D-Link DCS-933L rev A2/Serial info
From TechInfoDepot
Jump to navigationJump to searchbootlog
bootlog |
---|
Linux version 2.6.21 (andy@ipcam-linux.alphanetworks.com) (gcc version 3.4.2) #1619 Mon Apr 21 15:07:52 CST 2014 The CPU feqenuce set to 400 MHz CPU revision is: 0001964c Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd On node 0 totalpages: 16384 DMA zone: 128 pages used for memmap DMA zone: 0 pages reserved DMA zone: 16256 pages, LIFO batch:3 Normal zone: 0 pages used for memmap Built 1 zonelists. Total pages: 16256 Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled cause = 40808000, status = 11000000 PID hash table entries: 256 (order: 8, 1024 bytes) calculating r4koff... 00186a00(1600000) CPU frequency 400.00 MHz Using 200.000 MHz high precision timer. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 52016k/65536k available (3126k kernel code, 13456k reserved, 445k data, 5356k init, 0k highmem) Calibrating delay loop... 266.24 BogoMIPS (lpj=532480) Mount-cache hash table entries: 512 NET: Registered protocol family 16 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 Time: MIPS clocksource has been installed. IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered detected lzma initramfs detected lzma initramfs initramfs: LZMA lc=3,lp=0,pb=2,dictSize=33554432,origSize=16699392 LZMA initramfs by Ming-Ching Tiew <mctiew@yahoo.com>.............. ******************** CONFIG_RT2880_ROOTFS_IN_RAM ******************** CONFIG_RT2880_FLASH_8M deice id : 8c 41 17 8c 41 (41178c41) F25L64QA(8c 41178c41) (8192 Kbytes) mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 5 MTD partitions on "raspi": 0x00000000-0x00800000 : "ALL" 0x00000000-0x00030000 : "Bootloader" 0x00030000-0x00040000 : "Config" 0x00040000-0x00050000 : "Factory" 0x00050000-0x00800000 : "Kernel" RT3xxx EHCI/OHCI init. squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro io scheduler noop registered (default) Ralink gpio driver initialized ***** audio_buffer = 808c91ec --- Boot Code Signature --- Signature: DCS-940 932L Release 1.01 (2012-07-12) ===== DCS-933L v1.04 build 1 (2014-04-21) ===== spidrv_major = 217 HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver $Revision: 1.7 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize loop: loaded (max 8 devices) rdm_major = 254 MAC_ADRH -- : 0x00000000 MAC_ADRL -- : 0x00000000 Ralink APSoC Ethernet Driver Initilization. v2.0 256 rx/tx descriptors allocated, mtu = 1500! ***** Init RF/MAC data from flash memory ***** LAN MAC: 28 10 7B 1A 30 28 MAC_ADRH -- : 0x00002810 MAC_ADRL -- : 0x7b1a3028 PROC INIT OK! PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 === pAd = c0019000, size = 533296 === Wlan STA Mode Linux video capture interface: v2.00 block2mtd: version $Revision: 1.1.1.1 $ usbmon: debugfs is not available rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC). ALSA device list: No soundcards found. nf_conntrack version 0.5.0 (512 buckets, 4096 max) ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 5356k freed Algorithmics/MIPS FPU Emulator v1.5 usbcore: registered new interface driver uvcvideo USB Video Class driver (SVN r209) usb 1-1: new high speed USB device using rt3xxx-ehci and address 2 usb 1-1: configuration #1 chosen from 1 choice Found format MJPEG. - 640x480 (30.0 fps) - 320x240 (30.0 fps) - 160x120 (30.0 fps) uvcvideo: Found UVC 1.00 device USB Camera Aoni (05a9:7885) uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround. usbcore: registered new interface driver snd-usb-audio light sensor changed to Night devpts: called with bogus options MJPEG frame count = 10 MJPEG frame size = 131032 H264 frame count = 8 H264 frame size = 184279 light sensor changed to Night SSID: Airmode_Service Cfg PhyMode = 9 Key1Str is Invalid key length(0) or Type(1) Key2Str is Invalid key length(0) or Type(1) Key3Str is Invalid key length(0) or Type(1) Key4Str is Invalid key length(0) or Type(1) HT_BW = BW_20 --> EEPROMAddressNum = 6 WLAN MAC: *****> TxStream = 1, RxStream = 1 Country Region = 80 Phy Mode = 9 MCS Set = ff 00 00 00 00 0x1300 = 00064300 device ra0 entered promiscuous mode device eth2 entered promiscuous mode SSID: Airmode_Service Cfg PhyMode = 9 Key1Str is Invalid key length(0) or Type(1) Key2Str is Invalid key length(0) or Type(1) Key3Str is Invalid key length(0) or Type(1) Key4Str is Invalid key length(0) or Type(1) HT_BW = BW_20 --> EEPROMAddressNum = 6 WLAN MAC: *****> TxStream = 1, RxStream = 1 Country Region = 80 Phy Mode = 9 MCS Set = ff 00 00 00 00 0x1300 = 00064300 br0: port 2(eth2) entering learning state br0: port 1(ra0) entering learning state br0: topology change detected, propagating br0: port 2(eth2) entering forwarding state br0: topology change detected, propagating br0: port 1(ra0) entering forwarding state *** Total SSID = 35 *** site_survey_timer = 142 *** SaveScanTable OK Rcv Wcid(1) AddBAReq Start Seq = 00000000 light sensor changed to Night *** sensor_fps = 30 CIFS VFS: cifs_mount failed w/return code = -6 CIFS VFS: cifs_mount failed w/return code = -6 *** sensor_fps = 15 *** sensor_fps = 30 light sensor changed to Day *** sensor_fps = 15 light sensor changed to Night *** sensor_fps = 30 light sensor changed to Day |
cpuinfo
# cat /proc/cpuinfo system type : Ralink SoC processor : 0 cpu model : MIPS 24K V4.12 BogoMIPS : 266.24 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : yes hardware watchpoint : yes ASEs implemented : mips16 dsp VCED exceptions : not available VCEI exceptions : not available
free
# free -m BusyBox v1.12.1 (2014-04-21 15:01:26 CST) multi-call binary Usage: free # ./busybox free -m total used free shared buffers Mem: 57436 35812 21624 0 0 -/+ buffers: 35812 21624 Swap: 0 0 0