinitrd
Primary instruction cache 16kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
arch_init_irq: cause = 80800004, status = 1100ff00
PID hash table entries: 128 (order: 7, 512 bytes)
mips_time_init: calculating r4koff ... 0x00138800 (1280000)
CPU frequency 320.00 MHz
Using 160.000 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29080k/32768k available (2546k kernel code, 3688k reserved, 533k data, 120k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered
io scheduler deadline registered (default)
FLASH_API: MAN_ID=1 DEV_ID=7E1A00 SIZE=4MB
rt3052 access driver initialization.
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
ra2880_read_mac: 00:00:00:00:00:00
ra2880_read_mac: 00:00:00:00:00:00
Ralink APSoC Ethernet Driver Initilization. v1.60  256 rx/tx descriptors allocated, mtu = 1536!
ra2880_read_mac: 00:00:00:00:00:00
ra2880_read_mac: 00:00:00:00:00:00
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
elbox physmap platform flash device: 00400000 at bfc00000
elbox-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
elbox-flash.0: the flash image has SEAMA header
elbox-flash.0: squashfs filesystem found at offset 1310784
Creating 8 MTD partitions on "elbox-flash.0":
0x00140060-0x00363060 : "rootfs"
0x00050000-0x003f0000 : "upgrade"
0x00040000-0x00050000 : "devconf"
0x00030000-0x00040000 : "devdata"
0x003f0000-0x00400000 : "langpack"
0x00000000-0x00400000 : "flash"
0x00000000-0x00030000 : "u-boot"
0x00030000-0x00038000 : "boot env"
u32 classifier
    Performance counters on
ip_conntrack version 2.4 (256 buckets, 2048 max) - 240 bytes per conntrack
ip_conntrack_pptp version 3.1 loaded
ip_nat_pptp version 3.0 loaded
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux
ipt_time loading
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 120k freed
init started: BAlgorithmics/MIPS FPU Emulator v1.5
usyBox v1.14.1 (2010-06-29 11:41:45 CST)
starting pid 273, tty '': '/etc/init.d/rcS'
[/etc/init.d/S10init.sh]
[/etc/init.d/S16ipv6.sh]
[/etc/init.d/S19init.sh]
[/etc/init.d/S20init.sh]
DEVCONF: no config data available (ret=-1) !
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!     Uable to read device config.     !!
!! Setting is reset to factory default. !!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
  DEFNODE[/etc/defnodes/S10phyinf.php]
  DEFNODE[/etc/defnodes/S11devdata.xml]
  DEFNODE[/etc/defnodes/S12flashspeed.php]
  DEFNODE[/etc/defnodes/S20device.xml]
  DEFNODE[/etc/defnodes/S22timezone.php]
[/etc/scripts/setdate.sh] 01/01/2000 ...
Sat Jan  1 16:00:02 PST 2000
  DEFNODE[/etc/defnodes/S30device.php]
  DEFNODE[/etc/defnodes/S30device.xml]
  DEFNODE[/etc/defnodes/S31diagnostic.xml]
  DEFNODE[/etc/defnodes/S31locale.php]
  DEFNODE[/etc/defnodes/S32layout.php]
  DEFNODE[/etc/defnodes/S33wifi.php]
  DEFNODE[/etc/defnodes/S40device.xml]
  DEFNODE[/etc/defnodes/S90sessions.php]
  DEFNODE[/etc/defnodes/S90upnpigd.php]
  DEFNODE[/etc/defnodes/S90upnpwfa.php]
SERVD: start service [LOGD]
[/etc/init.d/S20interfaces.sh]
ra2880_read_mac: 00:14:d1:7d:19:eb
Port status change
[/etc/init.d/S45gpiod.sh]
[/etc/init.d/S50config.sh]
[/etc/init.d/rcS] done!
Factory reset time : 3 secs
SERVD: event [WANPORT.LINKDOWN] not found!
[/etc/init0.d/S21layout.sh]: start ...
SERVD: start service [LAYOUT]
[/etc/init0.d/S21wlan.sh]: start ...
[/etc/init0.d/S40event.sh]: start ...
eth2.0: Setting MAC address to  00 14 d1 7d 19 ea.
device eth2 entered promiscuous mode
VLAN (eth2.0):  Setting underlying device (eth2) to promiscious mode.
eth2.2: Setting MAC address to  00 14 d1 7d 19 eb.
VLAN (eth2.2):  Underlying device (eth2) has same MAC, not checking promiscious mode.
eth2.0: dev_set_promiscuity(master, 1)
device eth2.0 entered promiscuous mode
interface ra0 does not exist!
bridge br1 doesn't exist!
SERVD: event [SEALPAC.LOAD/default]
SEAMA: '/dev/mtdblock/5' is not a seama file !
br0: port 1(eth2.0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth2.0) entering forwarding state
[/etc/init0.d/S40gpioevent.sh]: start ...
SERVD: start service [WIFI.WLAN-1]
SERVD: start service [WIFI.WLAN-2]
[/etc/init0.d/S41autowan.sh]: start ...
[/etc/init0.d/S41inf.sh]: start ...
SERVD: start service [LOGD]
SERVD: service [LOGD] is already started.
SERVD: start service [PHYINF.ETH-1]
[/etc/init0.d/S42pthrough.sh]: start ...
[/etc/init0.d/S65ddnsd.sh]: start ...
[/etc/init0.d/S80telnetd.sh]: start ...
[/etc/init0.d/rcS] done!

Please press Enter to activate this console. SERVD: start service [PHYINF.ETH-2]
SIOCSIFHWADDR: Device or resource busy
SERVD: start service [WIFI]
rmmod: can't unload 'rt2860v2_ap': unknown symbol in module, or unknown parameter
rt2860v2_ap: module license 'unspecified' taints kernel.


=== pAd = c0405000, size = 428784 ===

<-- RTMPAllocAdapterBlock, Status=0
RX DESC a1fed000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff 00 00 00 01
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
SYNC - BBP R4 to 20MHz.l
Main bssid = 00:14:d1:7d:19:ea
<==== rt28xx_init, Status=0
0x1300 = 00064380
SERVD: event [WLAN-1.UP/default]
SERVD: event [WLAN-2.UP] not found!
device ra0 entered promiscuous mode
br0: port 2(ra0) entering learning state
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state
br0: port 2(ra0) multicast bandwidth 900kbps
[/etc/scripts/wps.sh] setie ...
Configuration file: /var/servd/hostapd-ra0.conf
Using interface ra0 with hwaddr 00:14:d1:7d:19:ea and ssid 'KEEBOX W150NR'
hostapd_setup_interface: return 0
SERVD: start service [WIFI]
SERVD: service [WIFI] is already started.
SERVD: stop service [MULTICAST]
SERVD: service [MULTICAST] is already stopped.
SERVD: start service [MULTICAST]
SERVD: start service [BRIDGE]
BRIDGE: The device is not in the bridge mode.
SERVD: start service [LAN]
SERVD: start service [WAN]
SERVD: start service [DEVICE.PASSTHROUGH]
SERVD: start service [IPTABLES]
REDSonic turbo net initialized
Network interface reset count v1.0
/proc/sys/net/netfilter/nf_conntrack_udp_timeout: can't create
SERVD: start service [IP6TABLES]
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
ip6tables: not found
SERVD: start service [IPTABLES]
SERVD: service [IPTABLES] is already started.
SERVD: start service [IP6TABLES]
SERVD: service [IP6TABLES] is already started.
SERVD: start service [INET.LAN-1]
[/var/servd/INET.LAN-1_start.sh]: starting LAN-1...
SIOCSIFMTU: No such device
SERVD: event [LAN-1.UP/default]
[/var/servd/INET.LAN-1_start.sh]: starting LAN-1 done !!!
SERVD: start service [IPTMACCTRL]
SERVD: start service [IPTURLCTRL]
SERVD: start service [IPTPORTT]
SERVD: start service [IP6T.LAN-1]
ip6tables: not found
ip6tables: not found
SERVD: start service [IPTABLES]
SERVD: service [IPTABLES] is already started.
SERVD: start service [IP6TABLES]
SERVD: service [IP6TABLES] is already started.
SERVD: start service [INET.WAN-1]
[/var/servd/INET.WAN-1_start.sh]: starting WAN-1...
wireless_event_receive: Malformed netlink message: len=260 left=256 plen=244
[/var/servd/INET.WAN-1_start.sh]: starting WAN-1 done !!!
SERVD: start service [INET.WAN-2]
ifsetup: (WAN-2) not active.
SERVD: service [INET.WAN-2] return error 8.
SERVD: start service [IPTMASQ]
/proc/sys/net/ipv4/ip_personality_sport: can't create
/proc/sys/net/ipv4/ip_personality_enable: can't create
SERVD: start service [IPTVSVR]
SERVD: start service [IPTPFWD]
SERVD: start service [IPTPORTT]
SERVD: service [IPTPORTT] is already started.
SERVD: start service [IPTDMZ]
IPTDMZ: cnt= 1
SERVD: start service [IPT.WAN-1]
SERVD: start service [IP6T.WAN-1]
ip6tables: not found
ip6tables: not found
SERVD: service [IP6T.WAN-1] return error 127.
SERVD: start service [IPT.WAN-2]
SERVD: start service [IP6T.WAN-2]
ip6tables: not found
ip6tables: not found
SERVD: service [IP6T.WAN-2] return error 127.
SERVD: stop service [IPT.LAN-1]
SERVD: service [IPT.LAN-1] is already stopped.
SERVD: start service [IPT.LAN-1]
SERVD: stop service [INFSVCS.LAN-1]
SERVD: service [INFSVCS.LAN-1] is already stopped.
SERVD: start service [INFSVCS.LAN-1]
SERVD: event [INFSVCS.LAN-1.UP/default]
SERVD: event [STATUS.READY/default]
SERVD: start service [HTTP.LAN-1]
SERVD: start service [UPNP.LAN-1]
SERVD: event [UPNP.ALIVE.LAN-1/default]
SERVD: start service [DHCPS4.LAN-1]
SERVD: start service [DNS4.LAN-1]
SERVD: stop service [ROUTE.STATIC]
SERVD: service [ROUTE.STATIC] is already stopped.
SERVD: start service [ROUTE.STATIC]
SERVD: stop service [MULTICAST]
SERVD: start service [MULTICAST]
SERVD: stop service [IPTDEFCHAIN]
SERVD: service [IPTDEFCHAIN] is already stopped.
SERVD: start service [IPTDEFCHAIN]
SERVD: stop service [IP6TDEFCHAIN]
SERVD: service [IP6TDEFCHAIN] is already stopped.
SERVD: start service [IP6TDEFCHAIN]
ip6tables: not found
ip6tables: not found
SERVD: stop service [LLD2]
SERVD: service [LLD2] is already stopped.
SERVD: start service [LLD2]
SERVD: stop service [HTTP]
SERVD: service [HTTP] is already stopped.
SERVD: start service [HTTP]
SERVD: event [HTTP.UP] not found!
SERVD: stop service [DNS]
SERVD: service [DNS] is already stopped.
SERVD: start service [DNS]
killall: dnsmasq: no process killed