WatchGuard XTM 330 (NC5AE7)/Serial info

Boot log

U-Boot 2011.03 (Jan 20 2012 - 10:52:36) CPU0: P2020E, Version: 2.1, (0x80ea0021) Core: E500, Version: 5.1, (0x80211051) Clock Configuration: CPU0:1066.667 MHz, CPU1:1066.667 MHz, CCB:533.333 MHz, DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), LBC:33.333 MHz L1: D-cache 32 kB enabled I-cache 32 kB enabled Board: P2020RDB XTM330 P2020 334788 Jan 20 2012 I2C: ready DRAM: Configuring DDR for 666.667 MT/s data rate DDR: 1 GiB (DDR3, 32-bit, CL=6, ECC off) Flash: 2 MiB L2: 512 KB enabled NAND: 512 MiB *** Warning - bad CRC, using default environment EEPROM: NXID v0 PCIe1: Root Complex of Slot 2, no link, regs @ 0xffe0a000 PCIe1: Bus 00 - 00 PCIe2: disabled In: serial Out: serial Err: serial Net: eTSEC1: No support for PHY id ffffffff; assuming generic eTSEC3: No support for PHY id ffffffff; assuming generic Init SW10 switch to forwarding mode.... Done Init SW11 switch to forwarding mode.... Done eTSEC1, eTSEC3 WatchGuard WatchGuard U-Boot 2011.03 - 334788 - Jan 20 2012 10:52:36 +-------------------------------------------------------------------------+ |WatchGuard (SYSA) | |WatchGuard (SYSB) | |WatchGuard (SAFE MODE) | | | | | | | | | | | | | | | | | +-------------------------------------------------------------------------+ Use the ^ and v keys to select which entry is highlighted. Press enter to boot the selected OS. Booting SYSA NAND read: device 0 offset 0x20000, size 0x500000 Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 5242880 bytes read: OK WARNING: adjusting available memory to 30000000 ## Booting kernel from FIT Image at 01000000 ... Using 'conf@1' configuration Trying 'kernel@1' kernel subimage Description: WatchGuard Kernel Type: Kernel Image Compression: gzip compressed Data Start: 0x010000cc Data Size: 2893187 Bytes = 2.8 MiB Architecture: PowerPC OS: Linux Load Address: 0x00000000 Entry Point: 0x00000000 Hash algo: crc32 Hash value: d506f72a Hash algo: sha1 Hash value: 41f6386acf750495b481bc591dc5f33019c2711a Verifying Hash Integrity ... crc32+ sha1+ OK ## Flattened Device Tree from FIT Image at 01000000 Using 'conf@1' configuration Trying 'fdt@1' FDT blob subimage Description: Flattened Device Tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x012c2778 Data Size: 11257 Bytes = 11 KiB Architecture: PowerPC Hash algo: crc32 Hash value: 36e5f191 Hash algo: sha1 Hash value: f3896f45217bf769142c10f59ec2ea34798f49ff Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x12c2778 Uncompressing Kernel Image ... OK Loading Device Tree to 00ffa000, end 00fffbf8 ... OK [ 0.000000] Reserving 16MB of memory at 256MB for crashkernel (System RAM: 1024MB) [ 0.000000] Using P2020 RDB machine description [ 0.000000] Memory CAM mapping: 256/256/256/256 Mb, residual: 0Mb [ 0.000000] Linux version 3.0.34 (release@cmfarm02) (gcc version 4.4.5 (WatchGuard Inc./crosstool-ng version: 0.1.5/1.9.0) ) #1 SMP Tue Dec 31 10:48:04 PST 2013 [ 0.000000] CPU maps initialized for 1 thread per core [ 0.000000] bootconsole [udbg0] enabled setup_arch: bootmem mpc85xx_rdb_setup_arch() [ 0.000000] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0 [ 0.000000] PCI host bridge /pcie@ffe0a000 ranges: [ 0.000000] MEM 0x0000000080000000..0x000000009fffffff -> 0x0000000080000000 [ 0.000000] IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000 [ 0.000000] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000 [ 0.000000] MPC85xx RDB board from Freescale Semiconductor arch: exit [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00040000 [ 0.000000] Normal empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00040000 [ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts [ 0.000000] PERCPU: Embedded 7 pages/cpu @a0f03000 s5728 r8192 d14752 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 [ 0.000000] Kernel command line: root=/dev/mtdblock9 rw rootfstype=jffs2 console=ttyS0,115200 ramdisk_size=600000 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1015852k/1048576k available (5668k kernel code, 32724k reserved, 256k data, 1221k bss, 224k init) [ 0.000000] Kernel virtual memory layout: [ 0.000000] * 0xfffdf000..0xfffff000 : fixmap [ 0.000000] * 0xfdfec000..0xfe000000 : early ioremap [ 0.000000] * 0xe1000000..0xfdfec000 : vmalloc & ioremap [ 0.000000] SLUB: Genslabs=15, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:512 [ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs [ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff [ 0.000000] mpic: Initializing for 256 sources [ 0.000000] clocksource: timebase mult[3c00001] shift[22] registered [ 0.000000] Console: colour dummy device 80x25 [ 0.010719] pid_max: default: 32768 minimum: 301 [ 0.015460] Mount-cache hash table entries: 512 [ 0.021315] mpic: requesting IPIs... [ 0.082259] Brought up 2 CPUs [ 0.085704] NET: Registered protocol family 16 [ 0.092124] PCI: Probing PCI hardware [ 0.095764] pci 0000:00:00.0: ignoring class b20 (doesn't match header type 01) [ 0.103052] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.108330] pci 0000:00:00.0: PCI bridge to [bus 01-01] [ 0.113463] pci 0000:00:00.0: bridge window [io 0xfdfed000-0xfdffcfff] [ 0.120221] pci 0000:00:00.0: bridge window [mem 0x80000000-0x9fffffff] [ 0.126982] pci 0000:00:00.0: bridge window [mem pref disabled] [ 0.133055] pci 0000:00:00.0: enabling device (0106 -> 0107) [ 0.140168] bio: create slab <bio-0> at 0 [ 0.144236] Freescale Elo / Elo Plus DMA driver [ 0.148929] SCSI subsystem initialized [ 0.152699] usbcore: registered new interface driver usbfs [ 0.158134] usbcore: registered new interface driver hub [ 0.163441] usbcore: registered new device driver usb [ 0.168693] Switching to clocksource timebase [ 0.173091] FS-Cache: Loaded [ 0.174256] Switched to NOHz mode on CPU #1 [ 0.180045] Switched to NOHz mode on CPU #0 [ 0.184256] CacheFiles: Loaded [ 0.189547] NET: Registered protocol family 2 [ 0.193915] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.201401] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.211117] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.218825] TCP: Hash tables configured (established 131072 bind 65536) [ 0.225355] TCP reno registered [ 0.228465] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.234396] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.241030] NET: Registered protocol family 1 [ 0.246470] fsl-elo-dma ffe0c300.dma: #0 (fsl,eloplus-dma-channel), irq 76 [ 0.253303] fsl-elo-dma ffe0c300.dma: #1 (fsl,eloplus-dma-channel), irq 77 [ 0.260138] fsl-elo-dma ffe0c300.dma: #2 (fsl,eloplus-dma-channel), irq 78 [ 0.266992] fsl-elo-dma ffe0c300.dma: #3 (fsl,eloplus-dma-channel), irq 79 [ 0.274275] fsl-elo-dma ffe21300.dma: #0 (fsl,eloplus-dma-channel), irq 20 [ 0.281097] fsl-elo-dma ffe21300.dma: #1 (fsl,eloplus-dma-channel), irq 21 [ 0.287942] fsl-elo-dma ffe21300.dma: #2 (fsl,eloplus-dma-channel), irq 22 [ 0.294796] fsl-elo-dma ffe21300.dma: #3 (fsl,eloplus-dma-channel), irq 23 [ 0.355038] WG CPU Model 2020 [ 0.358010] WG CRASH MIN RESERVE 0 MB [ 0.376772] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.383941] msgmni has been set to 1986 [ 0.387929] alg: No test for cipher_null (cipher_null-generic) [ 0.393742] alg: No test for ecb(cipher_null) (ecb-cipher_null) [ 0.399636] alg: No test for digest_null (digest_null-generic) [ 0.405442] alg: No test for compress_null (compress_null-generic) [ 0.412813] alg: No test for stdrng (krng) [ 0.416946] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.424251] io scheduler noop registered [ 0.428143] io scheduler deadline registered [ 0.432426] io scheduler cfq registered (default) [ 0.487778] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled [ 0.494606] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A [ 0.501317] console [ttyS0] enabled, bootconsole disabled [ 0.501317] console [ttyS0] enabled, bootconsole disabled [ 0.512467] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A [ 0.519461] Generic non-volatile memory driver v1.1 [ 0.526498] brd: module loaded [ 0.530622] loop: module loaded [ 0.534382] efe00000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002249 [ 0.544386] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.549546] Amd/Fujitsu Extended Query version 1.3. [ 0.554593] number of CFI chips: 1 [ 0.558366] Creating 7 MTD partitions on "efe00000.nor": [ 0.563676] 0x000000000000-0x000000020000 : "NOR (RW) WG CFG0" [ 0.569999] 0x000000020000-0x000000030000 : "NOR (RW) WG CFG1" [ 0.576222] 0x000000030000-0x000000040000 : "NOR (RW) WG MFG DATA" [ 0.582811] 0x000000040000-0x0000000f0000 : "NOR (RW) WG bootOpt Data & reserved" [ 0.590699] 0x0000000f0000-0x000000100000 : "NOR (RW) WG U-Boot ENV" [ 0.597460] 0x000000100000-0x000000180000 : "NOR (RW) WG U-Boot Image" [ 0.604387] 0x000000180000-0x000000200000 : "NOR (RW) WG U-Boot FAILSAFE" [ 0.611785] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB 3,3V 8-bit) [ 0.622293] Creating 7 MTD partitions on "ffa00000.flash": [ 0.627776] 0x000000000000-0x000000020000 : "NAND (RW) WG DTB Image" [ 0.634660] 0x000000020000-0x000000520000 : "NAND (RW) WG SYSA Kernel" [ 0.641596] 0x000000520000-0x000007f00000 : "NAND (RW) WG SYSA_CODE" [ 0.648401] 0x000007f00000-0x00001df00000 : "NAND (RW) WG SYSA_DATA" [ 0.655290] 0x00001df00000-0x00001e400000 : "NAND (RW) WG SYSB Kernel" [ 0.662225] 0x00001e400000-0x00001fc00000 : "NAND (RW) WG SYSB_CODE" [ 0.669011] 0x00001fc00000-0x000020000000 : "NAND (RW) WG KDUMP" [ 0.675421] eLBC NAND device at 0xffa00000, bank 1 [ 0.680867] Fixed MDIO Bus: probed [ 0.684617] eth0: Gianfar Ethernet Controller Version 1.2, 10:56:ca:06:d1:50 [ 0.691663] eth0: Running with NAPI enabled [ 0.695839] eth0: RX BD ring size for Q[0]: 256 [ 0.700364] eth0: TX BD ring size for Q[0]: 256 [ 0.705179] eth1: Gianfar Ethernet Controller Version 1.2, 10:56:ca:06:d1:51 [ 0.712222] eth1: Running with NAPI enabled [ 0.716396] eth1: RX BD ring size for Q[0]: 256 [ 0.720918] eth1: TX BD ring size for Q[0]: 256 [ 0.725737] Freescale PowerQUICC MII Bus: probed [ 0.730514] mdio_bus mdio@ffe24520: error probing PHY at address 17 [ 0.736897] mdio_bus mdio@ffe24520: error probing PHY at address 16 [ 0.743216] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.749876] /soc@ffe00000/usb@22000: Invalid 'dr_mode' property, fallback to host mode [ 0.757843] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller [ 0.764500] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 [ 0.793017] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000 [ 0.808990] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 [ 0.814875] hub 1-0:1.0: USB hub found [ 0.818632] hub 1-0:1.0: 1 port detected [ 0.822757] usbcore: registered new interface driver usbserial [ 0.828613] USB Serial support registered for generic [ 0.833691] usbcore: registered new interface driver usbserial_generic [ 0.840211] usbserial: USB Serial Driver core [ 0.844581] USB Serial support registered for pl2303 [ 0.849583] usbcore: registered new interface driver pl2303 [ 0.855149] pl2303: Prolific PL2303 USB to serial adaptor driver [ 0.861188] i2c /dev entries driver [ 0.864792] mpc-i2c ffe03000.i2c: timeout 1000000 us [ 0.874017] rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6 [ 0.886725] rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0 [ 0.893638] mpc-i2c ffe03100.i2c: timeout 1000000 us [ 0.898822] booke_wdt: powerpc book-e watchdog driver loaded [ 0.904567] EDAC MC: Ver: 2.1.0 [ 0.907790] Freescale(R) MPC85xx EDAC driver, (C) 2006 Montavista Software [ 0.914796] mpc85xx_mc_err_probe: No ECC DIMMs discovered [ 0.920606] EDAC DEVICE0: Giving out device to module 'MPC85xx_edac' controller 'mpc85xx_l2_err': DEV 'mpc85xx_l2_err' (INTERRUPT) [ 0.932422] MPC85xx_edac acquired irq 16 for L2 Err [ 0.937295] MPC85xx_edac L2 err registered [ 0.941770] TCP cubic registered [ 0.944996] Initializing XFRM netlink socket [ 0.949689] NET: Registered protocol family 10 [ 0.954602] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 0.960000] NET: Registered protocol family 17 [ 0.964451] NET: Registered protocol family 15 [ 0.971412] rtc-rs5c372 0-0032: setting system clock to 2021-01-11 14:33:35 UTC (1610375615) [ 1.140998] usb 1-1: new high speed USB device number 2 using fsl-ehci [ 1.279184] hub 1-1:1.0: USB hub found [ 1.283246] hub 1-1:1.0: 2 ports detected [ 2.057775] VFS: Mounted root (jffs2 filesystem) on device 31:9. [ 2.063815] Freeing unused kernel memory: 224k init [ 4.080131] Running /etc/runlevel/1/S02rootrw...Done. [ 4.082632] Running /etc/runlevel/1/S05mproc...Done. [ 4.083946] Running /etc/runlevel/1/S05sysfs...Done. [ 4.085094] Running /etc/runlevel/1/S10armled...Done. [ 4.151797] Running /etc/runlevel/1/S18seed-random...Reseeded random generator [ 4.165510] Done. [ 4.191922] Running /etc/runlevel/2/S10var...Done. [ 4.194010] Running /etc/runlevel/2/S11shm...Done. [ 4.196699] Running /etc/runlevel/2/S13devpts...Done. [ 4.197839] Running /etc/runlevel/2/S14temp...Done. [ 4.199079] Running /etc/runlevel/2/S16pending...Done. [ 4.199628] Running /etc/runlevel/2/S18data...Done. [ 7.038438] Running /etc/runlevel/2/S18hotplug...Done. [ 8.597857] Running /etc/runlevel/2/S18kdump...Done. [ 10.622274] Running /etc/runlevel/2/S19ipv6...disabling IPv6 autoconf for all [ 10.624533] disabling IPv6 autoconf for default [ 10.624707] enable IPv6 forwarding for all [ 10.624861] enable IPv6 forwarding for default [ 10.625021] disabling IPv6 for all [ 10.625146] disabling IPv6 for default [ 10.625277] Done. [ 10.625336] Running /etc/runlevel/2/S20cleanup-dbg...Done. [ 10.625535] Running /etc/runlevel/2/S20sigs...Done. [ 11.474248] Running /etc/runlevel/2/S20usb...[ 11.599857] Initializing USB Mass Storage driver... [ 11.605041] usbcore: registered new interface driver usb-storage [ 11.611054] USB Mass Storage support registered. Done. [ 11.602448] Running /etc/runlevel/2/S20wgbase...[ 11.625221] wgipc: module license 'Watchguard Proprietary' taints kernel. [ 11.632011] Disabling lock debugging due to kernel taint Done. [ 11.629992] Running /etc/runlevel/2/S21eth...[ 11.653089] [ 11.653092] wg_dsa_init: Built Dec 31 2013 10:48:40 P2020 SW 2 Flags 2929 [ 11.653095] [ 11.662872] wg_dsa_init: Rename eth0 -> eth4 [ 11.677124] wg_dsa_init: Rename eth1 -> eth0 [ 11.697101] wg_dsa_init: Rename eth0 -> sw10 [ 11.721446] Distributed Switch Architecture driver version 0.1 [ 11.728456] sw10[0]: detected a Marvell 88E6171 switch [ 12.026744] dsa slave smi: probed [ 12.030103] dsa_slave_create: eth0 Marvell headers enabled, len 16 [ 12.061067] dsa_slave_create: eth1 Marvell headers enabled, len 16 [ 12.091012] dsa_slave_create: eth2 Marvell headers enabled, len 16 [ 12.121793] dsa_slave_create: eth3 Marvell headers enabled, len 16 [ 12.152645] wg_dsa_init: Split sw10 [ 12.156136] wg_dsa_init: Rename eth4 -> sw11 [ 12.170573] sw11[0]: detected a Marvell 88E6171 switch [ 12.463968] dsa slave smi: probed [ 12.467324] dsa_slave_create: eth4 Marvell headers enabled, len 16 [ 12.497914] dsa_slave_create: eth5 Marvell headers enabled, len 16 [ 12.527490] dsa_slave_create: eth6 Marvell headers enabled, len 16 [ 12.558122] wg_dsa_init: Split sw11 [ 14.563881] gfar_init_mac: sw10: L2OFF 2 Pad 8 RCTRL 20807ca [ 14.570620] ADDRCONF(NETDEV_UP): sw10: link is not ready [ 14.576325] gfar_init_mac: sw11: L2OFF 2 Pad 8 RCTRL 20807ca [ 14.583032] ADDRCONF(NETDEV_UP): sw11: link is not ready Done. [ 14.575295] Running /etc/runlevel/2/S22hwmon...[ 14.621768] hwmon_vid: Unknown VRM version of your CPU [ 14.630656] w83793 0-002d: Registered watchdog chardev major 10, minor: 212 Done. [ 14.624658] Running /etc/runlevel/2/S22login...Done. [ 14.625930] Running /etc/runlevel/2/S22rtc...Done. [ 14.633048] Running /etc/runlevel/2/S23pppoe...[ 14.669584] PPP generic driver version 2.4.2 [ 14.693315] PPP MPPE Compression module registered [ 14.702000] PPP Deflate Compression module registered [ 14.710165] NET: Registered protocol family 24 Done. [ 14.710242] Running /etc/runlevel/2/S23sslvpn...[ 14.734452] tun: Universal TUN/TAP device driver, 1.6 [ 14.739526] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> Done. [ 14.734304] Running /etc/runlevel/2/S24l2tpvpn...[ 14.760283] L2TP core driver, V2.0 [ 14.769749] L2TP netlink interface [ 14.783757] PPPoL2TP kernel driver, V2.0 Done. [ 14.774422] Running /etc/runlevel/2/S25wgcfg...[ 16.561006] PHY: 0:02 - Link is Up - 1000/Full [ 16.566419] ADDRCONF(NETDEV_CHANGE): sw10: link becomes ready [ 16.572992] PHY: 0:01 - Link is Up - 1000/Full [ 16.577987] ADDRCONF(NETDEV_CHANGE): sw11: link becomes ready Info: No conversion required from version 11.8.1 to 11.8.1. [ 17.201515] Done. [ 17.201600] Running /etc/runlevel/2/S27cfgcheck...Config ok [ 18.373066] Done. [ 18.373169] Running /etc/runlevel/2/S29firewall...Done. [ 18.375131] Running /etc/runlevel/2/S29wgcore...Done. [ 18.497885] Running /etc/runlevel/2/S30bonding...[ 18.562336] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 18.569490] bonding: MII link monitoring set to 100 ms Done. [ 18.561513] Running /etc/runlevel/2/S30net...[ 18.621713] Bridge firewalling registered [ 18.637545] Ebtables v2.0 registered [ 18.673109] GRE over IPv4 demultiplexor driver [ 18.692499] GRE over IPv4 tunneling driver [ 18.699714] bvpn vif handlers are registered [ 18.721523] 802.1Q VLAN Support v1.8 Done. [ 18.718282] Running /etc/runlevel/2/S30upgrade...Done. [ 18.722685] Running /etc/runlevel/2/S31cacert...Done. [ 18.830825] Running /etc/runlevel/2/S31cert...[ 22.280008] JFFS2 notice: (77) check_node_data: wrong data CRC in data node at 0x0496736c: read 0xa6f6c955, calculated 0xbd0b7942. Done. [ 24.679242] Running /etc/runlevel/2/S31crypto...[ 24.710295] talitos ffe30000.crypto: hwrng [ 24.714533] alg: No test for authenc(hmac(sha1),cbc(aes)) (authenc-hmac-sha1-cbc-aes-talitos) [ 24.723091] talitos ffe30000.crypto: authenc-hmac-sha1-cbc-aes-talitos [ 24.729674] alg: No test for authenc(hmac(sha1),cbc(des3_ede)) (authenc-hmac-sha1-cbc-3des-talitos) [ 24.738759] talitos ffe30000.crypto: authenc-hmac-sha1-cbc-3des-talitos [ 24.745444] alg: No test for authenc(hmac(sha256),cbc(aes)) (authenc-hmac-sha256-cbc-aes-talitos) [ 24.754330] talitos ffe30000.crypto: authenc-hmac-sha256-cbc-aes-talitos [ 24.761107] alg: No test for authenc(hmac(sha256),cbc(des3_ede)) (authenc-hmac-sha256-cbc-3des-talitos) [ 24.770532] talitos ffe30000.crypto: authenc-hmac-sha256-cbc-3des-talitos [ 24.777440] alg: No test for authenc(hmac(md5),cbc(aes)) (authenc-hmac-md5-cbc-aes-talitos) [ 24.785816] talitos ffe30000.crypto: authenc-hmac-md5-cbc-aes-talitos [ 24.792357] alg: No test for authenc(hmac(md5),cbc(des3_ede)) (authenc-hmac-md5-cbc-3des-talitos) [ 24.801259] talitos ffe30000.crypto: authenc-hmac-md5-cbc-3des-talitos [ 24.807913] talitos ffe30000.crypto: cbc-aes-talitos [ 24.813044] talitos ffe30000.crypto: cbc-3des-talitos [ 24.818425] talitos ffe30000.crypto: md5-talitos [ 24.823223] talitos ffe30000.crypto: sha1-talitos [ 24.828078] talitos ffe30000.crypto: sha224-talitos [ 24.833139] talitos ffe30000.crypto: sha256-talitos [ 24.838205] talitos ffe30000.crypto: sha384-talitos [ 24.843268] talitos ffe30000.crypto: sha512-talitos [ 24.848228] alg: No test for authenc(hmac(sha1),cbc(cipher_null)) (authenc-hmac-sha1-cbc-cipher-null-talitos) [ 24.858183] talitos ffe30000.crypto: authenc-hmac-sha1-cbc-cipher-null-talitos [ 24.865467] alg: No test for authenc(hmac(sha256),cbc(cipher_null)) (authenc-hmac-sha256-cbc-cipher-null-talitos) [ 24.875772] talitos ffe30000.crypto: authenc-hmac-sha256-cbc-cipher-null-talitos [ 24.883211] alg: No test for authenc(hmac(sha384),cbc(cipher_null)) (authenc-hmac-sha384-cbc-cipher-null-talitos) [ 24.893475] talitos ffe30000.crypto: authenc-hmac-sha384-cbc-cipher-null-talitos [ 24.900908] alg: No test for authenc(hmac(sha512),cbc(cipher_null)) (authenc-hmac-sha512-cbc-cipher-null-talitos) [ 24.911172] talitos ffe30000.crypto: authenc-hmac-sha512-cbc-cipher-null-talitos [ 24.918618] alg: No test for authenc(hmac(sha384),cbc(aes)) (authenc-hmac-sha384-cbc-aes-talitos) [ 24.927502] talitos ffe30000.crypto: authenc-hmac-sha384-cbc-aes-talitos [ 24.934246] alg: No test for authenc(hmac(sha384),cbc(des3_ede)) (authenc-hmac-sha384-cbc-3des-talitos) [ 24.943642] talitos ffe30000.crypto: authenc-hmac-sha384-cbc-3des-talitos [ 24.950469] alg: No test for authenc(hmac(sha512),cbc(aes)) (authenc-hmac-sha512-cbc-aes-talitos) [ 24.959346] talitos ffe30000.crypto: authenc-hmac-sha512-cbc-aes-talitos [ 24.966093] alg: No test for authenc(hmac(sha512),cbc(des3_ede)) (authenc-hmac-sha512-cbc-3des-talitos) [ 24.975495] talitos ffe30000.crypto: authenc-hmac-sha512-cbc-3des-talitos [ 24.982326] alg: No test for authenc(digest_null,cbc(aes)) (authenc-digest-null-cbc-aes-talitos) [ 24.991131] talitos ffe30000.crypto: authenc-digest-null-cbc-aes-talitos [ 24.997917] alg: No test for authenc(digest_null,cbc(des3_ede)) (authenc-digest-null-cbc-3des-talitos) [ 25.007233] talitos ffe30000.crypto: authenc-digest-null-cbc-3des-talitos [ 25.014078] talitos ffe30000.crypto: ablk-cbc-aes-talitos [ 25.019530] talitos ffe30000.crypto: ablk-cbc-3des-talitos [ 25.025061] alg: No test for auth(sha1) (auth-sha1-talitos) [ 25.030643] talitos ffe30000.crypto: auth-sha1-talitos [ 25.035831] alg: No test for auth(sha256) (auth-sha256-talitos) [ 25.041761] talitos ffe30000.crypto: auth-sha256-talitos [ 25.047119] alg: No test for auth(sha384) (auth-sha384-talitos) [ 25.053049] talitos ffe30000.crypto: auth-sha384-talitos [ 25.058423] alg: No test for auth(sha512) (auth-sha512-talitos) [ 25.064351] talitos ffe30000.crypto: auth-sha512-talitos Done. [ 25.071713] Running /etc/runlevel/2/S31xtables...[ 25.093477] Netfilter messages via NETLINK v0.30. [ 25.109994] ip_set_init[1869]: ip_set: protocol 5 [ 25.278928] nf_conntrack version 0.5.0 (15892 buckets, 63568 max) [ 25.285062] nf_conntrack_init_init_net: conntrack max=63568 high water mark=50854 [ 25.318552] ip_tables: (C) 2000-2006 Netfilter Core Team [ 25.352542] nf_ct_ftp: Maximum expected value 1 [ 25.404467] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 25.411469] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 25.432024] ctnetlink v0.93: registering with nfnetlink. [ 25.547995] arp_tables: (C) 2002 David S. Miller [ 25.640165] u32 classifier [ 25.642929] Performance counters on [ 25.646786] input device check on [ 25.650447] Actions configured Done. [ 25.667755] Running /etc/runlevel/2/S31xtables6...Done. [ 25.696369] Running /etc/runlevel/2/S32auth...Done. [ 25.703742] Running /etc/runlevel/2/S32clst...Done. [ 25.797569] Running /etc/runlevel/2/S32modemdrivers...[ 25.830945] USB Serial support registered for GSM modem (1-port) [ 25.837328] usbcore: registered new interface driver option [ 25.842932] option: v0.7.2:USB Driver for GSM modems [ 25.855957] USB Serial support registered for Sierra USB modem [ 25.862101] usbcore: registered new interface driver sierra [ 25.867685] wg_sierra: v.1.7.40:USB Driver for Sierra Wireless USB modems [ 25.885313] usbcore: registered new interface driver cdc_acm [ 25.890978] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 25.915679] usbcore: registered new interface driver cdc_ether [ 25.928550] usbcore: registered new interface driver rndis_host [ 25.942465] usbcore: registered new interface driver sierra_net Done. [ 25.935217] Running /etc/runlevel/2/S32wgxt...[ 25.966716] ipt_addrpairs_6 v0.1.0: Loading [ 25.991509] xt_session6 : Loading [ 25.994854] xt_session6 : Loaded limit 1000 hash 1024 WG IPC ID 184549376 (0x0B000000) [ 26.046210] ipt_addrpairs: ADDRPAIRS SCALE Set MAX 16384 Entry Max 16384 [ 26.052945] ipt_addrpairs: v1.0.0 Loaded [ 26.099673] xt_ifset: Loaded with set limit 5000 and entry limit 5000 [ 26.107486] xt_classify : Loaded [ 26.113212] xt_master: Loaded [ 26.119129] xt_MASTER: Loaded [ 26.125964] xt_WGTEE: Loaded [ 26.133049] Schedule: Loaded [ 26.137345] xt_POLICY: Loaded [ 26.143345] xt_policy : Loaded [ 26.147855] xt_EXPIRES: Loaded [ 26.153894] xt_IPPRECEDENCE: Loaded [ 26.164862] xt_PKTCACHE: Loaded [ 26.193761] xt_session : Loaded limit 1000 hash 1024 WG IPC ID 92274688 (0x05800000) [ 26.225609] xt_CONNCLASSIFY: Loaded [ 26.230396] xt_connclassify : Loaded [ 26.238197] xt_ipspoof : Loaded [ 26.315054] xt_LBDNAT: Loaded [ 26.336697] xt_MWAN: Loaded [ 26.350322] xt_psd: Loaded [ 26.357565] xt_ipsd: Loaded [ 26.364472] xt_ddos: Loaded [ 26.372814] xt_dos: Loaded [ 26.385307] xt_wgaccount: Loaded [ 26.437699] xt_block : Loaded limit 1000 hash 1024 WG IPC ID 155189248 [ 26.450045] xt_localroute: Loaded [ 26.459131] xt_duplicate: Loaded Done. [ 26.462427] Running /etc/runlevel/2/S33appID...[ 26.662873] WG workqueue: Loaded [ 26.701042] bw driver: Loaded Done. [ 26.690851] Running /etc/runlevel/2/S35proxy...[ 26.715015] Proxy glue: Loaded 10:59:59 (196) Setting the proxy tmpfs size to size=248m. [ 26.734767] Done. [ 26.734889] Running /etc/runlevel/2/S35scand...Done. [ 30.206074] Running /etc/runlevel/2/S36dynroute...Done. [ 30.206885] Running /etc/runlevel/2/S42ssh...Done. [ 30.211099] Running /etc/runlevel/2/S44sysb...Done. [ 30.479721] Running /etc/runlevel/2/S50nettune...Setting IPv4 route garbage collection timeout to 2 minutes [ 30.482259] Setting promote_secondaries to 1 [ 30.482432] Done. [ 30.482491] Running /etc/runlevel/2/S53configdhash...Done. [ 30.482891] Running /etc/runlevel/2/S80seed-random...Saved random seed [ 31.560675] Done. [ 31.560863] Running /etc/runlevel/2/S90kcrashrep...Done. [ 31.562197] Running /etc/runlevel/2/S99igmp...Done. [ 31.563147] Running /etc/runlevel/2/S99rootro...Done. [ 31.567853] Running /etc/runlevel/2/S99setmacs...setting device eth0 to 00:90:7f:a4:e0:f9 [ 31.581433] setting device eth1 to 00:90:7f:a4:e0:fa [ 31.581633] setting device eth2 to 00:90:7f:a4:e0:fb [ 31.581813] setting device eth3 to 00:90:7f:a4:e0:fc [ 31.581993] setting device eth4 to 00:90:7f:a4:e0:fd [ 31.582171] setting device eth5 to 00:90:7f:a4:e0:fe [ 31.582351] setting device eth6 to 00:90:7f:a4:e0:ff [ 31.583266] Done. [ 38.517373] device sw10 entered promiscuous mode [ 38.522707] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 38.951394] xt_connbytes: Forcing CT accounting to be enabled [ 38.989451] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 39.006800] ADDRCONF(NETDEV_UP): eth2: link is not ready [ 39.149289] ADDRCONF(NETDEV_UP): eth3: link is not ready [ 39.189878] ADDRCONF(NETDEV_UP): wgdeth3: link is not ready [ 39.308506] device sw11 entered promiscuous mode [ 39.313945] ADDRCONF(NETDEV_UP): eth4: link is not ready [ 39.319532] device sw11 left promiscuous mode [ 39.357295] device sw11 entered promiscuous mode [ 39.362745] ADDRCONF(NETDEV_UP): wgdeth4: link is not ready [ 39.479727] ADDRCONF(NETDEV_UP): eth5: link is not ready [ 39.493796] ADDRCONF(NETDEV_UP): eth6: link is not ready [ 39.730418] Running /etc/runlevel/4/S51armled...Done. XTM330 login: