Mercusys MR70X
From TechInfoDepot
Jump to navigationJump to searchabgn+ac+ax (AX1800) | |
|---|---|
| AX1800 Dual-Band Wi-Fi 6 Router | |
 | |
| Homepage | |
| WikiDevi.wi-cat.ru | |
| 3rd Party Firmware | |
| dd-wrt |
Status Unknown |
| OpenWrt | |
| Tomato any flavor |
Incompatible |
| Gargoyle |
Status Unknown |
| Platform | |
| Brand • Model • Rev |
Mercusys MR70X v1.0 |
| FCC ID |
none specified |
| Board ID |
2050501573 |
| Type |
wireless router |
| CPU1 | |
| CPU1 Type |
MIPS 1004Kc |
| CPU1 Speed |
880 MHz ( 2 cores ) 16-bit |
| Flash1 Chip |
Winbond W25Q128JV |
| Flash1 Size |
16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> (SPI NOR) |
| RAM1 Size |
128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR3) |
| RAM1 Chip |
MediaTek MT7621AT |
| ETH chip1 | |
| Switch | |
| Ethernet Port Count |
1-1GbE-WAN 3-1GbE-LAN |
| Wired Standard |
IEEE 802.3i/3u/3ab |
| Stock bootloader |
U-Boot 1.1.3 Ralink UBoot 5.0.0.0 |
| Stock FW OS |
Linux 3.10.108 OpenWrt |
| Expansion IF types |
none specified |
| Power |
12 VDC, 1 A |
| Connector type |
barrel |
| Serial Port (UART) |
yes, 4-pad header, (115200 8N1), J1 |
|
Flags: Wi-Fi 6, MU-MIMO, WPA3, OFDMA, 1024-QAM, TWT | |
| Other | |
|
Default SSID: MERCUSYS_XXXX (1 addl. devices) | |
| 3rd Party Firmware Support | |
| Retail | |
| (Est.) release date | January 2021 |
| EAN |
6957939000509 (UPC DB, On eBay) |
| Country of manuf | China |
| Radio 1 | |
| Chip1 | |
| Chip2 |
MediaTek MT7915D |
| Wireless interface OUI |
C0:25:2F |
| Antenna Connector Type |
soldered |
| MIMO status |
2x2:2 |
| Wireless Standard |
IEEE 802.11b/g/n/ax |
| 802.11ax |
up to 574 Mbps |
| 802.11n |
up to 300 Mbps |
| 802.11g |
up to 54 Mbps |
| 802.11b |
up to 11 Mbps |
| WiFi Operating Frequency |
2.4 GHz |
| Radio 2 | |
| Chip1 | |
| Chip2 |
MediaTek MT7915D |
| Wireless interface OUI |
C0:25:2F |
| Antenna Connector Type |
soldered |
| MIMO status |
2x2:2 |
| Wireless Standard |
IEEE 802.11a/n/ac/ax |
| 802.11ax |
up to 1201 Mbps |
| 802.11ac |
up to 867 Mbps |
| 802.11n |
up to 300 Mbps |
| 802.11a |
up to 54 Mbps |
| WiFi Operating Frequency |
5 GHz |
For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.
For a list of all currently documented Mercusys device with specifications, see Mercusys.
Overview
- 1201Mbps on the 5GHz band and 574Mbps on the 2.4GHz band
- 4× 5dBi Fixed Omni-Directional Antennas
PCB: "E248237 10558", "KB-6160", "2050501573"
Flashing
Flashing OpenWrt
On the OpenWrt ToH (techdata entry)
On the OpenWrt Forum
On the OpenWrt Forum
OpenWrt Target: ramips
OpenWrt Subtarget: mt7621
OpenWrt Package architecture: mipsel_24kc
Support started version: 22.03.4
Current supported version: 23.05.5
On the OpenWrt Forum
On the OpenWrt Forum
OpenWrt Target: ramips
OpenWrt Subtarget: mt7621
OpenWrt Package architecture: mipsel_24kc
Support started version: 22.03.4
Current supported version: 23.05.5
Please insert instructions here
JTAG-Serial Info
Serial
| OEM Boot log (firmware version 1.0.3) |
|---|
U-Boot 1.1.3 (Dec 21 2020 - 16:49:33)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer at: 87f58000
Config XHCI 40M PLL
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:Dec 21 2020 Time:16:49:33
============================================
THIS IS uboot
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =128 Mbytes
Press '4' or 't' to break the booting process
Press 'x' to enter recovery web server
### 0
nm_init:791
nm_initFwupPtnStruct:276
nm_lib_readPtnTable:738
[NM_Debug](nm_lib_readPtnTable) 00743: NM_PTN_TABLE_BASE = 0xfe0000
[NM_Debug](nm_lib_readPtnFromNvram) 00569: partition_used_len = 921, requried len = 8192
[NM_Debug](nm_lib_readPtnTable) 00751: Reading Partition Table from NVRAM ... OK
[NM_Debug](nm_lib_readPtnTable) 00759: Parsing Partition Table ... OK
[NM_Debug](nm_lib_readPtnFromNvram) 00569: partition_used_len = 2, requried len = 2
factory boot check integer ok.
3: System Boot system code via Flash.
## Booting image at bc040000 ...
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 3108392 Bytes = 3 MB
Load Address: 81001000
Entry Point: 816e0af0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 816e0af0) ...
## Giving linux memsize in MB, 128
Starting kernel ...
LINUX started...
THIS IS ASIC
SDK 5.0.S.0
Linux version 3.10.108 (tplink@whattestfortplink) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #5 SMP Tue Dec 22 11:06:12 CST 2020
The CPU feqenuce set to 880 MHz
GCMP present
CPU0 revision is: 0001992f (MIPS 1004Kc)
Software DMA cache coherency
Determined physical RAM map:
memory: 08000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone ranges:
DMA [mem 0x00000000-0x00ffffff]
Normal [mem 0x01000000-0x07ffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x07ffffff]
Detected 3 available secondary CPU(s)
Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
PERCPU: Embedded 7 pages/cpu @81ba8000 s6144 r8192 d14336 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS1,115200 root=/dev/mtdblock2 rootfstype=squashfs init=/etc/preinit mtdparts=raspi:256k(uboot),4096k(uImage),11968k@0x440000(rootfs),64k@0xff0000(ART) mem=128M
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Writing ErrCtl register=000410c2
Readback ErrCtl register=000410c2
Memory: 118912k/131072k available (7077k kernel code, 12160k reserved, 3267k data, 272k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 574.46 BogoMIPS (lpj=1148928)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
launch: starting cpu1
launch: cpu1 gone!
Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU1 revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 1: done.
launch: starting cpu2
launch: cpu2 gone!
Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU2 revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 2: done.
launch: starting cpu3
launch: cpu3 gone!
Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU3 revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 3: done.
Brought up 4 CPUs
NET: Registered protocol family 16
release PCIe RST: RALINK_RSTCTRL = 7000004
PCIE PHY initialize
***** Xtal 40MHz *****
start MT7621 PCIe register access
RALINK_RSTCTRL = 7000004
RALINK_CLKCFG1 = 77ffeff8
*************** MT7621 PCIe RC mode *************
PCIE2 no card, disable it(RST&CLK)
pcie_link status = 0x3
RALINK_RSTCTRL= 3000004
*** Configure Device number setting of Virtual PCI-PCI bridge ***
RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
PCIE0 enabled
PCIE1 enabled
interrupt enable status: 300000
Port 1 N_FTS = 1b105000
Port 0 N_FTS = 1b105000
config reg done
init_rt2880pci done
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 9: assigned [mem 0x60000000-0x601fffff pref]
pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x603fffff pref]
pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff]
pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit pref]
pci 0000:01:00.0: BAR 2: assigned [mem 0x60100000-0x60103fff 64bit pref]
pci 0000:01:00.0: BAR 4: assigned [mem 0x60104000-0x60104fff 64bit pref]
pci 0000:00:00.0: PCI bridge to [bus 01]
pci 0000:00:00.0: bridge window [mem 0x60000000-0x601fffff pref]
pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit pref]
pci 0000:02:00.0: BAR 2: assigned [mem 0x60300000-0x60303fff 64bit pref]
pci 0000:02:00.0: BAR 4: assigned [mem 0x60304000-0x60304fff 64bit pref]
pci 0000:00:01.0: PCI bridge to [bus 02]
pci 0000:00:01.0: bridge window [mem 0x60200000-0x603fffff pref]
PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
BAR0 at slot 1 = 0
bus=0x0, slot = 0x1
bus=0x1, slot = 0x0, irq=0x4
bus=0x2, slot = 0x1, irq=0x18
Switching to clocksource Ralink Systick timer
NET: Registered protocol family 2
Clockevents: could not switch to one-shot mode:
Clockevents: could not switch to one-shot mode:
MIPS is not functional.
MIPS is not functional.
Clockevents: could not switch to one-shot mode: MIPS is not functional.
Could not switch to high resolution mode on CPU 0
Could not switch to high resolution mode on CPU 3
Could not switch to high resolution mode on CPU 2
Clockevents: could not switch to one-shot mode: MIPS is not functional.
Could not switch to high resolution mode on CPU 1
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
Load Kernel WDG Timer Module
Load Ralink Timer0 Module
Load Ralink Timer2 Module
squashfs: version 4.0 (2009/01/31) Phillip Lougher
exFAT: Version 1.2.9
NTFS driver 2.1.30 [Flags: R/W].
msgmni has been set to 232
io scheduler noop registered (default)
reg_int_mask=0, INT_MASK= 0
HSDMA_init
hsdma_phy_tx_ring0 = 0x00c00000, hsdma_tx_ring0 = 0xa0c00000
hsdma_phy_rx_ring0 = 0x00c04000, hsdma_rx_ring0 = 0xa0c04000
TX_CTX_IDX0 = 0
TX_DTX_IDX0 = 0
RX_CRX_IDX0 = 3ff
RX_DRX_IDX0 = 0
set_fe_HSDMA_glo_cfg
HSDMA_GLO_CFG = 465
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
Ralink gpio driver initialized
brd: module loaded
flash manufacture id: ef, device id 40 18
W25Q128BV(ef 40180000) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
4 cmdlinepart partitions found on MTD device raspi
Creating 4 MTD partitions on "raspi":
0x000000000000-0x000000040000 : "uboot"
0x000000040000-0x000000440000 : "uImage"
0x000000440000-0x000000ff0000 : "rootfs"
0x000000ff0000-0x000001000000 : "ART"
Register flash device:flash_chrdev
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
register mt_drv
<--mt7916_hif_init()
pci_data_init: DATA RxRing[0] use DYNAMIC_SLAB_ALLOC buf type
Rx[0] Ring: total 24576 bytes allocated
Rx[1] Ring: total 16384 bytes allocated
<-- pci_alloc_tx_rx_ring_mem, Status=0
=== pAd = c0301000, size = 5926080 ===
<-- RTMPAllocAdapterBlock, Status=0
PCI CSRBaseAddress =0xc0200000, csr_addr=0xc0200000!
RTMPInitPCIeDevice():device_id=0x7915
mt7915_init()-->
Use 0st /etc/MT7915_EEPROM.bin default bin.
Use 1st iPAiLNA default bin.
<--mt7915_init()
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
pci_data_init: DATA RxRing[0] use DYNAMIC_SLAB_ALLOC buf type
pci_data_init: DATA RxRing[1] use DYNAMIC_SLAB_ALLOC buf type
Rx[0] Ring: total 24576 bytes allocated
Rx[1] Ring: total 24576 bytes allocated
Rx[2] Ring: total 8192 bytes allocated
Rx[3] Ring: total 16384 bytes allocated
Rx[4] Ring: total 8192 bytes allocated
<-- pci_alloc_tx_rx_ring_mem, Status=0
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
rdm_major = 253
u32 classifier
input device check on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1858 buckets, 7432 max)
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
ipip: IPv4 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
Type=Linux
TCP: cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
l2tp_core: L2TP core driver, V2.0
l2tp_ip: L2TP IP encapsulation support (L2TPv3)
l2tp_netlink: L2TP netlink interface
l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
8021q: 802.1Q VLAN Support v1.8
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 272K
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -
Please press Enter to activate this console. liblog: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x432880b4
Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x432880a7
PROC INIT OK!
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP MPPE Compression module registered
gre: GRE over IPv4 demultiplexor driver
ip_gre: GRE over IPv4 tunneling driver
NET: Registered protocol family 24
l2tp_ppp: PPPoL2TP kernel driver, V2.0
PPTP driver version 0.8.5
fuse init (API version 7.22)
-------------------------------------------------------------------------------------
reloadprofile() begin
reloadprofile() end
-------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------
reloadconfig() begin
................................start of merge user and default........................
................................parse userconf to get mode.............................
................................end of parse userconf..................................
................................mode : router...............................
................................end of merge user and default..........................
................................new configs merged.....................................
reloadconfig() end
-------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------
FFFFFFB5:FFFFFF85:FFFFFF88:FFFFFFE3:1B:FFFFFFC0
Raeth v3.1 (Tasklet)
set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1
phy_tx_ring = 0x00c48000, tx_ring = 0xa0c48000
phy_rx_ring0 = 0x00c4c000, rx_ring[0] = 0xa0c4c000
phy_rx_ring0 = 0x00c4c000, rx_ring[0] = 0xa0c4c000
MT7530 Reset Timeout!!
change HW-TRAP to 0x17c8f
set TPlink LAN/WAN Partition
set swith-led mode by wj
not turn on phy in gsw ,flag = 0
GMAC1_MAC_ADRH -- : 0x0000000c
GMAC1_MAC_ADRL -- : 0x432880a7
GDMA2_MAC_ADRH -- : 0x0000000c
GDMA2_MAC_ADRL -- : 0x4328809e
eth1: ===> VirtualIF_open
MT7621 GE2 link rate to 1G
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
GDMA2_FWD_CFG = 20710000
1 and 00 and 840
gmtoff: 1:00 and tz: -1:00
GMT-1:00
wireless is starting...
wifi_init
config_profile_set, MacAddress=C0:25:2F:FF:FF:FF>>/etc/wireless/RT2860AP/RT2860_2G.dat
config_profile_set, WscManufacturer=Mercusys>>/etc/wireless/RT2860AP/RT2860_2G.dat
config_profile_set, WscDeviceName=MR70X 1.0.0>>/etc/wireless/RT2860AP/RT2860_2G.dat
config_profile_set, WscModelName=MR70X>>/etc/wireless/RT2860AP/RT2860_2G.dat
config_profile_set, WscModelNumber=1.0.0>>/etc/wireless/RT2860AP/RT2860_2G.dat
config_profile_set, WscSerialNumber=1.0.0>>/etc/wireless/RT2860AP/RT2860_2G.dat
config_profile_set, MacAddress=C0:25:2F:FF:FF:FF>>/etc/wireless/RT2860AP/RT2860_5G.dat
config_profile_set, WscManufacturer=Mercusys>>/etc/wireless/RT2860AP/RT2860_5G.dat
config_profile_set, WscDeviceName=MR70X 1.0.0>>/etc/wireless/RT2860AP/RT2860_5G.dat
config_profile_set, WscModelName=MR70X>>/etc/wireless/RT2860AP/RT2860_5G.dat
config_profile_set, WscModelNumber=1.0.0>>/etc/wireless/RT2860AP/RT2860_5G.dat
config_profile_set, WscSerialNumber=1.0.0>>/etc/wireless/RT2860AP/RT2860_5G.dat
wifi_reload
wifi_radio wifi0
wifi_shutdown_interface wifi0
ifconfig ra0 down
wifi_config_profile wifi0
wifi_config_profile dbdc mode and return
wifi_start_interface wifi0
wifi_vap ra0
wifi_vap dbdc mode
ifconfig ra0 up
ra0: ===> main_virtual_if_open
get_wdev_by_idx: invalid idx(0)
RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
Open file "/etc/wireless/l1profile.dat" Succeed!
load l1profile succeed!
mt_service_open: wlan service opens successfully!
[multi_profile_merge_5g_only] DBDC_MODE=1
multi-profile merge success, en:1,pf1_num:3,pf2_num:3,total:6
Open file "/etc/wireless/RT2860AP/DBDC_card0.dat" to store DBDC cfg! (23)
Write file "/etc/wireless/RT2860AP/DBDC_card0.dat" success (size=8724)!
BssidNum=6
Pf2MbssIdxMap:
0 1 2 3 4 5
MacAddress3 = 00:00:00:00:00:00
E2pAccessMode=2
SSID[0]=MERCUSYS_1124, EdcaIdx=0
SSID[1]=MERCUSYS_Guest_1124, EdcaIdx=0
SSID[2]=, EdcaIdx=0
SSID[3]=MERCUSYS_1124_5G, EdcaIdx=0
SSID[4]=MERCUSYS_Guest_1124_5G, EdcaIdx=0
SSID[5]=, EdcaIdx=0
RTMPSetProfileParameters(): DBDC Mode=1, eDBDC_mode = 1
cfg_mode=16
cfg_mode=16
cfg_mode=16
wmode_band_equal(): Band Equal!
cfg_mode=16
cfg_mode=16
cfg_mode=16
cfg_mode=16
cfg_mode=16
cfg_mode=17
cfg_mode=17
cfg_mode=17
cfg_mode=17
cfg_mode=17
cfg_mode=17
BandSteering=0
BndStrgBssIdx=1;0;0;1;0;0
[TxPower] BAND0: 100, BAND1: 100
[SKUenable] BAND0: 1, BAND1: 1
[SkuTableIdx]: 0
[CCKTxStream] BAND0: 2, BAND1: 0
[PERCENTAGEenable] BAND0: 1, BAND1: 1
[BFBACKOFFenable] BAND0: 0, BAND1: 0
profile: FragThreshold[0]=2346
profile: FragThreshold[1]=2346
profile: FragThreshold[2]=2346
profile: FragThreshold[3]=2346
profile: FragThreshold[4]=2346
profile: FragThreshold[5]=2346
TxBurst=1
APEdca0
Valid=1
APAifsn[0]=3
APAifsn[1]=7
APAifsn[2]=1
APAifsn[3]=1
APEdca1
Valid=1
APAifsn[0]=3
APAifsn[1]=7
APAifsn[2]=1
APAifsn[3]=1
APEdca2
APEdca3
APAifsn[0]=3
APAifsn[1]=7
APAifsn[2]=1
APAifsn[3]=1
APCwmin[0]=4
APCwmin[1]=4
APCwmin[2]=3
APCwmin[3]=2
APCwmax[0]=6
APCwmax[1]=10
APCwmax[2]=4
APCwmax[3]=3
APTxop[0]=0
APTxop[1]=0
APTxop[2]=94
APTxop[3]=47
BSSAifsn[0]=3
BSSAifsn[1]=7
BSSAifsn[2]=2
BSSAifsn[3]=2
BSSAifsn[0]=3
BSSAifsn[1]=7
BSSAifsn[2]=2
BSSAifsn[3]=2
BSSAifsn[0]=3
BSSAifsn[1]=7
BSSAifsn[2]=2
BSSAifsn[3]=2
BSSAifsn[0]=3
BSSAifsn[1]=7
BSSAifsn[2]=2
BSSAifsn[3]=2
BSSAifsn[0]=3
BSSAifsn[1]=7
BSSAifsn[2]=2
BSSAifsn[3]=2
BSSAifsn[0]=3
BSSAifsn[1]=7
BSSAifsn[2]=2
BSSAifsn[3]=2
APSDCapable[0]=0
APSDCapable[1]=0
default ApCliAPSDCapable[0]=0
default ApCliAPSDCapable[1]=0
DfsZeroWait Support=0/0
read_itxbf: ITxBfEn = 1
read_itxbf: BSSID[0]
read_itxbf: MBSS[0] ITxBfEn = 1
read_itxbf: ITxBfEn = 1
read_itxbf: BSSID[1]
read_itxbf: MBSS[1] ITxBfEn = 1
read_itxbf: ITxBfEn = 1
read_itxbf: BSSID[2]
read_itxbf: MBSS[2] ITxBfEn = 1
read_itxbf: ITxBfEn = 1
read_itxbf: BSSID[3]
read_itxbf: MBSS[3] ITxBfEn = 1
read_itxbf: ITxBfEn = 1
read_itxbf: BSSID[4]
read_itxbf: MBSS[4] ITxBfEn = 1
read_itxbf: ITxBfEn = 1
read_itxbf: BSSID[5]
read_itxbf: MBSS[5] ITxBfEn = 1
read_itxbf: Common.ITxBfEn = 1
read_etxbf: ETxBfEnCond = 1
read_etxbf: BSSID[0]
read_etxbf: MBSS[0] ETxBfEnCond = 1
read_etxbf: ETxBfEnCond = 1
read_etxbf: BSSID[1]
read_etxbf: MBSS[1] ETxBfEnCond = 1
read_etxbf: ETxBfEnCond = 1
read_etxbf: BSSID[2]
read_etxbf: MBSS[2] ETxBfEnCond = 1
read_etxbf: ETxBfEnCond = 1
read_etxbf: BSSID[3]
read_etxbf: MBSS[3] ETxBfEnCond = 1
read_etxbf: ETxBfEnCond = 1
read_etxbf: BSSID[4]
read_etxbf: MBSS[4] ETxBfEnCond = 1
read_etxbf: ETxBfEnCond = 1
read_etxbf: BSSID[5]
read_etxbf: MBSS[5] ETxBfEnCond = 1
MBSS[0] MuOfdmaDlEnable = 0
MBSS[1] MuOfdmaDlEnable = 0
MBSS[2] MuOfdmaDlEnable = 0
MBSS[3] MuOfdmaDlEnable = 0
MBSS[4] MuOfdmaDlEnable = 0
MBSS[5] MuOfdmaDlEnable = 0
MBSS[0] MuOfdmaUlEnable = 0
MBSS[1] MuOfdmaUlEnable = 0
MBSS[2] MuOfdmaUlEnable = 0
MBSS[3] MuOfdmaUlEnable = 0
MBSS[4] MuOfdmaUlEnable = 0
MBSS[5] MuOfdmaUlEnable = 0
MBSS[0] MuMimoDlEnable = 0
MBSS[1] MuMimoDlEnable = 0
MBSS[2] MuMimoDlEnable = 0
MBSS[3] MuMimoDlEnable = 0
MBSS[4] MuMimoDlEnable = 0
MBSS[5] MuMimoDlEnable = 0
MBSS[0] MuMimoUlEnable = 0
MBSS[1] MuMimoUlEnable = 0
MBSS[2] MuMimoUlEnable = 0
MBSS[3] MuMimoUlEnable = 0
MBSS[4] MuMimoUlEnable = 0
MBSS[5] MuMimoUlEnable = 0
I/F(ra0) GroupKey ReKeyInterval=86400 seconds
I/F(ra1) GroupKey ReKeyInterval=86400 seconds
I/F(ra2) GroupKey ReKeyInterval=86400 seconds
I/F(ra3) GroupKey ReKeyInterval=86400 seconds
I/F(ra4) GroupKey ReKeyInterval=86400 seconds
I/F(ra5) GroupKey ReKeyInterval=86400 seconds
[PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0
[PMF]Set_PMFMFPC_Proc:: apidx=1, Desired MFPC=0
[PMF]Set_PMFMFPC_Proc:: apidx=2, Desired MFPC=0
[PMF]Set_PMFMFPC_Proc:: apidx=3, Desired MFPC=0
[PMF]Set_PMFMFPC_Proc:: apidx=4, Desired MFPC=0
[PMF]Set_PMFMFPC_Proc:: apidx=5, Desired MFPC=0
[PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0
[PMF]Set_PMFMFPR_Proc:: apidx=1, Desired MFPR=0
[PMF]Set_PMFMFPR_Proc:: apidx=2, Desired MFPR=0
[PMF]Set_PMFMFPR_Proc:: apidx=3, Desired MFPR=0
[PMF]Set_PMFMFPR_Proc:: apidx=4, Desired MFPR=0
[PMF]Set_PMFMFPR_Proc:: apidx=5, Desired MFPR=0
[PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0
[PMF]Set_PMFSHA256_Proc:: apidx=1, Desired PMFSHA256=0
[PMF]Set_PMFSHA256_Proc:: apidx=2, Desired PMFSHA256=0
[PMF]Set_PMFSHA256_Proc:: apidx=3, Desired PMFSHA256=0
[PMF]Set_PMFSHA256_Proc:: apidx=4, Desired PMFSHA256=0
[PMF]Set_PMFSHA256_Proc:: apidx=5, Desired PMFSHA256=0
APCLI[0] ApCliMuOfdmaDlEnable = 0
APCLI[1] ApCliMuOfdmaDlEnable = 0
APCLI[0] ApCliMuOfdmaUlEnable = 0
APCLI[1] ApCliMuOfdmaUlEnable = 0
APCLI[0] ApCliMuMimoDlEnable = 0
APCLI[1] ApCliMuMimoDlEnable = 0
APCLI[0] ApCliMuMimoUlEnable = 0
APCLI[1] ApCliMuMimoUlEnable = 0
IGMP deny list [0]-th entry =224.0.0.1
IGMP deny list [1]-th entry =224.0.0.2
IGMP deny list [2]-th entry =224.0.0.4
IGMP deny list [3]-th entry =224.0.0.5
IGMP deny list [4]-th entry =224.0.0.6
IGMP deny list [5]-th entry =224.0.0.7
IGMP deny list [6]-th entry =224.0.0.8
IGMP deny list [7]-th entry =224.0.0.9
IGMP deny list [8]-th entry =224.0.0.12
IGMP deny list [9]-th entry =224.0.0.16
IGMP deny list [10]-th entry =224.0.0.17
IGMP deny list [11]-th entry =224.0.0.251
IGMP deny list [12]-th entry =224.0.0.252
IGMP deny list [13]-th entry =232.0.0.100
IGMP deny list [14]-th entry =239.255.12.42
IGMP deny list [15]-th entry =239.255.255.250
HT_BAWinSize: wdev[0]: (TX=256, RX=256)
HT_BAWinSize: wdev[1]: (TX=256, RX=256)
HT_BAWinSize: wdev[2]: (TX=256, RX=256)
HT_BAWinSize: wdev[3]: (TX=256, RX=256)
HT_BAWinSize: wdev[4]: (TX=256, RX=256)
HT_BAWinSize: wdev[5]: (TX=256, RX=256)
HT: WDEV[0] Ext Channel = ABOVE
HT: WDEV[1] Ext Channel = ABOVE
HT: WDEV[2] Ext Channel = ABOVE
HT: WDEV[3] Ext Channel = ABOVE
HT: WDEV[4] Ext Channel = ABOVE
HT: WDEV[5] Ext Channel = ABOVE
ChipID=7915, TWTSupport in profile=0
ICapMode = 0
BandIdx = 0, tpcDutyInitFlag=1
BandIdx = 1, tpcDutyInitFlag=1
BandIdx = 0, tpcnitFlag=1
BandIdx = 1, tpcnitFlag=1
BandIdx = 0, tpcDuty=100-60-40-20
BandIdx = 1, tpcDuty=100-60-40-20
BandIdx = 0, thermalHighEn=1
BandIdx = 1, thermalHighEn=1
BandIdx = 0, thermalHighCritera=120
BandIdx = 1, thermalHighCritera=120
BandIdx = 0, thermalLowEn=1
BandIdx = 1, thermalLowEn=1
BandIdx = 0, thermalLowCritera=115
BandIdx = 1, thermalLowCritera=115
BandIdx = 0, thermalRecheckTime=5
BandIdx = 1, thermalRecheckTime=5
BandIdx = 0, thermalRFOffEn=0
BandIdx = 1, thermalRFOffEn=0
BandIdx = 0, thermalRFOffCriteria=125
BandIdx = 1, thermalRFOffCriteria=125
BandIdx = 0, thermalUcType=1
BandIdx = 1, thermalUcType=1
WtcSetMaxStaNum: MaxStaNum:280, BssidNum:6, WdsNum:0, MSTANum:1, MaxNumChipRept:0, MinMcastWcid:281
Top Init Done!
Use alloc_skb
token_tx_two_queues_init(): ct sw token(0) number = 2048
token_tx_two_queues_init(): token que(0) inited done!id_head/tail=0/2048
token_tx_two_queues_init(): 848ba204,848ba204
token_tx_two_queues_init(): ct sw token(1) number = 6144
token_tx_two_queues_init(): token que(1) inited done!id_head/tail=0/6144
token_tx_two_queues_init(): 848ba2ac,848ba2ac
TxRing[0]: attr:0, total 2048 entry initialized
TxRing[1]: attr:0, total 2048 entry initialized
TxRing[2]: attr:0, total 2048 entry initialized
RX[0] DESC a0c10000 size = 24576
RX[1] DESC a0c18000 size = 16384
RX[2] DESC a0c30000 size = 24576
RX[3] DESC a0c38000 size = 24576
RX[4] DESC a0c40000 size = 8192
RX[5] DESC a0c44000 size = 16384
RX[6] DESC a0c42000 size = 8192
-->TX_RING_0[0xd9330]: Attr:0, Base=0xc08000, Cnt=2048!
-->TX_RING_1[0xd5420]: Attr:0, Base=0xc20000, Cnt=2048!
-->TX_RING_2[0xd5430]: Attr:0, Base=0xc28000, Cnt=2048!
-->TX_RING_3[0xd5400]: Attr:3, Base=0xc1c000, Cnt=128!
-->TX_RING_4[0xd5410]: Attr:2, Base=0xc1d000, Cnt=256!
-->TX_RING_5[0xd5440]: Attr:1, Base=0xc1e000, Cnt=256!
-->RX_RING0[0xd8510]: Base=0xc10000, Cnt=1536
-->RX_RING1[0xd9520]: Base=0xc18000, Cnt=1024
-->RX_RING2[0xd4500]: Base=0xc30000, Cnt=1536
-->RX_RING3[0xd4510]: Base=0xc38000, Cnt=10
-->RX_RING4[0xd5500]: Base=0xc40000, Cnt=512
-->RX_RING5[0xd5510]: Base=0xc44000, Cnt=1024
-->RX_RING6[0xd5520]: Base=0xc42000, Cnt=512
Hif Init Done!
pci_driver_own_by_port: success to clear p=0 fw own, from(1): 1 is interrupt mode, 2 is polling mode.
pci_driver_own_by_port: success to clear p=1 fw own, from(1): 1 is interrupt mode, 2 is polling mode.
fw_prepare():using E2 ROM patch
fw_prepare():using E2 RAM
os_load_code_from_bin:#[33mload fw done(/lib/firmware/mt7915_patch_e2_hdr.bin)#[0m
Parsing patch header
Built date: 20200603183652a
Platform: ALPS
HW/SW version: 0x8a108a10
Patch version: 0xffffffff
Section num: 0x2, subsys: 0x4
Section 0: type = 0x30002, offset = 0xe0, size = 0xfc80
Target address: 0x200000, length: 0xfc80
Section 1: type = 0x30002, offset = 0xfd60, size = 0x13610
Target address: 0xe000f000, length: 0x13610
Patch SEM Status = 2
patch is not ready && get semaphore success
Start address = 0x200000, DL length = 64640, Data mode = 0x80000000
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0xe000f000, DL length = 79376, Data mode = 0x80000000
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
MtCmdPatchFinishReq
EventGenericEventHandler: CMD Success
Patch SEM Status = 3
release patch semaphore
#[42m WfMcuHwInit: Before NICLoadFirmware, check ICapMode = 0 #[m
os_load_code_from_bin:#[33mload fw done(/lib/firmware/WIFI_RAM_CODE_7915_E2.bin)#[0m
Parsing CPU 0 fw tailer
Chip ID: 0x0b
Eco version: 0x01
Region number: 0x07
Format version: 0x02
Format flag: 0x01
Ram version: ____000000
Built date: 20200603183730#
Common crc: 0xf8d6dd80
Parsing tailer region 0
Decomp crc: 0x0
Decomp size: 0x0
Decomp block size: 0x0
Target address: 0x21fc00
Download size: 108544
Feature set: 0x20
Parsing tailer region 1
Decomp crc: 0x0
Decomp size: 0x0
Decomp block size: 0x0
Target address: 0x31dc00
Download size: 205824
Feature set: 0x00
Parsing tailer region 2
Decomp crc: 0x0
Decomp size: 0x0
Decomp block size: 0x0
Target address: 0x417400
Download size: 31744
Feature set: 0x00
Parsing tailer region 3
Decomp crc: 0x0
Decomp size: 0x0
Decomp block size: 0x0
Target address: 0xe0022800
Download size: 393216
Feature set: 0x00
Parsing tailer region 4
Decomp crc: 0x0
Decomp size: 0x0
Decomp block size: 0x0
Target address: 0xe0082800
Download size: 350208
Feature set: 0x00
Parsing tailer region 5
Decomp crc: 0x0
Decomp size: 0x0
Decomp block size: 0x0
Target address: 0x23a400
Download size: 89088
Feature set: 0x00
Parsing tailer region 6
Decomp crc: 0x0
Decomp size: 0x0
Decomp block size: 0x0
Target address: 0x400000
Download size: 81920
Feature set: 0x00
Release info: header tag = 0, total length = 80
tag 1, padding length = 0, tag length = 76
payload: t-neptune-MP-TP-Link-AX1800-2015-MT7915_WIFI_RAM_TP-Link_2015-20200603183606
Start address = 0x21fc00, DL length = 108544, Data mode = 0x80000000
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0x31dc00, DL length = 205824, Data mode = 0x80000000
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0x417400, DL length = 31744, Data mode = 0x80000000
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0xe0022800, DL length = 393216, Data mode = 0x80000000
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0xe0082800, DL length = 350208, Data mode = 0x80000000
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0x23a400, DL length = 89088, Data mode = 0x80000000
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0x400000, DL length = 81920, Data mode = 0x80000000
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
MtCmdFwStartReq: override = 0x1, address = 0x21fc00
EventGenericEventHandler: CMD Success
os_load_code_from_bin:#[33mload fw done(/lib/firmware/7915_WACPU_RAM_CODE_release.bin)#[0m
Parsing CPU 1 fw tailer
Chip ID: 0x00
Eco version: 0x01
Region number: 0x03
Format version: 0x02
Format flag: 0x01
Ram version: DEV_000000
Built date: 20200603183749#
Common crc: 0x615f4967
Parsing tailer region 0
Decomp crc: 0x0
Decomp size: 0x0
Decomp block size: 0x0
Target address: 0x10200000
Download size: 82096
Feature set: 0x00
Parsing tailer region 1
Decomp crc: 0x0
Decomp size: 0x0
Decomp block size: 0x0
Target address: 0x10300000
Download size: 16208
Feature set: 0x00
Parsing tailer region 2
Decomp crc: 0x0
Decomp size: 0x0
Decomp block size: 0x0
Target address: 0xe0000000
Download size: 1952
Feature set: 0x00
Release info: header tag = 0, total length = 0
Start address = 0x10200000, DL length = 82096, Data mode = 0x80000010
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0x10300000, DL length = 16208, Data mode = 0x80000010
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0xe0000000, DL length = 1952, Data mode = 0x80000010
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
MtCmdFwStartReq: override = 0x4, address = 0x0
EventGenericEventHandler: CMD Success
MCU Init Done!
efuse_probe: efuse = 10000012
RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=1
RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0xFF0000]
#[42mrtmp_nv_init(): EEPROM Size[3584]#[m
read from offset:0xff0000, len:0xe00, RADIO_SECTOR_START:0xff0000!
validFlashEepromID(): eeFlashId=7915, pAd->ChipID=7915
#[32m[d-die version:1]#[m
#[32m[a-die version:2]#[m
phy schedule try eth1 carrier off reg=0
phy schedule eth1 carrier off
phy schedule try eth1 carrier off reg=0
Country Region from e2p = 0
antenna_default_reset() todo
antenna_default_reset() value = 0x5292, TxPath = 2, RxPath = 2
RTMPReadTxPwrPerRate(458): Don't Support this now!
rc_radio_init(): DBDC MODE=1, ConcurrentBand=2
rc_radio_init(): radio_ctrl=86c79694,Band=0,rfcap=1,channel=1,PhyMode=2 extCha=0xf
rc_radio_init(): radio_ctrl=86c799e8,Band=1,rfcap=2,channel=36,PhyMode=1 extCha=0xf
rcUpdateBandForBFMU PhyCtrl[0].RadioCtrl.IsBfBand = 1
rcUpdateBandForBFMU PhyCtrl[1].RadioCtrl.IsBfBand = 1
TxBfModuleEnCtrl:u1BfNum = 2, u1BfBitmap = 3, u1BfSelBand[0] = 0
ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0
ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0
AntCfgInit(2699): Not support for HIF_MT yet!
mt7915_check_RF_lock_down: RFlockDown Enable: 0
#[34mMtReadPwrLimitTable: sku table idx: 0
#[0mmt7915_check_RF_lock_down: RFlockDown Enable: 0
#[34mMtReadPwrLimitTable: sku table idx: 0
#[0mEEPROM Init Done!
mac_init()-->
init_mac_cr()-->
<--mac_init()
CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
MAC Init Done!
BBPInit():BBP Initialization.....
Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2
Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0
BBPInit() todo
PHY Init Done!
tx_pwr_comp_init():NotSupportYet!
Set_SCSEnable_Proc(): BandIdx=0, SCSEnable=1
MtCmdSetMacTxRx:(ret = 0)
MtCmdSetMacTxRx:(ret = 0)
Main bssid = 00:00:00:00:00:00
MtCmdSetMacTxRx:(ret = 0)
MtCmdSetMacTxRx:(ret = 0)
<==== mt_wifi_init, Status=0
TxBfModuleEnCtrl:u1BfNum = 2, u1BfBitmap = 3, u1BfSelBand[0] = 0
MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 0
MtCmdThermalProtectDutyCfg: duty: 100
MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 1
MtCmdThermalProtectDutyCfg: duty: 60
MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 2
MtCmdThermalProtectDutyCfg: duty: 40
MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 3
MtCmdThermalProtectDutyCfg: duty: 20
mt_wifi_init: Band = 0, dutyLv0 = 100, dutyLv1 = 60, dutyLv2 = 40, dutyLv3 = 20
MtCmdThermalProtectEnable: band_idx: 0, protect_type: 1
MtCmdThermalProtectEnable: trigger_type: 1, trigger_temp: 120
MtCmdThermalProtectEnable: restore_temp: 115, recheck_time: 5
mt_wifi_init: Band = 0, high_en=1, high_thd = 120, low_en = 1, low_thd = 115, RFOFF_en = 0, RFOFF_th = 125, rec_timer = 5, Type = Duty Cycle
MtCmdThermalProtectDutyCfg: band_idx: 1, level_idx: 0
MtCmdThermalProtectDutyCfg: duty: 100
MtCmdThermalProtectDutyCfg: band_idx: 1, level_idx: 1
MtCmdThermalProtectDutyCfg: duty: 60
MtCmdThermalProtectDutyCfg: band_idx: 1, level_idx: 2
MtCmdThermalProtectDutyCfg: duty: 40
MtCmdThermalProtectDutyCfg: band_idx: 1, level_idx: 3
MtCmdThermalProtectDutyCfg: duty: 20
mt_wifi_init: Band = 1, dutyLv0 = 100, dutyLv1 = 60, dutyLv2 = 40, dutyLv3 = 20
MtCmdThermalProtectEnable: band_idx: 1, protect_type: 1
MtCmdThermalProtectEnable: trigger_type: 1, trigger_temp: 120
MtCmdThermalProtectEnable: restore_temp: 115, recheck_time: 5
mt_wifi_init: Band = 1, high_en=1, high_thd = 120, low_en = 1, low_thd = 115, RFOFF_en = 0, RFOFF_th = 125, rec_timer = 5, Type = Duty Cycle
Register MBSSID IF 1 (ra1)
Register MBSSID IF 2 (ra2)
Register MBSSID IF 3 (rax0)
Register MBSSID IF 4 (rax1)
Register MBSSID IF 5 (rax2)
MSTA_Init (2) ---> ApCli
Register MSTA IF (apcli0) , pAd->MSTANum = 1
Caller: SetCommonHT+0xc8/0x1ac
phy_mode=78, ch=6, wdev_type=2
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=0, ampdu_factor=3
Register MSTA IF (apclix0) , pAd->MSTANum = 2
Caller: SetCommonHT+0xc8/0x1ac
phy_mode=177, ch=36, wdev_type=2
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=0, ampdu_factor=3
mt_service_init: wlan service inits successfully!
WtcSetMaxStaNum: MaxStaNum:278, BssidNum:6, WdsNum:0, MSTANum:2, MaxNumChipRept:0, MinMcastWcid:280
RedInit: set CR4/N9 RED Enable to 1.
RedInit: RED Initiailize Done.
cp_support_is_enabled: set Driver CP_SUPPORT to Mode 2.
RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP
wifi_sys_open(), wdev idx = 0
rcUpdateBandForBFMU PhyCtrl[0].RadioCtrl.IsBfBand = 1
rcUpdateBandForBFMU PhyCtrl[1].RadioCtrl.IsBfBand = 1
TxBfModuleEnCtrl:u1BfNum = 2, u1BfBitmap = 3, u1BfSelBand[0] = 0
ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0
ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0
BuildChannelList() BandIdx = 0, PhyMode = 78, ChListNum = 13:
phy_oper_init(): operate TxStream = 2, RxStream = 2
MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0
BW = 1,TXStream = 2, RXStream = 2, scan(0)
MtCmdSetTxRxPath: control_chl = 6,control_ch2=0, central_chl = 4, BW = 1,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(0), Channel_Band = 0
Caller: wlan_operate_init+0xac/0x11c
phy_mode=78, ch=6, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
wdev_attr_update(): wdevId0 = c0:25:2f:ff:ff:ff
AP inf up for ra_0(func_idx) OmacIdx=0
AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn
ApAutoChannelAtBootUp----------------->
ApAutoChannelAtBootUp: AutoChannelBootup[0] = 1
MtCmdSetMacTxRx:(ret = 0)
MtCmdSetMacTxRx:(ret = 0)
MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0
BW = 1,TXStream = 2, RXStream = 2, scan(0)
MtCmdSetTxRxPath: control_chl = 6,control_ch2=0, central_chl = 4, BW = 1,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(0), Channel_Band = 0
ApAutoChannelAtBootUp<-----------------
[PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0
Caller: SetCommonHT+0xc8/0x1ac
phy_mode=78, ch=6, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
wifi_sys_linkup(), wdev idx = 0
wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:287 for WDEV_TYPE:1
LinkToOmacIdx = 0, LinkToWdevType = 1
TRTableInsertMcastEntry:band0 group_idx[0]=0
(bssUpdateChannel), ucPrimCh=6, ucCentChSeg0=4, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1
bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 8320
UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0
MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 1, BandIdx: 0
MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0
MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0
set muru_update_he_cfg()!!!!
SrMbssInit: Spatial Reuse initialize via profile.
PrintSrCmd:
u1CmdSubId = f, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
PrintSrCmd:
u1CmdSubId = 13, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
PrintSrCmd:
u1CmdSubId = 10, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
apidx 0 for WscUUIDInit
Generate UUID for apidx(0)
cancel phy_read_schedule
ra2880stop()...Done
iwpriv ra0 set Seth1: ===> VirtualIF_close
SID=MERCUSYS_0134
Free TX/RX Ring Memory!
iwpriv ra0 set HideSSID=0
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
FFFFFFB5:FFFFFF85:FFFFFF88:FFFFFFE3:1B:FFFFFFC0
Raeth v3.1 (Tasklet)
set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1
phy_tx_ring = 0x00c48000, tx_ring = 0xa0c48000
phy_rx_ring0 = 0x00c4c000, rx_ring[0] = 0xa0c4c000
phy_rx_ring0 = 0x00c4c000, rx_ring[0] = 0xa0c4c000
MT7530 Reset Completed!!
change HW-TRAP to 0x17c8f
set TPlink LAN/WAN Partition
set swith-led mode by wj
not turn on phy in gsw ,flag = 0
GMAC1_MAC_ADRH -- : 0x0000c025
GMAC1_MAC_ADRL -- : 0x2f6f0134
eth1: ===> VirtualIF_open
MT7621 GE2 link rate to 1G
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
GDMA2_FWD_CFG = 20710000
iwpriv ra0 set BeaconPeriod=100
iwpriv ra0 set RTSThreshold=2346
Set_RTSThreshold_Proc: set wdev0 rts length threshold=2346(0x92a)
iwpriv ra0 set FragThreshold=2346
Set_FragThreshold_Proc::set wdev0 FragThreshold=2346)
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
iwpriv ra0 set DGDMA2_MAC_ADRH -- : 0x0000c025
timPeriod=1
GDMA2_MAC_ADRL -- : 0x2f6f0135
GDMA2_MAC_ADRH -- : 0x0000c025
GDMA2_MAC_ADRL -- : 0x2f6f0135
iwpriv ra0 set Weth1: ===> VirtualIF_open
mmCapable=1
IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Caller: SetCommonHT+0xc8/0x1ac
phy_mode=78, ch=6, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
iwpriv ra0 set NoForwarding=0
IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
iwpriv ra0 set NoForwardingBTNBSSID=0
IPv6: ADDRCONF(NETDEV_UP): lo: link is not ready
iwpriv ra0 set UAPSDCapable=1
config_profile_setting_through_iwpriv ra0
iwpriv ra0 set WirelessMode=16
device eth0.2 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.2) entered forwarding state
br-lan: port 1(eth0.2) entered forwarding state
cfg_mode=16
cfg_mode=16
iwpriv ra0 set HtBw=1
iwpriv ra0 set HtBssCoex=1
IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
iwpriv ra0 set ApChannel=0
phy_freq_adjust : no prim_ch value for adjust!
APStop(), oper(1) bssid(0)=c0:25:2f:ff:ff:ff
MacTableResetWdev(2064): MacTableDeleteEntry ff:ff:ff:ff:ff:ff
MacTableDeleteEntry(): wcid 0 =====
ExtEventBeaconLostHandler::FW EVENT (c0:25:2f:ff:ff:ff), Reason 0x10
AP Beacon OFF!!!
wifi_sys_linkdown(), wdev idx = 0
(bssUpdateChannel), ucPrimCh=6, ucCentChSeg0=4, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1
bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0
wifi_sys_close(), wdev idx = 0
APStartUp(), oper(1) bssid(0)=c0:25:2f:ff:ff:ff
wifi_sys_open(), wdev idx = 0
rcUpdateBandForBFMU PhyCtrl[0].RadioCtrl.IsBfBand = 1
rcUpdateBandForBFMU PhyCtrl[1].RadioCtrl.IsBfBand = 1
TxBfModuleEnCtrl:u1BfNum = 2, u1BfBitmap = 3, u1BfSelBand[0] = 0
ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0
ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0
phy_oper_init(): operate TxStream = 2, RxStream = 2
phy_freq_adjust : no prim_ch value for adjust!
Caller: wlan_operate_init+0xac/0x11c
phy_mode=78, ch=0, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
wdev_attr_update(): wdevId0 = c0:25:2f:ff:ff:ff
AP inf up for ra_0(func_idx) OmacIdx=0
AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn
ApAutoChannelAtBootUp----------------->
ApAutoChannelAtBootUp: AutoChannelBootup[0] = 1
MtCmdSetMacTxRx:(ret = 0)
MtCmdSetMacTxRx:(ret = 0)
MtCmdGetChBusyCnt:(ret = 0)
MtCmdChannelSwitch: control_chl = 2,control_ch2=0, central_chl = 2 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 2,control_ch2=0, central_chl = 2, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
MtCmdGetChBusyCnt:(ret = 0)
MtCmdGetChBusyCnt:(ret = 0)
MtCmdChannelSwitch: control_chl = 3,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 3,control_ch2=0, central_chl = 3, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
MtCmdGetChBusyCnt:(ret = 0)
UpdateBeaconHandler, wdev(0) bss not ready (state:0, caller:APMlmePeriodicExec+0x244/0x458)!!
MtCmdGetChBusyCnt:(ret = 0)
MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 4,control_ch2=0, central_chl = 4, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
MtCmdGetChBusyCnt:(ret = 0)
MtCmdGetChBusyCnt:(ret = 0)
MtCmdChannelSwitch: control_chl = 5,control_ch2=0, central_chl = 5 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 5,control_ch2=0, central_chl = 5, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
MtCmdGetChBusyCnt:(ret = 0)
MtCmdGetChBusyCnt:(ret = 0)
MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 6,control_ch2=0, central_chl = 6, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
MtCmdGetChBusyCnt:(ret = 0)
MtCmdGetChBusyCnt:(ret = 0)
MtCmdChannelSwitch: control_chl = 7,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 7,control_ch2=0, central_chl = 7, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
MtCmdGetChBusyCnt:(ret = 0)
MtCmdGetChBusyCnt:(ret = 0)
MtCmdChannelSwitch: control_chl = 8,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 8,control_ch2=0, central_chl = 8, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
MtCmdGetChBusyCnt:(ret = 0)
MtCmdGetChBusyCnt:(ret = 0)
MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 9,control_ch2=0, central_chl = 9, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
MtCmdGetChBusyCnt:(ret = 0)
br-lan: port 1(eth0.2) entered forwarding state
MtCmdGetChBusyCnt:(ret = 0)
MtCmdChannelSwitch: control_chl = 10,control_ch2=0, central_chl = 10 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 10,control_ch2=0, central_chl = 10, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
MtCmdGetChBusyCnt:(ret = 0)
MtCmdGetChBusyCnt:(ret = 0)
====================================================================
Channel 2 : Busy Time = 13667, Skip Channel = FALSE, BwCap = TRUE
Channel 3 : Busy Time = 2220, Skip Channel = FALSE, BwCap = TRUE
Channel 4 : Busy Time = 7046, Skip Channel = FALSE, BwCap = TRUE
Channel 5 : Busy Time = 1190, Skip Channel = FALSE, BwCap = TRUE
Channel 6 : Busy Time = 14263, Skip Channel = FALSE, BwCap = TRUE
Channel 7 : Busy Time = 1305, Skip Channel = FALSE, BwCap = TRUE
Channel 8 : Busy Time = 3690, Skip Channel = FALSE, BwCap = TRUE
Channel 9 : Busy Time = 4994, Skip Channel = FALSE, BwCap = TRUE
Channel 10 : Busy Time = 7584, Skip Channel = FALSE, BwCap = TRUE
====================================================================
Rule 3 Channel Busy time value : Select Primary Channel 5
Rule 3 Channel Busy time value : Min Channel Busy = 1190
Rule 3 Channel Busy time value : BW = 20
[SelectClearChannelBusyTime] - band0 END
ApAutoChannelAtBootUp : Auto channel selection: Selected channel = 5, IsAband = 0
MtCmdChannelSwitch: control_chl = 5,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0
BW = 1,TXStream = 2, RXStream = 2, scan(0)
MtCmdSetTxRxPath: control_chl = 5,control_ch2=0, central_chl = 7, BW = 1,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(0), Channel_Band = 0
ApAutoChannelAtBootUp<-----------------
[PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0
Caller: SetCommonHT+0xc8/0x1ac
phy_mode=78, ch=5, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
wifi_sys_linkup(), wdev idx = 0
wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:287 for WDEV_TYPE:1
LinkToOmacIdx = 0, LinkToWdevType = 1
TRTableInsertMcastEntry:band0 group_idx[0]=0
(bssUpdateChannel), ucPrimCh=5, ucCentChSeg0=7, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1
bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 8320
UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0
MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 1, BandIdx: 0
MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0
MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0
set muru_update_he_cfg()!!!!
SrMbssInit: Spatial Reuse initialize via profile.
PrintSrCmd:
u1CmdSubId = f, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
PrintSrCmd:
u1CmdSubId = 13, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
PrintSrCmd:
u1CmdSubId = 10, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0
u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
apidx 0 for WscUUIDInit
Generate UUID for apidx(0)
Main bssid = c0:25:2f:ff:ff:ff
IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
iwpriv ra0 set AutoChannelSel=3
IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
#[42mSet_AutoChannelSel_Proc: Alg = 3 #[m
Set_AutoChannelSel_Proc, channel != 0, no need to perform ACS!
iwpriv ra0 set MuMimo=1
iwpriv ra0 set MuOfdma=0
iwpriv ra0 set twtsupport=0
iwpriv ra0 set twtEnable=0
iwpriv ra0 set PowerDropCtrl=100
SetPowerDropCtrl: ucPowerDrop = 100
killall -q -SIGINT rt2860apd
iwpriv ra0 set AuthMode=WPA2PSK
iwpriv ra0 set EncrypType=AES
iwpriv ra0 set IEEE8021X=0
iwpriv ra0 set RekeyInterval=0
I/F(ra0) GroupKey ReKeyInterval=0 seconds
iwpriv ra0 set WPAPSK=71378992
iwpriv ra0 set WscConfMode=7
iwpriv ra0 set WscConfStatus=2
iwpriv ra0 set WscVendorPinCode=71378992
iwpriv ra0 set WscLabelDisabled=0
iwpriv ra0 set WscSetupLock=0
iwpriv ra0 set HideSSID=0
iwpriv ra0 set ApSSID=MERCUSYS_0134
[PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0
wifi_sys_linkdown(), wdev idx = 0
ExtEventBeaconLostHandler::FW EVENT (c0:25:2f:ff:ff:ff), Reason 0x10
AP Beacon OFF!!!
(bssUpdateChannel), ucPrimCh=5, ucCentChSeg0=7, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1
bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0
wifi_sys_close(), wdev idx = 0
wifi_sys_open(), wdev idx = 0
rcUpdateBandForBFMU PhyCtrl[0].RadioCtrl.IsBfBand = 1
rcUpdateBandForBFMU PhyCtrl[1].RadioCtrl.IsBfBand = 1
TxBfModuleEnCtrl:u1BfNum = 2, u1BfBitmap = 3, u1BfSelBand[0] = 0
ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0
ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0
phy_oper_init(): operate TxStream = 2, RxStream = 2
MtCmdChannelSwitch: control_chl = 5,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0
BW = 1,TXStream = 2, RXStream = 2, scan(0)
MtCmdSetTxRxPath: control_chl = 5,control_ch2=0, central_chl = 7, BW = 1,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(0), Channel_Band = 0
Caller: wlan_operate_init+0xac/0x11c
phy_mode=78, ch=5, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
wdev_attr_update(): wdevId0 = c0:25:2f:ff:ff:ff
wifi_sys_linkup(), wdev idx = 0
wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:287 for WDEV_TYPE:1
LinkToOmacIdx = 0, LinkToWdevType = 1
TRTableInsertMcastEntry:band0 group_idx[0]=0
(bssUpdateChannel), ucPrimCh=5, ucCentChSeg0=7, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1
bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 8320
UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0
Enable 20/40 BSSCoex Channel Scan(BssCoex=1)
MtCmdSetMacTxRx:(ret = 0)
MtCmdSetMacTxRx:(ret = 0)
MtCmdChannelSwitch: control_chl = 2,control_ch2=0, central_chl = 2 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 2,control_ch2=0, central_chl = 2, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
AP OBSS SYNC - BBP R4 to 20MHz.l
MtCmdChannelSwitch: control_chl = 3,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 3,control_ch2=0, central_chl = 3, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
AP OBSS SYNC - BBP R4 to 20MHz.l
MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 4,control_ch2=0, central_chl = 4, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
AP OBSS SYNC - BBP R4 to 20MHz.l
MtCmdChannelSwitch: control_chl = 5,control_ch2=0, central_chl = 5 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 5,control_ch2=0, central_chl = 5, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
AP OBSS SYNC - BBP R4 to 20MHz.l
MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 6,control_ch2=0, central_chl = 6, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
AP OBSS SYNC - BBP R4 to 20MHz.l
MtCmdChannelSwitch: control_chl = 7,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 7,control_ch2=0, central_chl = 7, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
AP OBSS SYNC - BBP R4 to 20MHz.l
MtCmdChannelSwitch: control_chl = 8,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 8,control_ch2=0, central_chl = 8, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
AP OBSS SYNC - BBP R4 to 20MHz.l
MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 9,control_ch2=0, central_chl = 9, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
AP OBSS SYNC - BBP R4 to 20MHz.l
MtCmdChannelSwitch: control_chl = 10,control_ch2=0, central_chl = 10 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 10,control_ch2=0, central_chl = 10, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
AP OBSS SYNC - BBP R4 to 20MHz.l
MtCmdChannelSwitch: control_chl = 11,control_ch2=0, central_chl = 11 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 11,control_ch2=0, central_chl = 11, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
AP OBSS SYNC - BBP R4 to 20MHz.l
MtCmdChannelSwitch: control_chl = 12,control_ch2=0, central_chl = 12 DBDCIdx= 0, Band= 0
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 12,control_ch2=0, central_chl = 12, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(1), Channel_Band = 0
AP OBSS SYNC - BBP R4 to 20MHz.l
Channel[Idx=1, Ch=2].bEffectedChannel=0x1!
needFallBack=TRUE due to OS!
Channel[Idx=2, Ch=3].bEffectedChannel=0x0!
Channel[Idx=3, Ch=4].bEffectedChannel=0x2!
needFallBack=TRUE due to OP/OT!
Channel[Idx=4, Ch=5].bEffectedChannel=0x3!
needFallBack=TRUE due to OS!
Channel[Idx=5, Ch=6].bEffectedChannel=0x2!
needFallBack=TRUE due to OP/OT!
Channel[Idx=6, Ch=7].bEffectedChannel=0x0!
Channel[Idx=7, Ch=8].bEffectedChannel=0x1!
needFallBack=TRUE due to OS!
Channel[Idx=8, Ch=9].bEffectedChannel=0x3!
needFallBack=TRUE due to OP/OT!
Channel[Idx=9, Ch=10].bEffectedChannel=0x2!
needFallBack=TRUE due to OP/OT!
Channel[Idx=10, Ch=11].bEffectedChannel=0x2!
needFallBack=TRUE due to OP/OT!
Channel[Idx=11, Ch=12].bEffectedChannel=0x0!
MtCmdChannelSwitch: control_chl = 5,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0
BW = 1,TXStream = 2, RXStream = 2, scan(0)
MtCmdSetTxRxPath: control_chl = 5,control_ch2=0, central_chl = 7, BW = 1,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =0, scan(0), Channel_Band = 0
Caller: SetCommonHT+0xc8/0x1ac
phy_mode=78, ch=5, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
iwpriv ra0 set hw_nat_register=1
iwpriv ra0 mac 83082038=00000f00
MacAddr=0x83082038, MacValue=0xf00, IsRemap=1
iwpriv ra0 mac 8308203c=00000000
MacAddr=0x8308203c, MacValue=0x0, IsRemap=1
iwpriv ra0 mac 83092038=00000f00
MacAddr=0x83092038, MacValue=0xf00, IsRemap=1
iwpriv ra0 mac 8309203c=00000000
MacAddr=0x8309203c, MacValue=0x0, IsRemap=1
brctl addif br-lan ra0
device ra0 entered promiscuous mode
br-lan: port 2(ra0) entered forwarding state
br-lan: port 2(ra0) entered forwarding state
brctl show br-lan
brctl setifvlan br-lan eth0.2 3 1
brctl addif br-lan ra0
device ra0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan ra0 3 1
brctl addif br-lan ra1
can't add ra1 to bridge br-lan: Invalid argument
brctl setifvlan br-lan ra1 4 1
can't set ra1 vlan to bridge br-lan: Invalid argument
brctl addif br-lan apcli0
device apcli0 entered promiscuous mode
brctl setifvlan br-lan apcli0 3 1
brctl addif br-lan rax0
can't add rax0 to bridge br-lan: Invalid argument
brctl setifvlan br-lan rax0 3 1
can't set rax0 vlan to bridge br-lan: Invalid argument
brctl addif br-lan rax1
can't add rax1 to bridge br-lan: Invalid argument
brctl setifvlan br-lan rax1 8 1
can't set rax1 vlan to bridge br-lan: Invalid argument
brctl addif br-lan apclix0
device apclix0 entered promiscuous mode
brctl setifvlan br-lan apclix0 3 1
wifi_vap ra1
wifi_vap dbdc mode
brctl delif br-lan ra1
ifconfig ra1 down
brctl show br-lan
brctl setifvlan br-lan eth0.2 3 1
brctl addif br-lan ra0
device ra0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan ra0 3 1
iptables: No chain/target/match by that name.
brctl addif br-lan ra1
can't add ra1 to bridge br-lan: Invalid argument
brctl setifvlan br-lan ra1 4 1
can't set ra1 vlan to bridge br-lan: Invalid argument
brctl addif br-lan apcli0
device apcli0 is already a member of a bridge; can't enslave it to bridge br-lan.
iptables: No chain/target/match by that name.
brctl setifvlan br-lan apcli0 3 1
iptables: No chain/target/match by that name.
brctl addif br-lan rax0
can't add rax0 to bridge br-lan: Invalid argument
brctl setifvlan br-lan rax0 3 1
can't set rax0 vlan to bridge br-lan: Invalid argument
brctl addif br-lan rax1
can't add rax1 to bridge br-lan: Invalid argument
iptables: No chain/target/match by that name.
brctl setifvlan br-lan rax1 8 1
can't set rax1 vlan to bridge br-lan: Invalid argument
brctl addif br-lan apclix0
device apclix0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan apclix0 3 1
wifi_vdevice apcli0 left promiscuous mode
ap apcli0
wifi_br-lan: port 3(apcli0) entered disabled state
vap dbdc mode
brctl delif br-lan apcli0
iptables: No chain/target/match by that name.
ifconfig apcli0 down
brctl show br-lan
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
brctl setifvlan br-lan eth0.2 3 1
iptables: No chain/target/match by that name.
brctl addif br-lan ra0
device ra0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan ra0 3 1
iptables: No chain/target/match by that name.
brctl addif br-lan ra1
can't add ra1 to bridge br-lan: Invalid argument
iptables: No chain/target/match by that name.
brctl setifvlan br-lan ra1 4 1
can't set ra1 vlan to bridge br-lan: Invalid argument
iptables: No chain/target/match by that name.
brctl addif br-lan apcli0
device apcli0 entered promiscuous mode
brctl setifvlan br-lan apcli0 3 1
brctl addif br-lan rax0
can't add rax0 to bridge br-lan: Invalid argument
brctl setifvlan br-lan rax0 3 1
can't set rax0 vlan to bridge br-lan: Invalid argument
brctl addif br-lan rax1
iptables: No chain/target/match by that name.
can't add rax1 to bridge br-lan: Invalid argument
brctl setifvlan br-lan rax1 8 1
can't set rax1 vlan to bridge br-lan: Invalid argument
brctl addif br-lan apclix0
device apclix0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan apclix0 3 1
wifi_radio wifi1
wifi_shutdown_interface wifi1
ifconfig rax0 down
ifconfig rax1 down
ifconfig apclix0 down
wifi_config_profile wifi1
wifi_config_profile dbdc mode and return
wifi_start_interface wifi1
iptables: No chain/target/match by that name.
wifi_vap rax0
wifi_vap dbdc mode
ifconfig rax0 up
rax0: ===> mbss_virtual_if_open
RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT
RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP
wifi_sys_open(), wdev idx = 3
rcUpdateBandForBFMU PhyCtrl[0].RadioCtrl.IsBfBand = 1
rcUpdateBandForBFMU PhyCtrl[1].RadioCtrl.IsBfBand = 1
TxBfModuleEnCtrl:u1BfNum = 2, u1BfBitmap = 3, u1BfSelBand[0] = 0
ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0
ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0
BuildChannelList() BandIdx = 1, PhyMode = 177, ChListNum = 4:
iptables: phy_oper_init(): operate TxStream = 2, RxStream = 2
No chain/target/#[1;33m [RadarStateCheck] RD_NORMAL_MODE #[m
match by that naMtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 1
me.
BW = 2,TXStream = 2, RXStream = 2, scan(0)
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
MtCmdSetTxRxPath: control_chl = 36,control_ch2=0, central_chl = 42, BW = 2,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =1, scan(0), Channel_Band = 1
Caller: wlan_operate_init+0xac/0x11c
phy_mode=177, ch=36, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
wdev_attr_update(): wdevId3 = c0:25:2f:ff:ff:ff
AP inf up for ra_3(func_idx) OmacIdx=0
AsicRadioOnOffCtrl(): DbdcIdx=1 RadioOn
ApAutoChannelAtBootUp----------------->
ApAutoChannelAtBootUp: AutoChannelBootup[1] = 1
MtCmdSetMacTxRx:(ret = 0)
MtCmdSetMacTxRx:(ret = 0)
MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 1
BW = 2,TXStream = 2, RXStream = 2, scan(0)
MtCmdSetTxRxPath: control_chl = 36,control_ch2=0, central_chl = 42, BW = 2,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =1, scan(0), Channel_Band = 1
ApAutoChannelAtBootUp<-----------------
[PMF]APPMFInit:: apidx=3, MFPC=0, MFPR=0, SHA256=0
Caller: SetCommonHT+0xc8/0x1ac
phy_mode=177, ch=36, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
wifi_sys_linkup(), wdev idx = 3
wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:286 for WDEV_TYPE:1
LinkToOmacIdx = 0, LinkToWdevType = 1
TRTableInsertMcastEntry:band1 group_idx[3]=3
(bssUpdateChannel), ucPrimCh=36, ucCentChSeg0=42, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1
bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8320
UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0
MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 1, BandIdx: 1
MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 1
MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 1
set muru_update_he_cfg()!!!!
SrMbssInit: Spatial Reuse initialize via profile.
PrintSrCmd:
u1CmdSubId = f, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
PrintSrCmd:
u1CmdSubId = 13, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
PrintSrCmd:
u1CmdSubId = 10, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
apidx 3 for WscUUIDInit
Generate UUID for apidx(3)
iwpriv rax0 set SSID=MERCUSYS_0134_5G
iwpriv rax0 set HideSSID=0
iwpriv rax0 set BeaconPeriod=100
iwpriv rax0 set RTSThreshold=2346
Set_RTSThreshold_Proc: set wdev3 rts length threshold=2346(0x92a)
iwpriv rax0 set FragThreshold=2346
Set_FragThreshold_Proc::set wdev3 FragThreshold=2346)
iwpriv rax0 set DtimPeriod=1
iwpriv rax0 set WmmCapable=1
Caller: SetCommonHT+0xc8/0x1ac
phy_mode=177, ch=36, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
iwpriv rax0 set NoForwarding=0
iwpriv rax0 set NoForwardingBTNBSSID=0
iwpriv rax0 set UAPSDCapable=1
config_profile_setting_through_iwpriv rax0
iwprcfg_mode=17
iv rax0 set Wirecfg_mode=17
lessMode=17
iwpriv rax0 set HtBw=1
iwpriv rax0 set VhtBw=1
iwpriv rax0 set ApChannel=0
phy_freq_adjust : no prim_ch value for adjust!
APStop(), oper(1) bssid(3)=c0:25:2f:ff:ff:ff
wifi_sys_linkdown(), wdev idx = 3
ExtEventBeaconLostHandler::FW EVENT (c0:25:2f:ff:ff:ff), Reason 0x10
AP Beacon OFF!!!
(bssUpdateChannel), ucPrimCh=36, ucCentChSeg0=42, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1
bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0
wifi_sys_close(), wdev idx = 3
APStartUp(), oper(1) bssid(3)=c0:25:2f:ff:ff:ff
wifi_sys_open(), wdev idx = 3
rcUpdateBandForBFMU PhyCtrl[0].RadioCtrl.IsBfBand = 1
rcUpdateBandForBFMU PhyCtrl[1].RadioCtrl.IsBfBand = 1
TxBfModuleEnCtrl:u1BfNum = 2, u1BfBitmap = 3, u1BfSelBand[0] = 0
ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0
ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0
phy_oper_init(): operate TxStream = 2, RxStream = 2
#[1;33m [RadarStateCheck] RD_NORMAL_MODE #[m
phy_freq_adjust : no prim_ch value for adjust!
Caller: wlan_operate_init+0xac/0x11c
phy_mode=177, ch=0, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
iptables: ht_cap: ht_cap->HtCapParm,
No chain/target/mdpu_density=5, ampdu_factor=3
match by that nawdev_attr_update(): wdevId3 = c0:25:2f:ff:ff:ff
me.
AP inf up for ra_3(func_idx) OmacIdx=0
AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn
ApAutoChannelAtBootUp----------------->
ApAutoChannelAtBootUp: AutoChannelBootup[1] = 1
MtCmdSetMacTxRx:(ret = 0)
MtCmdSetMacTxRx:(ret = 0)
MtCmdGetChBusyCnt:(ret = 0)
[AutoChSelBuildChannelListFor5G] ChListNum5G = 4
iptables: No chaMtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 36 DBDCIdx= 1, Band= 1
in/target/match BW = 0,TXStream = 2, RXStream = 2, scan(1)
by that name.
iptables: No chain/target/MtCmdSetTxRxPath: control_chl = 36,control_ch2=0, central_chl = 36, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =1, scan(1), Channel_Band = 1
match by that naMtCmdGetChBusyCnt:(ret = 0)
me.
iptables: No chain/target/match by that name.
MtCmdGetChBusyCnt:(ret = 0)
MtCmdChannelSwitch: control_chl = 40,control_ch2=0, central_chl = 40 DBDCIdx= 1, Band= 1
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 40,control_ch2=0, central_chl = 40, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =1, scan(1), Channel_Band = 1
MtCmdGetChBusyCnt:(ret = 0)
Another app is currently holding the xtables lock; waiting for it to exit...
MtCmdGetChBusyCnt:(ret = 0)
MtCmdChannelSwitch: control_chl = 44,control_ch2=0, central_chl = 44 DBDCIdx= 1, Band= 1
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 44,control_ch2=0, central_chl = 44, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =1, scan(1), Channel_Band = 1
MtCmdGetChBusyCnt:(ret = 0)
MtCmdGetChBusyCnt:(ret = 0)
MtCmdChannelSwitch: control_chl = 48,control_ch2=0, central_chl = 48 DBDCIdx= 1, Band= 1
BW = 0,TXStream = 2, RXStream = 2, scan(1)
MtCmdSetTxRxPath: control_chl = 48,control_ch2=0, central_chl = 48, BW = 0,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =1, scan(1), Channel_Band = 1
MtCmdGetChBusyCnt:(ret = 0)
br-lan: port 2(ra0) entered forwarding state
MtCmdGetChBusyCnt:(ret = 0)
====================================================================
Channel 36 : Busy Time = 317, Skip Channel = FALSE, BwCap = TRUE
Channel 40 : Busy Time = 388, Skip Channel = FALSE, BwCap = TRUE
Channel 44 : Busy Time = 100, Skip Channel = FALSE, BwCap = TRUE
Channel 48 : Busy Time = 223, Skip Channel = FALSE, BwCap = TRUE
====================================================================
Rule 3 Channel Busy time value : Select Primary Channel 44
Rule 3 Channel Busy time value : Min Channel Busy = 388
Rule 3 Channel Busy time value : BW = 80
[SelectClearChannelBusyTime] - band1 END
ApAutoChannelAtBootUp : Auto channel selection: Selected channel = 44, IsAband = 1
MtCmdChannelSwitch: control_chl = 44,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 1
BW = 2,TXStream = 2, RXStream = 2, scan(0)
MtCmdSetTxRxPath: control_chl = 44,control_ch2=0, central_chl = 42, BW = 2,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =1, scan(0), Channel_Band = 1
ApAutoChannelAtBootUp<-----------------
[PMF]APPMFInit:: apidx=3, MFPC=0, MFPR=0, SHA256=0
Caller: SetCommonHT+0xc8/0x1ac
phy_mode=177, ch=44, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
wifi_sys_linkup(), wdev idx = 3
wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:286 for WDEV_TYPE:1
LinkToOmacIdx = 0, LinkToWdevType = 1
TRTableInsertMcastEntry:band1 group_idx[3]=3
(bssUpdateChannel), ucPrimCh=44, ucCentChSeg0=42, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1
bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8320
UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0
MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 1, BandIdx: 1
MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 1
MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 1
set muru_update_he_cfg()!!!!
SrMbssInit: Spatial Reuse initialize via profile.
PrintSrCmd:
u1CmdSubId = f, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
PrintSrCmd:
u1CmdSubId = 13, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
PrintSrCmd:
u1CmdSubId = 10, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0
u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0
apidx 3 for WscUUIDInit
Generate UUID for apidx(3)
Main bssid = c0:25:2f:ff:ff:ff
iwpriv rax0 set AutoChannelSel=3
#[42mSet_AutoChannelSel_Proc: Alg = 3 #[m
Set_AutoChannelSel_Proc, channel != 0, no need to perform ACS!
iwpriv rax0 set MuMimo=1
iwpriv rax0 set MuOfdma=0
iwpriv rax0 set twtsupport=0
iwpriv rax0 set twtEnable=0
iwpriv rax0 set PowerDropCtrl=100
SetPowerDropCtrl: ucPowerDrop = 100
killall -q -SIGINT rtinicapd
iwpriv rax0 set AuthMode=WPA2PSK
iwpriv rax0 set EncrypType=AES
iwpriv rax0 set IEEE8021X=0
iwpriv rax0 set RekeyInterval=0
I/F(ra3) GroupKey ReKeyInterval=0 seconds
iptables: No chain/target/match by that name.
iwpriv rax0 set WPAPSK=71378992
iwpriv rax0 set WscConfMode=7
iwpriv rax0 set WscConfStatus=2
iptables: No chain/target/match by that name.
iwpriv rax0 set WscVendorPinCode=71378992
iwpriv rax0 set WscLabelDisabled=0
iwpriv rax0 set WscSetupLock=0
iwpriv rax0 set HideSSID=0
iptables: No chain/target/match by that name.
iwpriv rax0 set ApSSID=MERCUSYS_0134_5G
[PMF]APPMFInit:: apidx=3, MFPC=0, MFPR=0, SHA256=0
wifi_sys_linkdown(), wdev idx = 3
ExtEventBeaconLostHandler::FW EVENT (c0:25:2f:ff:ff:ff), Reason 0x10
AP Beacon OFF!!!
(bssUpdateChannel), ucPrimCh=44, ucCentChSeg0=42, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1
bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0
wifi_sys_close(), wdev idx = 3
wifi_sys_open(), wdev idx = 3
rcUpdateBandForBFMU PhyCtrl[0].RadioCtrl.IsBfBand = 1
rcUpdateBandForBFMU PhyCtrl[1].RadioCtrl.IsBfBand = 1
TxBfModuleEnCtrl:u1BfNum = 2, u1BfBitmap = 3, u1BfSelBand[0] = 0
ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0
ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0
phy_oper_init(): operate TxStream = 2, RxStream = 2
#[1;33m [RadarStateCheck] RD_NORMAL_MODE #[m
MtCmdChannelSwitch: control_chl = 44,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 1
BW = 2,TXStream = 2, RXStream = 2, scan(0)
MtCmdSetTxRxPath: control_chl = 44,control_ch2=0, central_chl = 42, BW = 2,TXStream = 2, RXStream = 2,RXPath = 3, BandIdx =1, scan(0), Channel_Band = 1
Caller: wlan_operate_init+0xac/0x11c
phy_mode=177, ch=44, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
wdev_attr_update(): wdevId3 = c0:25:2f:ff:ff:ff
wifi_sys_linkup(), wdev idx = 3
wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:286 for WDEV_TYPE:1
LinkToOmacIdx = 0, LinkToWdevType = 1
TRTableInsertMcastEntry:band1 group_idx[3]=3
(bssUpdateChannel), ucPrimCh=44, ucCentChSeg0=42, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1
bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8320
UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0
iwpriv rax0 set hw_nat_register=1
iwpriv rax0 mac 83082038=00000f00
MacAddr=0x83082038, MacValue=0xf00, IsRemap=1
iwpriv rax0 mac 8308203c=00000000
MacAddr=0x8308203c, MacValue=0x0, IsRemap=1
iwpriv rax0 mac 83092038=00000f00
MacAddr=0x83092038, MacValue=0xf00, IsRemap=1
iwpriv rax0 mac 8309203c=00000000
MacAddr=0x8309203c, MacValue=0x0, IsRemap=1
brctl addif br-lan rax0
device rax0 entered promiscuous mode
br-lan: port 5(rax0) entered forwarding state
br-lan: port 5(rax0) entered forwarding state
brctl show br-lan
brctl setifvlan br-lan eth0.2 3 1
brctl addif br-lan ra0
device ra0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan ra0 3 1
brctl addif br-lan ra1
can't add ra1 to bridge br-lan: Invalid argument
brctl setifvlan br-lan ra1 4 1
can't set ra1 vlan to bridge br-lan: Invalid argument
brctl addif br-lan apcli0
device apcli0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan apcli0 3 1
brctl addif br-lan rax0
device rax0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan rax0 3 1
brctl addif br-lan rax1
can't add rax1 to bridge br-lan: Invalid argument
brctl setifvlan br-lan rax1 8 1
can't set rax1 vlan to bridge br-lan: Invalid argument
brctl addif br-lan apclix0
device apclix0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan apclix0 3 1
wifi_vap rax1
wifi_vap dbdc mode
brctl delif br-lan rax1
ifconfig rax1 down
iptables: No chain/target/match by that name.
brctl show br-lan
brctl setifvlan br-lan eth0.2 3 1
brctl addif br-lan ra0
device ra0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan ra0 3 1
iptables: No chain/target/match by that name.
brctl addif br-lan ra1
can't add ra1 to bridge br-lan: Invalid argument
brctl setifvlan br-lan ra1 4 1
can't set ra1 vlan to bridge br-lan: Invalid argument
brctl addif br-lan apcli0
iptables: No chain/target/match by that name.
device apcli0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan apcli0 3 1
iptables: No chain/target/match by that name.
brctl addif br-lan rax0
iptables: No chain/target/match by that name.
device rax0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan rax0 3 1
brctl addif br-lan rax1
can't add rax1 to bridge br-lan: Invalid argument
brctl setifvlan br-lan rax1 8 1
can't set rax1 vlan to bridge br-lan: Invalid argument
brctl addif br-lan apclix0
device apclix0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan apclix0 3 1
iptables: No chain/target/match by that name.
wifi_vap apclix0
wifi_vap dbdc mode
brctl delif br-lan apdevice apclix0 left promiscuous mode
clix0
br-lan: port 4(apclix0) entered disabled state
ifconfig apclix0 down
brctl show br-lan
iptables: No chain/target/match by that name.
brctl setifvlan br-lan eth0.2 3 1
brctl addif br-lan ra0
device ra0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan ra0 3 1
brctl addif br-lan ra1
iptables: No chain/target/match by that name.
can't add ra1 to bridge br-lan: Invalid argument
brctl setifvlan br-lan ra1 4 1
can't set ra1 vlan to bridge br-lan: Invalid argument
brctl addif br-lan apcli0
device apcli0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan apcli0 3 1
brctl addif br-lan rax0
device rax0 is already a member of a bridge; can't enslave it to bridge br-lan.
brctl setifvlan br-lan rax0 3 1
iptables: No chain/target/match by that name.
brctl addif br-lan rax1
can't add rax1 to bridge br-lan: Invalid argument
brctl setifvlan br-lan rax1 8 1
can't set rax1 vlan to bridge br-lan: Invalid argument
iptables: No chain/target/match by that name.
brctldevice apclix0 entered promiscuous mode
addif br-lan apclix0
brctl setifvlan br-lan apclix0 3 1
=====config smart connect
iwpriv ra0 set BndStrgEnable=0
#[1;32mBndStrg is already Disable
#[0miwpriv rax0 set BndStrgEnable=0
#[1;32mBndStrg is already Disable
#[0miptables: No chain/target/match by that name.
========= don't cli WIFI-led when booting or not cal
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
br-lan: port 5(rax0) entered forwarding state
[IPTV] WAN_PHY_IF=eth1.1
[IPTV] LAN_PHY_IF=eth0.2
do nothing in nat_hw_enable
wifi_macfilter
iwpriv ra0 set AccessPolicy=0
iwpriv rax0 set AccessPolicy=0
===>>>rftestflag=1!!
#SFE STARTED---
button cycle succeed
dhcp_hook_d not load
Ralink HW NAT Module Enabled
init PpeFoeBase = a0d00000
eth0 ifindex =6
eth1 ifindex =9
PpeDevRegHandler : ineterface ra0 register (0)
PpeDevRegHandler : ineterface rax0 register (1)
PpeDevRegHandler : ra0 dst_port table has beed registered(0)
PpeDevRegHandler : rax0 dst_port table has beed registered(1)
General shell run!
dev = wifi0
dev = wifi1
wifi_led_set 2g = ON, 5g = ON
BusyBox v1.19.4 (2020-12-21 16:36:44 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
MM NM MMMMMMM M M
$MMMMM MMMMM MMMMMMMMMMM MMM MMM
MMMMMMMM MM MMMMM. MMMMM:MMMMMM: MMMM MMMMM
MMMM= MMMMMM MMM MMMM MMMMM MMMM MMMMMM MMMM MMMMM'
MMMM= MMMMM MMMM MM MMMMM MMMM MMMM MMMMNMMMMM
MMMM= MMMM MMMMM MMMMM MMMM MMMM MMMMMMMM
MMMM= MMMM MMMMMM MMMMM MMMM MMMM MMMMMMMMM
MMMM= MMMM MMMMM, NMMMMMMMM MMMM MMMM MMMMMMMMMMM
MMMM= MMMM MMMMMM MMMMMMMM MMMM MMMM MMMM MMMMMM
MMMM= MMMM MM MMMM MMMM MMMM MMMM MMMM MMMM
MMMM$ ,MMMMM MMMMM MMMM MMM MMMM MMMMM MMMM MMMM
MMMMMMM: MMMMMMM M MMMMMMMMMMMM MMMMMMM MMMMMMM
MMMMMM MMMMN M MMMMMMMMM MMMM MMMM
MMMM M MMMMMMM M M
M
---------------------------------------------------------------
For those about to rock... (Attitude Adjustment, unknown)
---------------------------------------------------------------
root@Akronite:/#
|
| OpenWrt Boot log (22.03.4) |
|---|
U-Boot 1.1.3 (Dec 21 2020 - 16:49:33)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer at: 87f58000
Config XHCI 40M PLL
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:Dec 21 2020 Time:16:49:33
============================================
THIS IS uboot
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 880 MHZ ####
estimate memory size =128 Mbytes
Press '4' or 't' to break the booting process
Press 'x' to enter recovery web server
nm_init:791
nm_initFwupPtnStruct:276
nm_lib_readPtnTable:738
[NM_Debug](nm_lib_readPtnTable) 00743: NM_PTN_TABLE_BASE = 0xfe0000
[NM_Debug](nm_lib_readPtnFromNvram) 00569: partition_used_len = 1054, requried len = 8192
[NM_Debug](nm_lib_readPtnTable) 00751: Reading Partition Table from NVRAM ... OK
[NM_Debug](nm_lib_readPtnTable) 00759: Parsing Partition Table ... OK
[NM_Debug](nm_lib_readPtnFromNvram) 00569: partition_used_len = 2, requried len = 2
factory boot check integer ok.
3: System Boot system code via Flash.
## Booting image at bc040000 ...
Image Name: MIPS OpenWrt Linux-5.10.176
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2722011 Bytes = 2.6 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 5.10.176 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r20123-38ccc47687) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sun Apr 9 12:27:46 2023
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Mercusys MR70X v1
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s30480 r8192 d22768 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.000000] Writing ErrCtl register=000411c2
[ 0.000000] Readback ErrCtl register=000411c2
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 119476K/131072K available (7064K kernel code, 631K rwdata, 832K rodata, 1252K init, 243K bss, 11596K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000011] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.007939] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.016990] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.083143] pid_max: default: 32768 minimum: 301
[ 0.087899] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.095101] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.105603] rcu: Hierarchical SRCU implementation.
[ 0.110636] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.118723] smp: Bringing up secondary CPUs ...
[ 0.123972] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.123983] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.123993] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.124066] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.178485] Synchronize counters for CPU 1: done.
[ 0.210394] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.210403] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.210410] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.210456] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.269632] Synchronize counters for CPU 2: done.
[ 0.300235] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.300243] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.300251] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.300299] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.354818] Synchronize counters for CPU 3: done.
[ 0.384683] smp: Brought up 1 node, 4 CPUs
[ 0.392637] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.402453] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.409459] pinctrl core: initialized pinctrl subsystem
[ 0.417080] NET: Registered protocol family 16
[ 0.422697] thermal_sys: Registered thermal governor 'step_wise'
[ 0.423645] cpuidle: using governor teo
[ 0.473310] clocksource: Switched to clocksource GIC
[ 0.480263] NET: Registered protocol family 2
[ 0.485037] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.493580] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.501891] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.509553] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.516532] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.522969] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.529450] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.536661] NET: Registered protocol family 1
[ 0.540955] PCI: CLS 0 bytes, default 32
[ 0.547455] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.557854] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.563644] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.574243] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.583554] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.589385] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.595254] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.601695] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.612126] printk: console [ttyS0] disabled
[ 0.616475] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 0.625468] printk: console [ttyS0] enabled
[ 0.625468] printk: console [ttyS0] enabled
[ 0.633744] printk: bootconsole [early0] disabled
[ 0.633744] printk: bootconsole [early0] disabled
[ 0.646272] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 0.653215] spi-nor spi0.0: w25q128 (16384 Kbytes)
[ 0.658178] 5 fixed-partitions partitions found on MTD device spi0.0
[ 0.664587] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 0.671884] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 0.679962] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 0.687319] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions
[ 0.695720] Creating 5 MTD partitions on "spi0.0":
[ 0.700519] 0x000000000000-0x000000040000 : "u-boot"
[ 0.706501] 0x000000040000-0x000000fa0000 : "firmware"
[ 0.712739] 2 uimage-fw partitions found on MTD device firmware
[ 0.718727] Creating 2 MTD partitions on "firmware":
[ 0.723713] 0x000000000000-0x0000002a0000 : "kernel"
[ 0.729641] 0x0000002a0000-0x000000f60000 : "rootfs"
[ 0.735417] mtd: setting mtd3 (rootfs) as root device
[ 0.740631] 1 squashfs-split partitions found on MTD device rootfs
[ 0.746859] 0x0000006a0000-0x000000f60000 : "rootfs_data"
[ 0.753331] 0x000000fa0000-0x000000fb0000 : "config"
[ 0.759310] 0x000000fb0000-0x000000ff0000 : "tplink"
[ 0.765299] 0x000000ff0000-0x000001000000 : "radio"
[ 0.814659] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 0.825207] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 0.834506] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe100000, irq 21
[ 0.843928] i2c /dev entries driver
[ 0.850099] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 0.856862] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 0.865666] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 0.873863] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 0.882102] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 0.889717] NET: Registered protocol family 10
[ 0.896049] Segment Routing with IPv6
[ 0.899814] NET: Registered protocol family 17
[ 0.904427] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.917744] 8021q: 802.1Q VLAN Support v1.8
[ 0.925389] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 0.955643] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=26)
[ 0.967888] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=27)
[ 0.980037] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=28)
[ 0.993029] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 1.003458] DSA: tree 0 setup
[ 1.006708] rt2880-pinmux pinctrl: pcie is already enabled
[ 1.012241] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 1.018957] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 1.027756] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 1.035925] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 1.044184] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 1.051887] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 1.059514] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[ 1.166859] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 1.172425] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 1.278097] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 1.285048] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 1.289902] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.294773] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 1.304202] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 1.310544] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 1.317412] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.324286] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.329751] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
[ 1.339942] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.345957] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.352199] pci 0000:00:00.0: reg 0x14: initial BAR value 0x00000000 invalid
[ 1.359230] pci 0000:00:00.0: reg 0x14: [mem size 0x00010000]
[ 1.365035] pci 0000:00:00.0: supports D1
[ 1.369027] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.375157] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.381173] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.387448] pci 0000:00:01.0: reg 0x14: initial BAR value 0x00000000 invalid
[ 1.394482] pci 0000:00:01.0: reg 0x14: [mem size 0x00010000]
[ 1.400267] pci 0000:00:01.0: supports D1
[ 1.404273] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.411546] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.419559] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.427786] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
[ 1.433842] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 1.440868] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit pref]
[ 1.447576] pci 0000:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[ 1.454609] pci 0000:01:00.0: reg 0x18: [mem size 0x00004000 64bit pref]
[ 1.461295] pci 0000:01:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[ 1.468322] pci 0000:01:00.0: reg 0x20: [mem size 0x00001000 64bit pref]
[ 1.475129] pci 0000:01:00.0: supports D1 D2
[ 1.479382] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.486043] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.502058] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 1.507307] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 1.513393] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.520154] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff pref]
[ 1.527361] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.534206] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
[ 1.540231] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 1.547275] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000 64bit pref]
[ 1.553974] pci 0000:02:00.0: reg 0x18: initial BAR value 0x00000000 invalid
[ 1.560990] pci 0000:02:00.0: reg 0x18: [mem size 0x00004000 64bit pref]
[ 1.567696] pci 0000:02:00.0: reg 0x20: initial BAR value 0x00000000 invalid
[ 1.574729] pci 0000:02:00.0: reg 0x20: [mem size 0x00001000 64bit pref]
[ 1.581521] pci 0000:02:00.0: supports D1 D2
[ 1.585785] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.592411] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.608767] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 1.614017] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 1.620086] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.626865] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff pref]
[ 1.634078] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.640725] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.647325] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.654273] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 1.660856] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 1.667805] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 1.674581] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
[ 1.681771] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
[ 1.688554] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref]
[ 1.695764] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
[ 1.702528] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
[ 1.709305] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 1.716080] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 1.722853] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
[ 1.730596] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
[ 1.738337] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
[ 1.746079] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.751024] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 1.757797] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 1.764567] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 1.771767] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref]
[ 1.779506] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref]
[ 1.787247] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref]
[ 1.794983] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 1.799927] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 1.806705] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
[ 1.813479] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
[ 1.827241] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.838556] Freeing unused kernel memory: 1252K
[ 1.843084] This architecture does not have kernel memory protection.
[ 1.849546] Run /sbin/init as init process
[ 1.854092] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 2.367436] init: Console is alive
[ 2.371159] init: - watchdog -
[ 3.049059] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.159696] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.173716] init: - preinit -
[ 3.881322] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.958615] random: jshn: uninitialized urandom read (4 bytes read)
[ 3.997383] random: jshn: uninitialized urandom read (4 bytes read)
[ 4.243538] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 4.251832] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 4.253799] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 4.267244] 8021q: adding VLAN 0 to HW filter on device lan1
[ 4.275614] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 8.510588] jffs2: notice: (559) jffs2_build_xattr_subsystem: complete building xattr subsystem, 6 of xdatum (0 unchecked, 1 orphan) and 7 of xref (1 dead, 0 orphan) found.
[ 8.528144] mount_root: switching to jffs2 overlay
[ 8.541257] overlayfs: upper fs does not support tmpfile.
[ 8.556301] urandom-seed: Seeding with /etc/urandom.seed
[ 8.724334] procd: - early -
[ 8.727453] procd: - watchdog -
[ 9.363435] procd: - watchdog -
[ 9.461286] procd: - ubus -
[ 9.584933] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.624401] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.631223] random: ubusd: uninitialized urandom read (4 bytes read)
[ 9.647595] procd: - init -
Please press Enter to activate this console.
[ 10.223430] random: crng init done
[ 10.226860] random: 26 urandom warning(s) missed due to ratelimiting
[ 10.397229] kmodloader: loading kernel modules from /etc/modules.d/*
[ 10.517394] urngd: v1.0.2 started.
[ 10.685720] Loading modules backported from Linux version v5.15.92-0-ge515b9902f5f
[ 10.693372] Backport generated by backports.git v5.15.92-1-0-gdfe0f60c
[ 10.879170] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22
[ 10.884623] pci 0000:00:00.0: enabling device (0004 -> 0007)
[ 10.890265] mt7915e_hif 0000:01:00.0: enabling device (0000 -> 0002)
[ 10.897075] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23
[ 10.902556] pci 0000:00:01.0: enabling device (0004 -> 0007)
[ 10.908241] mt7915e 0000:02:00.0: enabling device (0000 -> 0002)
[ 11.162942] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20211222184017a
[ 11.162942]
[ 11.467772] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20211222184052
[ 11.504987] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20211222184111
[ 16.944302] PPP generic driver version 2.4.2
[ 16.950369] NET: Registered protocol family 24
[ 16.963209] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 24.599596] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 24.616793] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 24.625054] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 24.628673] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 24.640715] 8021q: adding VLAN 0 to HW filter on device lan1
[ 24.649299] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 24.656946] br-lan: port 1(lan1) entered blocking state
[ 24.662223] br-lan: port 1(lan1) entered disabled state
[ 24.669355] device lan1 entered promiscuous mode
[ 24.674374] device eth0 entered promiscuous mode
[ 24.711195] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 24.718491] 8021q: adding VLAN 0 to HW filter on device lan2
[ 24.728419] br-lan: port 2(lan2) entered blocking state
[ 24.733770] br-lan: port 2(lan2) entered disabled state
[ 24.740118] device lan2 entered promiscuous mode
[ 24.761235] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 24.768658] 8021q: adding VLAN 0 to HW filter on device lan3
[ 24.779184] br-lan: port 3(lan3) entered blocking state
[ 24.784556] br-lan: port 3(lan3) entered disabled state
[ 24.792260] device lan3 entered promiscuous mode
[ 24.865571] mtk_soc_eth 1e100000.ethernet wan: PHY [mdio-bus:00] driver [Generic PHY] (irq=POLL)
[ 24.874493] mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii-rxid link mode
BusyBox v1.35.0 (2023-04-09 12:27:46 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 22.03.4, r20123-38ccc47687
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#
|
See also
- Mercusys AC10 • AC1200 • 4PDA
- Mercusys AC12 • AC1200 • 4PDA
- Mercusys AC12G • AC1200 • 4PDA
- Mercusys Halo S12 • AC1200 •
- Mercusys MR50G • AC1900 • 4PDA
- Mercusys MR70X • AX1800 • DW • 4PDA
Categories:
- Mercusys
- Embedded system/wireless router
- Embedded System MediaTek
- Embedded System MT7621AT
- MediaTek
- Embedded System MIPS 1004Kc
- Embedded System
- OpenWrt Supported
- Embedded System MT7915D
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n/ax
- Embedded System IEEE 802.11a/n/ac/ax
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- English Documentation
