Pheenet WAP-654G/Serial info
From TechInfoDepot
Jump to navigationJump to searchBoot log |
---|
UART1 output test ok Uart init mfid=000000c2 devid=00002249 Found 1 x 2M flash memory ---RealTek(RTL8186)at 2006.02.20-12:02+0800 version 1.4a [16bit](180MHz) no sys signature at 00010000! Jump to image start=0x80350000... decompressing kernel: Uncompressing Linux... done, booting the kernel. done decompressing kernel. early printk enabled Determined physical RAM map: memory: 00800000 @ 00000000 (usable) Initial ramdisk at: 0x80173000 (1843200 bytes) On node 0 totalpages: 2048 zone(0): 2048 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/ram console=0 ramdisk_start=0 single Calibrating delay loop... 178.99 BogoMIPS Memory: 4628k/8192k available (1292k kernel code, 3564k reserved, 1932k data, 44k init, 0k highmem) Dentry-cache hash table entries: 1024 (order: 1, 8192 bytes) Inode-cache hash table entries: 512 (order: 0, 4096 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 2048 (order: 1, 8192 bytes) check_wait... unavailable. POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Serial driver version 6.02 (2003-03-12) with no serial options enabled ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1 state->flags=00000000 Realtek GPIO Driver for Flash Reload Default block: 64 slots per queue, batch=16 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize RealTek E-Flash System Driver. (C) 2002 RealTek Corp. Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000 RTL8185 driver version 1.11 (2006-08-01) 8186NIC Ethernet driver v0.0.5 (Mar 3, 2006) eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4 eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5 NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 512 bind 1024) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NET4: Ethernet Bridge 008 for NET4.0 RAMDISK: ext2 filesystem found at block 0 RAMDISK: Loading 1800 blocks [1 disk] into ram disk... done. Freeing initrd memory: 1800k freed VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 44k freed mount /proc file system ok! serial console detected. Disabling virtual terminals. init started: BusyBox v1.00-pre8 (2005.09.16-02:17+0000) multi-call binary BusyBox v1.00-pre8 (2005.09.16-02:17+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Initialize wlan0 interface killall: syslogd: no process killed killall: klogd: no process killed SIOCGIFFLAGS: No such device bridge br0 doesn't exist; can't delete it Setup bridge... device eth0 entered promiscuous mode eth0:phy is 8201 SIOCDELRT: No such process device wlan0 entered promiscuous mode SIOCDELRT: No such process br0: port 2(wlan0) entering listening state br0: port 1(eth0) entering listening state br0: port 2(wlan0) entering learning state br0: port 2(wlan0) entering forwarding state br0: topology change detected, propagating br0: port 1(eth0) entering learning state br0: port 1(eth0) entering forwarding state br0: topology change detected, propagating SIOCDELRT: No such process SIOCDELRT: No such process Auto-Discovery (ver 1.01) 342 343 # auth uses obsolete (PF_INET,SOCK_PACKET) IEEE 802.1x (WPA) daemon, version 1.7b |
# cat /proc/version Linux version 2.4.18-MIPS-01.00 (root@lnx103) (gcc version 3.3.3) #5 Thu Aug 10 13:14:01 CST 2006 # cat /proc/cpuinfo system type : Philips Nino processor : 0 cpu model : R3000 V0.0 BogoMIPS : 178.99 wait instruction : no microsecond timers : no tlb_entries : 64 extra interrupt vector : no hardware watchpoint : no VCED exceptions : not available VCEI exceptions : not available ll emulations : 0 sc emulations : 0