U-Boot 2009.08-wndap660_620 (Apr 09 2012 - 09:58:05)
CPU: AMCC PowerPC APM82181 Rev. E at 1000 MHz (PLB=166, OPB=83, EBC=83 MHz)
Security support
Bootstrap Option H - Boot ROM Location I2C (Addr 0x52), booting from NAND
32 kB I-Cache 32 kB D-Cache
Board: WNDAP 620 , PCIE0/Wireless
I2C: ready
DRAM: 128 MB
NAND: 32 MiB
Configure Max Payload 256B
PCIE0: successfully set as root-complex
01 00 168c 0030 0280 ff
Net: RTL8367RB initialize...
Disable VLAN...done
Done
ppc_4xx_eth0
Type run flash_nfs to mount root filesystem over NFS
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x110000, size 0x600000
6291456 bytes read: OK
NAND read: device 0 offset 0x1bd0000, size 0x10000
65536 bytes read: OK
## Booting kernel from Legacy Image at 00600000 ...
Image Name: Linux-2.6.36.2-wndap660_620-WNDA
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2739653 Bytes = 2.6 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01000000
Booting using the fdt blob at 0x1000000
Uncompressing Kernel Image ... OK
Loading Device Tree to 00ffa000, end 00fff881 ... OK
Using PowerPC 44x Platform machine description
Linux version 2.6.36.2-wndap660_620-WNDAP620_V2.0.4 (root@localhost.localdomain) (gcc version 4.3.4 (Buildroot 2010.02) ) #1 Wed Feb 6 11:47:30 IST 2013
Zone PFN ranges:
DMA 0x00000000 -> 0x00000800
Normal empty
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00000800
MMU: Allocated 1088 bytes of context maps for 255 contexts
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 2047
Kernel command line: root=/dev/mtdblock4 rw rootfstype=jffs2 ip=192.168.1.50:192 .168.1.10:192.168.1.1:255.255.255.0::eth0:off panic=1 console=ttyS0,9600 init=/l inuxrc raid=noautodetect
PID hash table entries: 512 (order: -5, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 0, 65536 bytes)
Inode-cache hash table entries: 16384 (order: 0, 65536 bytes)
Memory: 123968k/131072k available (5440k kernel code, 7104k reserved, 448k data, 742k bss, 320k init)
Kernel virtual memory layout:
* 0xfffd0000..0xffff0000 : fixmap
* 0xfd600000..0xfe000000 : consistent mem
* 0xfd600000..0xfd600000 : early ioremap
* 0xd1000000..0xfd600000 : vmalloc & ioremap
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:512
UIC0 (32 IRQ sources) at DCR 0xc0
UIC1 (32 IRQ sources) at DCR 0xd0
UIC2 (32 IRQ sources) at DCR 0xe0
UIC3 (32 IRQ sources) at DCR 0xf0
clocksource: timebase mult[400000] shift[22] registered
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 8192
NET: Registered protocol family 16
OCM1: 32768 Bytes (enabled)
OCM1: 32768 Bytes (non-cached)
OCM1: 0 Bytes (cached)
256k L2-cache enabled
PCIE0: Checking link...
PCIE0: Device detected, waiting for link...
PCIE0: link is up !
PCI host bridge /plb/pciex@d00000000 (primary) ranges:
MEM 0x0000000e00000000..0x0000000e7fffffff -> 0x0000000080000000
MEM 0x0000000f00000000..0x0000000f000fffff -> 0x0000000000000000
IO 0x0000000f80000000..0x0000000f8000ffff -> 0x0000000000000000
Removing ISA hole at 0x0000000f00000000
4xx PCI DMA offset set to 0x00000000
/plb/pciex@d00000000: Legacy ISA memory support enabled
PCIE0: successfully set as root-complex
Max pay load supported =0x8700 max pay load prog 0x2010
PCI: Probing PCI hardware
PCI: Hiding 4xx host bridge resources 0000:40:00.0
pci 0000:40:00.0: PCI bridge to [bus 41-7f]
pci 0000:40:00.0: BAR 8: assigned [mem 0xe00000000-0xe000fffff]
pci 0000:40:00.0: BAR 9: assigned [mem 0xe00100000-0xe001fffff pref]
pci 0000:41:00.0: BAR 0: assigned [mem 0xe00000000-0xe0001ffff 64bit]
pci 0000:41:00.0: BAR 0: set to [mem 0xe00000000-0xe0001ffff 64bit]
(PCI address [0x80000000-0x8001ffff]
pci 0000:41:00.0: BAR 6: assigned [mem 0xe00100000-0xe0010ffff pref]
pci 0000:40:00.0: PCI bridge to [bus 41-7f]
pci 0000:40:00.0: bridge window [io disabled]
pci 0000:40:00.0: bridge window [mem 0xe00000000-0xe000fffff]
pci 0000:40:00.0: bridge window [mem 0xe00100000-0xe001fffff pref]
CPM0: pm-iic-device resource /plb/opb/i2c@ef600700
CPM0: pm-emac-device resource /plb/opb/ethernet@ef600c00
CPM0: pm-monitor-event property not defined
CPM0: DCR at 0x160
CPM: ocm suspend address 0xd1040000
CPM: ocm resume address 0xd1040400
CPM: ocm data address 0xd10407d0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timebase
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 0, 65536 bytes)
TCP established hash table entries: 8192 (order: 0, 65536 bytes)
TCP bind hash table entries: 8192 (order: -1, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 4096 (order: 0, 65536 bytes)
UDP-Lite hash table entries: 4096 (order: 0, 65536 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
setting trigger mode 3 for irq 38 failed (uic_set_irq_type+0x0/0x23c)
setting trigger mode 3 for irq 38 failed (uic_set_irq_type+0x0/0x23c)
kcpm: can't read pm-monitor-app
kcpm: unable to parse device tree; aborting
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.29 [Flags: R/O].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.15)
msgmni has been set to 240
Cryptodev Interface Loaded
User space CryptoAPI driver v0.1 loaded
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Generic non-volatile memory driver v1.1
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250.0: ttyS0 at MMIO 0x4ef600300 (irq = 20) is a U6_16550A
console [ttyS0] enabled
4ef600300.serial: ttyS0 at MMIO 0x4ef600300 (irq = 20) is a 16550
brd: module loaded
NAND device: Manufacturer ID: 0xad, Chip ID: 0x75 (SK hynix NAND 32MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 8 MTD partitions on "4e4000000.ndfc.nand":
0x000000000000-0x000002000000 : "NAND 32MiB 3,3V 8-bit"
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000110000 : "u-boot env"
0x000000110000-0x000000710000 : "kernel"
0x000000710000-0x000001bd0000 : "rootfs"
0x000001bd0000-0x000001be0000 : "Device tree"
0x000001be0000-0x000001fe0000 : "var"
0x000001fe0000-0x000002000000 : "Manu data"
PPC 4xx OCP EMAC driver, version 3.54
mal0: descriptor-memory = ocm
MAL: Enabled Interrupt Coal TxCnt: 32 RxCnt: 8
TxTimer: 100000 RxTimer: 5000
MAL v2 /plb/mcmal, 1 TX channels, 1 RX channels
RGMII /plb/opb/emac-rgmii@ef601500 initialized with MDIO support
TAH /plb/opb/emac-tah@ef601350 initialized
/plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
PHY ID: 0xffffff87
RTL8363SB initialize...
Done
eth0: EMAC-0 /plb/opb/ethernet@ef600c00, MAC 90:a4:de:4a:ff:c0
eth0: found Realtek 8363SB Ethernet Switch PHY (0x00)
i2c /dev entries driver
of:ibm-iic 4ef600700.i2c: using standard (100 kHz) mode
of:ibm-iic 4ef600800.i2c: using standard (100 kHz) mode
AMCC 4xx PKA v0.1 @0x04_00114000 size 16384 IRQ 21
Initializing PKA...
PKA Driver Successfully Initialized
oprofile: using timer interrupt.
GACT probability on
Mirror/redirect action on
Simple TC action Loaded
netem: version 1.2
u32 classifier
Performance counters on
input device check on
Actions configured
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
eth0: link is up, 1000 FDX, pause enabled
IP-Config: Complete:
device=eth0, addr=192.168.1.50, mask=255.255.255.0, gw=192.168.1.1,
host=192.168.1.50, domain=, nis-domain=(none),
bootserver=192.168.1.10, rootserver=192.168.1.10, rootpath=
VFS: Mounted root (jffs2 filesystem) on device 31:4.
Freeing unused kernel memory: 320k init
Mounting etc to ramfs. [DONE]
Mounting var tojffs2_scan_dirent_node(): Name CRC failed on
node at 0x001867d8: Read 0xbe20c1ff, calculated 0x44660075
jffs2. rootfs on / type rootfs (rw)
/dev/root on / type jffs2 (rw,relatime)
proc on /proc type proc (rw,relatime)
tmpfs on /tmp type tmpfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,mode=620)
none on /etc type tmpfs (rw,relatime)
[DONE]
Checking SSH keys. [DONE]
Checking for run file. [DONE]
Starting System Logger. [DONE]
Starting Kernel Logger. [DONE]
Erase Total 1 Units
USAGES: wr_mfg_data -w <123> HW Version max 11 chars.
Erase Total 1 Units
## Error: "reginfo" not defined
USAGES: /usr/bin/wr_mfg_data -h for Help.
Checking Manufac. data [DONE]
Checking board file. [CREATED]
Loading Ethernet module. [DONE]
Checking database. [DONE]
Verifing checksum. [DONE]
Loading Bridge module. sh: yes: unknown operand
[DONE]
Loading wlan modules. sh: yes: unknown operand
[DONE]
Creating vap interface. [DONE]
Creating wds interface. [DONE]
Starting configd. [DONE]
Starting web server. [DONE]
Starting Translator... start-stop-daemon: cannot start /usr/bin/log_ro: No such file or directory
[syslog]
Starting Translator... [password]
Starting Translator... [ssh]
Starting Translator... sh: cannot kill pid 606: No such process
[snmp]
Starting Translator... [telnet]
Starting Translator... cat: can't open '/tmp/resolv.conf': No such file or directory
[dns]
Starting Translator... set_dot3_power: Dot3 POE-MDI successfully set for eth0
ip: RTNETLINK answers: No such file or directory
ip: RTNETLINK answers: Invalid argument
ip: RTNETLINK answers: Invalid argument
route: SIOCADDRT: Invalid argument
[bridge_and_vlan_translator]
Starting Translator... [hostapd_tr]
Starting Translator... [qos_translator]
Starting Translator... [nmbd_tr]
Starting Translator... l2_packet_receive - recvfrom: Network is down
l2_packet_receive - recvfrom: Network is down
[http_redirect_tr]
Starting Translator... [dhcp]
Starting Translator... kill: cannot kill pid 1010: No such process
[ntp]
Starting Translator... [timezone]
Sending ARPingARPING to 192.168.0.100 from 192.168.0.100 via brtrunk
Sent 1 probe(s) (1 broadcast(s))
Received 0 reply (0 request(s), 0 broadcast(s))
ARPING to 192.168.0.100 from 192.168.0.100 via brtrunk
Sent 1 probe(s) (1 broadcast(s))
Received 0 reply (0 request(s), 0 broadcast(s))
octl[ATH_HAL_IOCTL_SETPARAM]: Operation not permitted
ioctl[ATH_HAL_IOCTL_SETPARAM]: Operation not permitted
ioctl[ATH_HAL_IOCTL_SETPARAM]: No such device
Welcome to SDK.
Have a lot of fun...
netgear4AFFC8
|