Linksys WAP55AG v2

multiple revisions of this device, use caution

abg (AG108)
Dual-Band Wireless Access Point
Support	Support page
Wikipedia	Linksys routers
3rd Party Firmware
dd-wrt	Incompatible
OpenWrt	Incompatible
Tomato any flavor	Incompatible
Platform
Brand • Model • Rev	Linksys WAP55AG v2.0
FCC ID	Q87-WAP55AGV2
IC ID	3839A-WAP55AGV2
Type	access point
CPU1	Atheros AR5312A
CPU1 Type	MIPS R4000
CPU1 Speed	220 MHz
Flash1 Chip	Macronix MX29LV160BBTC-90G
Flash1 Size	2 MiB2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br />
RAM1 Size	8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br />
RAM1 Chip	ISSI IS42S32200B-6T
ETH chip1	Atheros AR5312A
ETH chip2	IC+ IP101
Ethernet Port Count	1-100MbE-LAN
Wired Standard	IEEE 802.3i/3u
802dot11 OUI: 00:12:17 (16 E, 32 W) Ethernet OUI: 00:12:17 (16 E, 32 W)
Stock FW OS	VxWorks
Expansion IF types	none specified
Power	5 VDC, 2.5 A
Connector type	barrel 5.5 mm (OD) 2.0 mm (ID)
Serial Port (UART)	yes, internal, 9-pin header, Gemtek Type1 pinout, (9600 8N1), JP1
Additional chips 2.4GHz Power Amplifier IC;Microsemi;LX5510;MSC, 5510, 531BU;1;InGaP/GaAs HBT;16-pin MLPQ;3 mm x 3 mm; 4.5 to 6GHz Power Amplifier IC;Microsemi;LX5506;MSC, 5506, 530CL;1;InGaP/GaAs HBT;16-pin MLPQ;
Other
Default SSID: linksys-a (3 addl. devices) , linksys-g (5 addl. devices) Default IP address: 192.168.1.246 the IP 192.168.1.246 is used by 1 additional devices of which 1 are Linksys devices Default login user: blank Default login password: admin blank:admin credentials used by 278 additional devices of which 135 are Linksys devices
Manuf/OEM/ODM	Gemtek WRTA-119AG
Retail
FCC approval date	30 December 2004
Country of manuf	Taiwan
Radio 1
Chip1	Atheros AR5312A
Chip2	Atheros AR5112A
Wireless interface OUI	00:12:17
Antenna Connector Type	U.FL
Wireless Standard	IEEE 802.11a
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
Radio 2
Chip1	Atheros AR5312A
Chip2	Atheros AR2112A
Wireless interface OUI	00:12:17
Antenna Connector Type	U.FL
Wireless Standard	IEEE 802.11b/g
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
CPU1 brand Radio1 chip1 brand Radio2 chip1 brand Linksys WAP55AG v1 Broadcom Atheros Broadcom Linksys WAP55AG v2 Atheros Atheros Atheros

For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
For a list of all currently documented IC+ chipsets with specifications, see IC+.

For a list of all currently documented Linksys device with specifications, see Linksys.

• 54 Mbps - 5GHz 802.11a

• 54 Mbps - 2.4GHz 802.11g = AG108 class

Overview

• OEM: Gemtek WRTA-119AG (WRTA-119AG_V01)

Default credentials are per the FCC manual.

The default SSIDs for this device are linksys-a and linksys-g.

Appears to support U-NII-2 channels but may not implement Dynamic Frequency Selection (DFS) due to its age.

Links of Interest

• On the DD-WRT forums (pictures)

JTAG-Serial Info

Serial

Credentials

The (default) credentials are the same as the router's default credentials.

Username: <blank>
Password: admin

Info derived from

boot log

ar531x rev 0x00005742 firmware startup... SDRAM TEST SKIPPED Please check the ethernet cable on port 0 Atheros AR5001AP default version 4.0.0.48 Bootloader version 1.01 0 auto-booting... Attaching to TFFS... done. Loading /fl/APIMG1...1073872 Starting at 0x804846e0... /fl/ - Volume is OK Reading Configuration File "/fl/apcfg". Configuration file checksum: 4da56 is good Please check the ethernet cable on port 0! Attaching interface lo0...done vp0 macaddr = 00:12:17:77:41:30 vp65536 macaddr = 00:12:17:77:41:31 ae0 macaddr = 00:12:17:77:41:32 start easy conf wireless access point starting... wlan1 Ready wireless access point starting... Auto Channel Scan selected 5280 MHz, channel 56 wlan0 Ready Ready

AP shell help

WAP55AG wlan0 -> ? List of Access Point CLI commands: add remoteWbr -- Add a remote Wireless Bridge config wlan -- config wlanX connect bss -- connect to bssX del acl -- Delete Access Control List del key -- Delete Encryption key del remoteWbr -- Delete a remote Wireless Bridge find bss -- Find BSS find channel -- Find Available Channel find all -- Find All BSS ftp -- Software update via FTP get acl -- Display Access Control List get aging -- Display Aging Interval get antenna -- Display Antenna Diversity get association -- Display Association Table get authentication -- Display Authentication Type get autochannelselect -- Display Auto Channel Select get beaconinterval -- Display Beacon Interval get burstSeqThreshold -- Display Max Number of frames in a Burst get burstTime -- Display Burst Time get channel -- Display Radio Channel get cipher -- Display Encryption cipher get config -- Display Current AP Configuration get countrycode -- Display Country Code get domainsuffix -- Display Domain Name Server suffix get dtim -- Display Data Beacon Rate (DTIM) get encryption -- Display Encryption Mode get fragmentthreshold -- Display Fragment Threshold get frequency -- Display Radio Frequency (MHz) get gateway -- Display Gateway IP Address get groupkeyupdate -- Display Group Key Update Interval (in Seconds) get hardware -- Display Hardware Revisions get hostipaddr -- Display Host IP Address get ipaddr -- Display IP Address get ipmask -- Display IP Subnet Mask get jsw -- Display Jumpstart Mode get key -- Display Encryption Key get keyentrymethod -- Display Encyrption Key Entry Method get keysource -- Display Source Of Encryption Keys get login -- Display Login User Name get minimumrate -- Display Minimum Rate get nameaddr -- Display IP address of name server get operationMode -- Display Operation Mode get pktLogEnable -- Display Packet Logging Mode get power -- Display Transmit Power Setting get radiusname -- Display RADIUS server name or IP address get radiusport -- Display RADIUS port number get rate -- Display Data Rate get reg -- Display the register contents at the given offset get remoteAp -- Display Remote Ap's Mac Address get remoteWbr -- Display configured Remote Wireless bridges get rtsthreshold -- Display RTS/CTS Threshold get sntpserver -- Display SNTP/NTP Server IP Address get ssid -- Display Service Set ID get ssidsuppress -- Display SSID Suppress Mode get station -- Display Station Status get SuperG -- Display SuperG Feature Status get systemname -- Display Access Point System Name get tzone -- Display Time Zone Setting get upsd -- Display UPSD Mode get uptime -- Display UpTime get vlan -- Display VLAN Mode get wirelessmode -- Display Wireless LAN Mode get wmm -- Display WMM Mode get wmmParamBss -- Display WMM parameters used by STA in this BSS get wmmParam -- Display WMM parameters used by this AP get wlanstate -- Display wlan state help -- Display CLI Command List ping -- Ping pktLog -- Packet Log reboot -- Reboot Access Point run -- Run command file quit -- Logoff set acl -- Set Access Control List set aging -- Set Aging Interval set antenna -- Set Antenna set authentication -- Set Authentication Type set autochannelselect -- Set Auto Channel Selection set beaconinterval -- Modify Beacon Interval set burstSeqThreshold -- Set Max Number of frames in a Burst set burstTime -- Set Burst Time set channel -- Set Radio Channel set cipher -- Set Cipher set countrycode -- Set Country Code set domainsuffix -- Set Domain Name Server Suffix set dtim -- Set Data Beacon Rate (DTIM) set encryption -- Set Encryption Mode set factorydefault -- Restore to Default Factory Settings set fragmentthreshold -- Set Fragment Threshold set frequency -- Set Radio Frequency (MHz) set gateway -- Set Gateway IP Address set groupkeyupdate -- Set Group Key Update Interval (in Seconds) set hostipaddr -- Set Host IP address set ipaddr -- Set IP Address set ipmask -- Set IP Subnet Mask set jsw -- Set Jumpstart Mode set key -- Set Encryption Key set keyentrymethod -- Select Encryption Key Entry Method set keysource -- Select Source Of Encryption Keys set login -- Modify Login User Name set minimumrate -- Set Minimum Rate set nameaddress -- Set Name Server IP address set operationMode -- Set operation Mode set password -- Modify Password set passphrase -- Modify Passphrase set pktLogEnable -- Enable Packet Logging set power -- Set Transmit Power set radiusname -- Set RADIUS name or IP address set radiusport -- Set RADIUS port number set radiussecret -- Set RADIUS shared secret set rate -- Set Data Rate set reg -- Set Register Value set remoteAP -- Set Remote AP's Mac Address set rtsthreshold -- Set RTS/CTS Threshold set sntpserver -- Set SNTP/NTP Server IP Address set ssid -- Set Service Set ID set ssidsuppress -- Set SSID Suppress Mode set SuperG -- Super G Features set systemname -- Set Access Point System Name set tzone -- Set Time Zone Setting set upsd -- Set UPSD Mode set vlan -- Set VLAN Mode set wlanstate -- Set wlan state set wirelessmode -- Set Wireless LAN Mode set wmm -- Set WMM Mode set wmmParamBss -- Set WMM parameters used by STAs in this BSS set wmmParam -- Set WMM parameters used by this AP timeofday -- Display Current Time of Day version -- Software version nvram -- nvram utility

AP shell version + get hardware
WAP55AG wlan0 -> version AP software 4.0.0.80 mars@MARSNB:E:/AP_4.0.0.80_THGSrc_Src/ap/os/vxworks/target/proj/ap-ar5312-production Jan 26 2005, 16:54:11 WAP55AG wlan0 -> get hardware wlan0 revisions: mac 5.7 phy 4.2 analog 3.6 PCI Vendor ID: 0x168c, Device ID: 0x13 Sub Vendor ID: 0x168c, Sub Device ID: 0x13 chip is AR5312

nvram show

WAP55AG wlan0 -> nvram show regulatory_domain=FCC country_domain=US wan_proto=static sys_name=WAP55AG wan_domain= lan_ipaddr=192.168.1.246 lan_netmask=255.255.255.0 dhcps_mode=enabled wan_dns= login_name= login_password=admin lan_gateway=192.168.1.1 wl0_ssid=linksys-a wl0_channel=0 wl0_stat_mode=enabled wl0_wirelessmode=11a wl0_ssid_bcast=enabled wl0_security_mode=disabled wl0_encrypt_idx=40 wl0_key_idx=1 wl0_key1= wl0_key2= wl0_key3= wl0_key4= wl0_cipher_type=tkip wl0_wpa_passphrase= wl0_wpa_group_key_interval=1500 wl0_auth_type=open wl0_transmission_rate=auto wl0_transmission_power=full wl0_frame_burst=enabled wl0_beacon_interval=100 wl0_dtim_interval=1 wl0_frag_threshold=2346 wl0_rts_threshold=2346 wl1_ssid=linksys-g wl1_channel=6 wl1_stat_mode=enabled wl1_wirelessmode=11g wl1_wirelessmode_tmp=11g wl1_ssid_bcast=enabled wl1_security_mode=disabled wl1_encrypt_idx=40 wl1_key_idx=1 wl1_key1= wl1_key2= wl1_key3= wl1_key4= wl1_cipher_type=tkip wl1_wpa_passphrase= wl1_wpa_group_key_interval=1500 wl1_auth_type=open wl1_basic_rate=default wl1_transmission_rate=auto wl1_transmission_power=full wl1_cts_protection_mode=auto wl1_frame_burst=enabled wl1_beacon_interval=100 wl1_dtim_interval=1 wl1_frag_threshold=2346 wl1_rts_threshold=2347 radius_server_ipaddr=0.0.0.0 radius_server_ipaddr_1=0 radius_server_ipaddr_2=0 radius_server_ipaddr_3=0 radius_server_ipaddr_4=0 radius_server_port=1812 radius_shared_key= radius_shared_key_interval=3600 filter_mode=disabled filter_type=allow filter_mac_1=00:00:00:00:00:00 filter_mac_2=00:00:00:00:00:00 filter_mac_3=00:00:00:00:00:00 filter_mac_4=00:00:00:00:00:00 filter_mac_5=00:00:00:00:00:00 filter_mac_6=00:00:00:00:00:00 filter_mac_7=00:00:00:00:00:00 filter_mac_8=00:00:00:00:00:00 filter_mac_9=00:00:00:00:00:00 filter_mac_10=00:00:00:00:00:00 filter_mac_11=00:00:00:00:00:00 filter_mac_12=00:00:00:00:00:00 filter_mac_13=00:00:00:00:00:00 filter_mac_14=00:00:00:00:00:00 filter_mac_15=00:00:00:00:00:00 filter_mac_16=00:00:00:00:00:00 filter_mac_17=00:00:00:00:00:00 filter_mac_18=00:00:00:00:00:00 filter_mac_19=00:00:00:00:00:00 filter_mac_20=00:00:00:00:00:00 filter_mac_21=00:00:00:00:00:00 filter_mac_22=00:00:00:00:00:00 filter_mac_23=00:00:00:00:00:00 filter_mac_24=00:00:00:00:00:00 filter_mac_25=00:00:00:00:00:00 filter_mac_26=00:00:00:00:00:00 filter_mac_27=00:00:00:00:00:00 filter_mac_28=00:00:00:00:00:00 filter_mac_29=00:00:00:00:00:00 filter_mac_30=00:00:00:00:00:00 filter_mac_31=00:00:00:00:00:00 filter_mac_32=00:00:00:00:00:00 filter_mac_33=00:00:00:00:00:00 filter_mac_34=00:00:00:00:00:00 filter_mac_35=00:00:00:00:00:00 filter_mac_36=00:00:00:00:00:00 filter_mac_37=00:00:00:00:00:00 filter_mac_38=00:00:00:00:00:00 filter_mac_39=00:00:00:00:00:00 filter_mac_40=00:00:00:00:00:00 log_mode=disabled log_ipaddr=0.0.0.0 chk_fw_hdr=enabled fw_extension=fim modle_id=LinksysWAP55AGv2 basic_realm=Linksys WAP55AG restore_defaults=0 firmware_version=1.1 my_firmware_version=1.0.22, Jan 26, 2005 customer_firmware_version=1.1, Jan 26, 2005 wl0_macaddr=00:12:17:77:41:30 wl1_macaddr=00:12:17:77:41:31 lan_macaddr=00:12:17:77:41:32

ls
WAP55AG wlan0 -> ls nvram 2881 apcfg 3981 config.bin 3863 apcfg.bak 3981 defaults 85 apimg1.hdr 52 defaults.bak 85 apimg1 968660 452608 bytes free