Planex BRL-04CW-U/Serial info

Boot log copied from the above wiki

!@#$^&*()-+|abcdefghijklmnopqrstuvwxyz. 00.01.19(uClinux) (Aug 31 2006 19:22:07) System Clock Rate: 180MHz, Memory Clock Rate: 130MHz Detected flash size: total 2MB. SDRAM MCR: E2A00000 SDRAM size: 16MB Press 'w' for alpha's web upgrade. Press 'r' to update run image, or 'a' to change config, or 'l' to update loader, or 'g' to load run image without updating Flash, or '2' to enter L2 switch mode(50A), or '3' to enter L2 switch mode(50B) ... ForceRunLoader?=0 ... Loading runtime image ... Imag Start Address =0xbe030000 Find a 7zip self-decompressed kernel image, Just GO! ************************************ [#te9dded3] Powered by Realtek RTL8650B SoC, rev 1 ************************************ [#x7328512] CPU revision is: 0000ff00 Init MMU (16 entries) Primary instruction cache 0kB, linesize 0 bytes. Primary data cache 0kB, linesize 0 bytes. Linux version 2.4.26-uc0 (root@FCompiler) (gcc version 3.3.3) #4 Thu Mar 22 20:20:07 CST 2007 Determined physical RAM map: memory: 01000000 @ 00000000 (usable) NOFS reserved @ 0x80331c80 On node 0 totalpages: 4096 zone(0): 4096 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/mtdblock3 rootfstype=squashfs IRR(0)=c0000000 Calibrating delay loop... 178.99 BogoMIPS Memory: 12928k/16384k available (2273k kernel code, 3456k reserved, 104k data, 88k init, 0k highmem) Dentry cache hash table entries: 2048 (order: 2, 16384 bytes) Inode cache hash table entries: 1024 (order: 1, 8192 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 4096 (order: 2, 16384 bytes) Checking for 'wait' instruction... unavailable. POSIX conformance testing by UNIFIX NEW PCI Driver...isLinuxCompliantEndianMode?=False(Big Endian) [PCI] Reset Bridge ..... Finish! No PCI device exist!! Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SERIAL_PCI enabled ttyS00 at 0xbd011100 (irq = 4) is a 16550A ttyS01 at 0xbd011000 (irq = 3) is a 16550A Probing RTL8651 home gateway controller... Initialize RTL865x ASIC and driver chip name: 8650B, chip revid: 1 Initialize mbuf... creating default 2 interfaces...eth0 IRR(6)=c0040000 eth1 ...OK >>>now is rome 3.4 running ........ PPP generic driver version 2.4.2 PPP BSD Compression module registered Amd/Fujitsu Extended Query Table v1.3 at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling fast programming due to code brokenness. Looking for mtd device mtd1: Found a mtd1 image (0x20000), with size (0x10000). Looking for mtd device mtd2: Found a mtd2 image (0x30000), with size (0x9d4a4). Looking for mtd device mtd3: Found a mtd3 image (0xcd4a4), with size (0x101000). Creating 4 MTD partitions on "Physically mapped flash": 0x00000000-0x00020000 : "ldr" 0x00020000-0x00030000 : "alphafs" 0x00030000-0x000cd4a4 : "kernel" 0x000cd4a4-0x001ce4a4 : "squashfs" usb.c: registered new driver usbdevfs usb.c: registered new driver hub USB configurate change f0000001 host/usb-ohci-rtl865x.c: USB OHCI at membase 0xbd000000, IRQ 1 host/usb-ohci-rtl865x.c: usb- usb.c: new USB bus registered, assigned bus number 1 IRR(1)=f0040000 write minterval 27782edf swap df2e7827 read fminterval 27782edf swap df2e7827 usb dev vender id = 0 usb dev product id = 0 hub.c: USB hub found hub.c: 1 port detected usb.c: registered new driver usblp printer.c: v0.13: USB Printer Device Class driver NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 1024 bind 2048) GRE over IPv4 tunneling driver NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 88k freed IRR(3)=f3040000 initial console created on /dev/tts/1 Shell invoked to run file: /etc/rc Command: #### Stanley dynamic mknode #### Command: mknod /dev/wlchr c 13 0 Command: mknod /dev/ptyp0 c 2 0 Command: mknod /dev/ptyp1 c 2 1 Command: mknod /dev/ptyp2 c 2 2 Command: mknod /dev/ptyp3 c 2 3 Command: mknod /dev/ptyp4 c 2 4 Command: mknod /dev/ptyp5 c 2 5 Command: mknod /dev/ptyp6 c 2 6 Command: mknod /dev/ptyp7 c 2 7 Command: mknod /dev/ptyp8 c 2 8 Command: mknod /dev/ptyp9 c 2 9 Command: mknod /dev/ptypa c 2 10 Command: mknod /dev/ptypb c 2 11 Command: mknod /dev/ptypc c 2 12 Command: mknod /dev/ptypd c 2 13 Command: mknod /dev/ptype c 2 14 Command: mknod /dev/ptypf c 2 15 Command: mknod /dev/tty0 c 4 0 Command: mknod /dev/tty1 c 4 1 Command: mknod /dev/tty2 c 4 2 Command: mknod /dev/tty3 c 4 3 Command: mknod /dev/tty4 c 4 4 Command: mknod /dev/tty5 c 4 5 Command: mknod /dev/ttyS0 c 4 64 Command: mknod /dev/ttyS1 c 4 65 Command: mknod /dev/ttyp0 c 3 0 Command: mknod /dev/ttyp1 c 3 1 Command: mknod /dev/ttyp2 c 3 2 Command: mknod /dev/ttyp3 c 3 3 Command: mknod /dev/ttyp4 c 3 4 Command: mknod /dev/ttyp5 c 3 5 Command: mknod /dev/ttyp6 c 3 6 Command: mknod /dev/ttyp7 c 3 7 Command: mknod /dev/ttyp8 c 3 8 Command: mknod /dev/ttyp9 c 3 9 Command: mknod /dev/ttypa c 3 10 Command: mknod /dev/ttypb c 3 11 Command: mknod /dev/ttypc c 3 12 Command: mknod /dev/ttypd c 3 13 Command: mknod /dev/ttype c 3 14 Command: mknod /dev/ttypf c 3 15 Command: mknod /dev/video0 c 81 0 Command: mknod /dev/usblp0 c 180 0 Command: mknod /dev/node c 254 0 Command: mknod /dev/node1 c 254 1 Command: #### end dynamic mknode #### Command: mount -t proc proc /proc Command: mount -t ramfs ramfs /var Command: mount -t usbdevfs none /proc/bus/usb Command: mkdir /var/tmp Command: mkdir /var/ppp/ Command: mkdir /var/log Command: mkdir /var/run Command: mkdir /var/lock Command: mkdir /var/flash Command: mkdir /var/usbmnt Command: mkdir /var/webcam Command: mkdir /var/spool Command: mkdir /var/spool/lpd Command: mkdir /var/spool/lpd/lp0 Command: mkdir /var/spool/lpd/lp1 Command: mkdir /var/spool/lpd/lp2 Command: mkdir /var/spool/lpd/lp3 Command: # add hostname for lprng. Command: # /etc/hosts also need have same name. Command: hostname alpharg Command: #lpd Command: #iwcontrol is required for RTL8185 Wireless driver Command: #iwcontrol auth & Command: Command: #busybox insmod /lib/modules/2.4.26-uc0/kernel/drivers/usb/quickcam.o Command: Command: /bin/webs -u root -d /www -i /var/run/thttpd.pid & [14] Command: Command: #ifconfig wlan0 up promisc Command: Command: Command: Command: Execution Finished, Exiting Sash command shell (version 1.1.1) /> System initializing...Check the crc=0xbadc0e0e,file_des->chksum=0xbadc0e0e! Config info: table total size[49520|0xc170] === max[196608|0x30000]! rtl8651_user_pid set to 14 WAN/LAN, Rx shift=10002 ================runDNSProxy================== session 0 do not have dns server ip... [21] cfg wan to dhcp client ... Set IGMP Default Upstream interface (eth0) ... SUCCESS!! info, client (v0.9.9-pre) started [27] [29] url filter default set to accept PPPoE Passthru disabled. Drop Unknown PPPoE PADT disabled. IPv6 Passthru disabled. IPX Passthru disabled. NETBIOS Passthru disabled. WebRemoteAccessCset? drule=0 onfig signature error !! signature error !! /www/Status/st_blocked.htm: No such file or directory [32] get lan ip c0a80101 enable 1 my host is =router.home=the printer cmdline=lpd -I eth1 -Z 1 -U 1 &! [34] interface: eth1 config : /var/neap.conf get vendor = ALPHA get model = BRL-04CW-U get version = v0.5.0 get secret = password eth1: ip:192.168.1.1, mask:255.255.255.0, mac 00:90:cc:xx:yy:zz eth1 (ip) = 192.168.1.1, (netmask) = 255.255.255.0, adapter index 3 adapter hardware address 00:90:cc:xx:yy:zz Into Server listen!! [36] 2000/1/1 9:0 day=6 info, server (v0.9.9-pre) started error, max_leases value (254) not sane, setting to 31 instead error, Unable to open /var/udhcpd.leases for reading nothing to monitor [40] dir = /www shiang(34): Set_lpd_pid(5) shiang_lpd:s=515, Lpd_listen_port_DYN=(null), Lpd_port_DYN=515 shiang_Ipp:s=off, Ipp_listen_port_DYN=off shiang_Unix:s=/var/run/lprng, Unix_socket_path_DYN=/var/run/lprng 41: the pid_str=41 pofd 17 17! 41: jobQueue_Init success! 41: Into printer_Hotplug_Action()! 41: After reset pDev_Queue, we check each entries! dhcpc client deconfig ifCfgParam?[0].ipAddr: 0.0.0.0 ifCfgParam?[0].ipMask: 0.0.0.0 ifCfgParam?[0].gwAddr: 0.0.0.0 ifCfgParam?[0].dnsPrimaryAddr?: 0.0.0.0 rtl8651_delNaptMapping?: ret -6 rtl8651_delRoute(default): ret -3 rtl8651_delIpIntf?: ret -2710 target 239.0.0.0 SIOCDELRT: No such process debug, Sending select for 192.168.10.225... 41: pclose! 41: create socket success! 41:The unix socket file path=/var/run/pof.d p9100d daemon server in .. after fork .. info, Lease of 192.168.10.225 obtained, lease time 259200 ip 192.168.10.225 router 192.168.10.254 subnet 255.255.255.0 ifCfgParam?[0].ipAddr: 0.0.0.0 ifCfgParam?[0].ipMask: 0.0.0.0 ifCfgParam?[0].gwAddr: 0.0.0.0 ifCfgParam?[0].dnsPrimaryAddr?: 0.0.0.0 rtl8651_delNaptMapping?: ret -6 rtl8651_delRoute(default): ret -3 rtl8651_delIpIntf?: ret -2710 target 239.0.0.0 SIOCDELRT: No such process target default ifCfgParam?[0].ipAddr: 192.168.10.225 ifCfgParam?[0].ipMask: 255.255.255.0 ifCfgParam?[0].gwAddr: 192.168.10.254 ifCfgParam?[0].dnsPrimaryAddr?: 192.168.10.1 *** /bin/msntp ntp3.jst.mfeed.ad.jp &[51] [#e72e4aef] ================runDNSProxy================== [53] error, max_leases value (254) not sane, setting to 31 instead ==== MSNTP simple version, cilent only ==== sntp operation : op_client, count:1 accept:0, count:1, attempts:1 ######################################### got ntp time is :2008 Jun 24 19:51:57.646 ######################################### [55] 2008 Jun 24 19:51:57.646 Process ok