DQ Technology VisionNet W203ER-4/serial info

From TechInfoDepot
Jump to navigationJump to search

Info derived from

boot log

Minimal POST completed...     Success.
Last reset cause: Hardware reset (Power-on reset)

PSPBoot1.2 rev: 1.2.1.5
(c) Copyright 2002-2004 Texas Instruments, Inc. All Rights Reserved.

Press ESC for monitor... 1

(psbl)

Booting...
Launching kernel decompressor.
Starting LZMA Uncompression Algorithm.
Copyright (C) 2003 Texas Instruments Incorporated; 
Copyright (C) 1999-2003 Igor Pavlov.
Compressed file is LZMA format.
Kernel decompressor was successful ... launching kernel.

LINUX started...
Config serial console: ttyS0,9600
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 16kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (paul@vserver3) (gcc version 
2.95.3 20010315 (release/MontaVista)) #1 Wed Oct 5 13:27:47 CST 2005
Determined physical RAM map:
 memory: 14000000 @ 00000000 (reserved)
 memory: 00020000 @ 14000000 (ROM data)
 memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 000b71b0(750000)
CPU frequency 150.00 MHz
Calibrating delay loop... 149.91 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 14372k/16384k available (1494k kernel code, 
2012k reserved, 103k data, 60k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 512
Using 512 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
ttyS01 at 0xa8610f00 (irq = 16) is a 16550A
Vlynq CONFIG_MIPS_AVALANCHE_VLYNQ_PORTS=2
Vlynq Device vlynq0 registered with minor no 63 as misc device. Result=0
Vlynq instance:0 Link UP
Vlynq Device vlynq1 registered with minor no 62 as misc device. Result=0
VLYNQ 1 : init failed
block: 64 slots per queue, batch=16
Cpmac driver is allocating buffer memory at init time.
Cpmac driver Disable TX complete interrupt setting threshold to 20.
Default Asymmetric MTU for eth0 1500
PPP generic driver version 2.4.1
avalanche flash device: 0x400000 at 0x10000000.
 Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
Looking for mtd device :mtd0:
Found a mtd0 image (0xa1000), with size (0x35f000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x000a1000-0x00400000 : "mtd0"
mtd: partition "mtd0" doesn't start on an erase block boundary -- force read-only
Looking for mtd device :mtd1:
Found a mtd1 image (0x20090), with size (0x80f70).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020090-0x000a1000 : "mtd1"
mtd: partition "mtd1" doesn't start on an erase block boundary -- force read-only
Looking for mtd device :mtd2:
Found a mtd2 image (0x0), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00000000-0x00010000 : "mtd2"
Looking for mtd device :mtd3:
Found a mtd3 image (0x10000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00010000-0x00020000 : "mtd3"
Looking for mtd device :mtd4:
Found a mtd4 image (0x20000), with size (0x3e0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020000-0x00400000 : "mtd4"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.0 (128 buckets, 1024 max) - 364 bytes per conntrack
ip_tables: (c)2000 Netfilter core team
netfilter PSD loaded - (c) astaro AG
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k freed
serial console detected.  Disabling virtual terminals.
console=/dev/tts/0
init started:  BusyBox v0.61.pre (2005.10.05-05:30+0000) multi-call binary
Starting pid 9, console /dev/tts/0: '/etc/init.d/rcS'
Algorithmics/MIPS FPU Emulator v1.5
 Reading Standard Configuration File /etc/led.conf

 Configured 15 states
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/atm/tiatm.o
registered device TI Avalanche SAR
Texas Instruments ATM driver: version:[4.03.03.00]
Waiting for enter to start '/bin/sh' (pid 31, terminal /dev/tts/0)

Please press Enter to activate this console. SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Sep  8 12:00:14 cfgmgr(ap): AP is disabled
Sep  8 12:00:14 cfgmgr(pppoe-106): Valid Configuration Tree
PVC dB
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
Doing BRCTL ...
addbr br0
Doing BRCTL ...
addbr br1
Doing BRCTL ...
addbr br2
Sep  8 12:00:14 cfgmgr(snmpcm): snmpd starts (1)
Sep  8 12:00:14 cfgmgr(sntp): NTP Polling Timer for DHCP Started succesfully.
Sep  8 12:00:14 cfgmgr(sar): DSL Polling Timer Started succesfully.
Sep  8 12:00:14 cfgmgr(fdb): Firewall NAT service started
Default Asymmetric MTU for nas0 1500
Sep  8 12:00:16 IP: routing cache hash table of 512 buckets, 4Kbytes
Sep  8 12:00:16 TCP: Hash tables configured (established 1024 bind 1024)
Sep  8 12:00:16 : ip_conntrack version 2.0 (128 buckets, 1024 max) - 364 bytes per conntrack
Sep  8 12:00:16 ip_tables: (c)2000 Netfilter core team
Sep  8 12:00:16 : netfilter PSD loaded - (c) astaro AG
Sep  8 12:00:16 : Initializing the WAN Bridge.
Sep  8 12:00:16 : Please set the MAC Address for the WAN Bridge.
Sep  8 12:00:16 : Set the Environment variable 'wan_br_mac'.
Sep  8 12:00:16 MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
Sep  8 12:00:16 VFS: Mounted root (squashfs filesystem) readonly.
Sep  8 12:00:16 : Mounted devfs on /dev
Sep  8 12:00:16 Freeing unused kernel memory: 60k freed
Sep  8 12:00:16 : Algorithmics/MIPS FPU Emulator v1.5
Sep  8 12:00:16 : registered device TI Avalanche SAR
Sep  8 12:00:16 Texas Instruments ATM driver: version:[4.03.03.00]
Sep  8 12:00:16 : Default Asymmetric MTU for nas0 1500
Sep  8 12:00:16 : Default Asymmetric MTU for br0 1500
Sep  8 12:00:16 cfgmgr(lanbridge0): Bridge Created: br0
Doing BRCTL ...
setfilter br0 0
Doing BRCTL ...
addif br0 eth0
Doing BRCTL ...
addif br0 usb0
Sep  8 12:00:16 cfgmgr(lanbridge1): Bridge Created: br1
Doing BRCTL ...
setfilter br1 0
Sep  8 12:00:17 cfgmgr(lanbridge2): Bridge Created: br2
Doing BRCTL ...
setfilter br2 0
Doing BRCTL ...
stp br0 off
Sep  8 12:00:17 cfgmgr(lanbridge0): Bridge Interface Added: eth0
Doing BRCTL ...
setfilter br0 0
Sep  8 12:00:18 cfgmgr(lanbridge0): Add Bridge Iface Error: 1
Doing BRCTL ...
stp br1 off
Doing BRCTL ...
stp br2 off
Sep  8 12:00:18 : Default Asymmetric MTU for br1 1500
Sep  8 12:00:18 : Default Asymmetric MTU for br2 1500
Sep  8 12:00:24 cfgmgr(sar): DSL Carrier is down

cat /proc/version

# cat /proc/version
Linux version 2.4.17_mvl21-malta-mips_fp_le (paul@vserver3) (gcc version 2.95.3 20010315 (release/MontaVista)) #1 Wed Oct 5 13:27:47 CST 2005

cat /proc/cpuinfo

# cat /proc/cpuinfo
processor               : 0
cpu model               : MIPS 4KEc V4.8
BogoMIPS                : 149.91
wait instruction        : no
microsecond timers      : yes
extra interrupt vector  : yes
hardware watchpoint     : yes
VCED exceptions         : not available
VCEI exceptions         : not available

cat /proc/mtd

# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 0035f000 00010000 "mtd0"
mtd1: 00080f70 00010000 "mtd1"
mtd2: 00010000 00002000 "mtd2"
mtd3: 00010000 00010000 "mtd3"
mtd4: 003e0000 00010000 "mtd4"

ps aux

# ps aux
  PID  Uid     VmSize Stat Command
    1 root       1284 S    init
    2 root            S    [keventd]
    3 root            S    [ksoftirqd_CPU0]
    4 root            S    [kswapd]
    5 root            S    [bdflush]
    6 root            S    [kupdated]
    7 root            S    [mtdblockd]
   29 root       2804 S    /usr/bin/cm_pc
   31 root       1288 S    -sh
   32 root       1308 S    /usr/sbin/thttpd -d /usr/www -u root -p 80 -c /cgi-b
   33 root       3588 S    /usr/bin/cm_logic -m /dev/ticfg -c /etc/config.xml
   56 root        608 S    /usr/bin/cm_klogd /dev/klog
   57 root        700 S    /sbin/dproxy -c /etc/resolv.conf -d
   60 root       1668 S    /usr/sbin/snmpd
  144 root        688 S    /usr/sbin/udhcpd /var/tmp/udhcpd.conf
  200 root        628 S    /sbin/utelnetd
  201 root       1288 S    -sh
  202 root       1284 R    ps aux

cat /proc/meminfo

# cat meminfo
        total:    used:    free:  shared: buffers:  cached:
Mem:  14778368  9900032  4878336        0  1093632  3874816
Swap:        0        0        0
MemTotal:        14432 kB
MemFree:          4764 kB
MemShared:           0 kB
Buffers:          1068 kB
Cached:           3784 kB
SwapCached:          0 kB
Active:           2344 kB
Inactive:         3956 kB
HighTotal:           0 kB
HighFree:            0 kB
LowTotal:        14432 kB
LowFree:          4764 kB
SwapTotal:           0 kB
SwapFree:            0 kB

cat /etc/*versions

# cat xaviversions
1.0.0T14_Rev14e.4.2_XW203ER-4
051103
BYS_localhost.localdomain
# cat versions
BUILD=
VERSION=3.6.0A
BOARD=AR7WRD
FSSTAMP=20051005133124

other

cat /etc/led.conf
# cat led.conf
#################################################################
# Configuration File for AR7WRD board
##################################################################
##################################################################
# The GPIO numbers 0 to 31  ==> correspond to GPIO pins  #########
# The GPIO numbers 32,33 are mapped to ADSL (LED) pins ###########
##################################################################


module = adsl    # module = {adsl,usb,pppoe,wlan}
##################################################################
# Note: state 0 for adsl is dummy state and is present only for ##
#       compatibility with the new LED driver                   ##
##################################################################
state   = 0     # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio    = 33    # gpio number
mode    = 0     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash

state   = 1     # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio    = 33    # gpio number
mode    = 0     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash

state   = 2     # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio    = 33    # gpio number
mode    = 4     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1  = 200   # flash on duration in ms
param2  = 200   # flash off duration in ms

state   = 3     # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio    = 33    # gpio number
mode    = 1     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash

state   = 4     # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio    = 32    # gpio number
mode    = 2     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1  = 100    # blink/flash rate in ms
######################################################################
module = cpmac    # module = {adsl,usb,pppoe,wlan,cpmac}

state   = 0     # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio    = 15    # gpio number
mode    = 0     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash


state   = 1     # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio    = 15    # gpio number
mode    = 1     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash

state   = 2     # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio    = 15    # gpio number
mode    = 2     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1  = 100   # blink/flash rate in ms

state   = 3     # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio    = 15    # gpio number
mode    = 2     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1  = 100   # blink/flash rate in ms

#################################################
#module = usb    # module = {adsl,usb,pppoe,wlan}

#state   = 0     # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
#gpio    = 12    # gpio number
#mode    = 0     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash


#state   = 1     # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
#gpio    = 12    # gpio number
#mode    = 1     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash

#state   = 2     # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
#gpio    = 12    # gpio number
#mode    = 2     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
#param1  = 100   # blink/flash rate in ms

#state   = 3     # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
#gpio    = 12    # gpio number
#mode    = 2     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
#param1  = 100   # blink/flash rate in ms

#####################################################################
module = pppoe    # module = {adsl,usb,pppoe,wlan}

state   = 0     # 0 = pppoe down, 1 = pppoe active
gpio    = 13    # gpio number
mode    = 0     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash

state   = 1     # 0 = pppoe down, 1 = pppoe active
gpio    = 13    # gpio number
mode    = 1     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash

######################################################################
module = wlan   # module = {adsl,usb,pppoe,wlan}

state   = 0     # 0 = link down, 1 = link up
gpio    = 6     # gpio number
mode    = 0     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash

state   = 1     # 0 = link down, 1 = link up
gpio    = 6     # gpio number
mode    = 1     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash

state   = 2     # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio    = 6     # gpio number
mode    = 2     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1  = 100   # blink/flash rate in ms

state   = 3     # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio    = 6     # gpio number
mode    = 2     # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1  = 100   # blink/flash rate in ms

nmap 192.168.5.1 -p 1-65535

# nmap 192.168.5.1 -p 1-65535

Starting Nmap 6.40 ( http://nmap.org ) at 2014-04-06 22:03 EDT
Nmap scan report for mygateway1.ar7 (192.168.5.1)
Host is up (0.0050s latency).
Not shown: 65531 closed ports
PORT   STATE SERVICE
21/tcp open  ftp
22/tcp open  ssh
23/tcp open  telnet
80/tcp open  http
MAC Address: 00:01:38:50:8D:BA (XAVi Technologies)

Nmap done: 1 IP address (1 host up) scanned in 32.59 seconds