Sagemcom F@ST 5280/Serial info

Boot Log

This is the boot log (up to U-Boot) obtained via the UART Port (speed 115200)

Version cfe-rom: 0.8.2 FPS0 J2EP Base: 5.2_03 CFE version 1.0.38-161.184 for BCM94908 (64bit,SP,LE) Build Date: vendredi 6 octobre 2017, 18:20:02 (UTC+0200) (g601671@rmm-1186759) Copyright (C) 2000-2015 Broadcom Corporation. Version cfe-ram: 0.8.2 Boot Strap Register: 0x6fd42 Chip ID: BCM4906_A0, Broadcom B53 Quad Core: 1800MHz Total Memory: 536870912 bytes (512MB) NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes NAND flash device: Spansion S34ML02G1, id 0x01da block 128KB size 262144KB pmc_init:PMC using DQM mode pmc_init:7 0 fe1e044f 3520356 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host/tftp (f/h/c) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Default host ramdisk file name : Default ramdisk store address : Default DTB file name : Board Id : F@ST5280 Number of MAC Addresses (1-64) : 10 Base MAC Address : [removed] PSI Size (1-128) KBytes : 128 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Auxillary File System Size Percent: 0 flow memory allocation (MB) : 14 buffer memory allocation (MB) : 16 DHD 0 memory allocation (MB) : 0 DHD 1 memory allocation (MB) : 0 DHD 2 memory allocation (MB) : 0 WLan Feature : 0x00 Partition 1 Size (MB) : Partition 2 Size (MB) : Partition 3 Size (MB) : Partition 4 Size (MB) (Data) : 4MB Initalizing switch low level hardware. Software Resetting Switch ... Done. Waiting MAC port Rx/Tx to be enabled by hardware ...Done Disable Switch All MAC port Rx/Tx Initializing UBI and starting U-Boot... Looking for UBI... Looking for U-Boot... Found valid GSDF Starting U-Boot from UBI at 0x0000000000080000 U-Boot 2017.05@sc-0.14.2 (Oct 06 2017 - 18:00:03 +0200) sc_f5280 CPU: BCM490x Model: Sagemcom F@ST5280 DRAM: 512 MiB NAND: 256 MiB MMC: ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=2", size 8 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 70, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 51/3, WL threshold: 4096, image sequence number: 49925173 ubi0: available PEBs: 0, total reserved PEBs: 70, PEBs reserved for bad PEB handling: 30 Volume bootenv not found! ** Unable to read env from boot:bootenv ** Using default environment In: serial Out: serial Err: serial Version: 2017.05@sc-0.14.2 Board: F@ST5280 Mode: standard ubi0: detaching mtd1 ubi0: mtd1 is detached ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=2", size 8 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 70, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 51/3, WL threshold: 4096, image sequence number: 49925173 ubi0: available PEBs: 0, total reserved PEBs: 70, PEBs reserved for bad PEB handling: 30 Net: brcmenet Autoboot in 0 seconds. Press <SPACE> to abort.