Due to spambots account creation is turned off, if you'd like an accout please email me at techinfodepot1@gmail.com
You do not need an accout to report a problem with the wiki.

-

Inteno DG150B

From TechInfoDepot
Jump to navigationJump to search
bgn (N300)
Gigabit Residential Gateway
Inteno DG150B.png
Homepage
WikiDevi.wi-cat.ru
3rd Party Firmware
dd-wrt
Status Unknown
OpenWrt
Status Unknown
Tomato any flavor
Status Unknown
Platform
BrandModelRev
Inteno DG150B v1
FCC ID
none specified
Type
wireless router, dsl modem, analog phone gateway, CPE
CPU1 checkY
Broadcom BCM6361V
CPU1 Type
MIPS BMIPS4350
CPU1 Speed
400 MHz ( 2 cores )
Flash1 Chip
Spansion S34ML01G100TFI00
Flash1 Size
128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Size
128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Chip
Micron Model?
ETH chip1
Broadcom BCM6361V
Switch
Broadcom BCM6361V
Ethernet Port Count
1-1GbE-WAN
4-100MbE-LAN
Wired Standard
IEEE 802.3i/3u/3ab

802dot11 OUI: 00:22:07 (1 E, 1 W)
Ethernet OUI: 00:22:07 (1 E, 1 W)

Stock bootloader
CFE 1.0.38-114.185 BCM6361
Stock FW OS
Linux 2.6.30
Expansion IF types
none specified
Power
12 VDC, 1 A
Connector type
barrel
Serial Port (UART)
yes, 4-pin header, 3.3V TTL, (115200 8N1), J304
Flags:
ADSL2+, VoIP

Additional chips
Single-Chip ProSLIC (FXS);Silicon Labs;Si32176;;1;

Other

Default IP address: 10.0.0.1
the IP 10.0.0.1 is used by 21 additional devices
of which 0 are Inteno devices
Default login user: user
Default login password: user
user:user credentials used by 9 additional devices
of which 0 are Inteno devices

Retail
Availability End of Life
Country of manuf China
Radio 1
Chip1
Broadcom BCM6361V
Wireless interface OUI
00:22:07
Antenna Connector Type
none specified
MIMO status
2x2:2
Wireless Standard
IEEE 802.11b/g/n
802.11n
up to 300 Mbps
802.11g
up to 54 Mbps
802.11b
up to 11 Mbps
WiFi Operating Frequency
2.4 GHz

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.

300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class

Overview

  • The CPU on the board is part Broadcom BCM6361VKFEBG

JTAG-Serial Info

Serial

Boot log

bootlog • >>
HELO
CPUI
L1CI
HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
300H
PHYE
DINT
LASY
USYN
MSYN
LMBE
RACE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
FPS0
BT58
0001
BT59
0492
NAN3
RFS2
NAN5


CFE version 1.0.38-114.185 for BCM96362 (32bit,SP,BE)
Build Date: Fri Apr 22 11:09:42 CST 2016 (chris_chiu@cs1)
Copyright (C) 2000-2011 Broadcom Corporation.

NAND flash device: name Spansion S34ML01G1, id 0x01f1 block 128KB size 131072KB
Chip ID: BCM6362B0, MIPS: 400MHz, DDR: 333MHz, Bus: 166MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 134217728 bytes (128MB)
Boot Address: 0xb8000000

Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-13)                   : 96362ADVNgr
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 00:22:07:32:a1:9c
PSI Size (1-64) KBytes            : 24
Enable Backup PSI [0|1]           : 0
System Log Size (0-256) KBytes    : 0
Auxillary File System Size Percent: 0
Main Thread Number [0|1]          : 0
Voice Board Configuration (0-13)  : SI32176

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1�1�0
Booting from latest image (0xbbd80000) ...
Decompression OK!
Entry at 0x8032af00
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x8032af00
Linux version 2.6.30 (chris_chiu@cs1) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Fri Apr 22 11:12:54 CST 2016

BCM Flash API. Flash device is not found.

96362ADVNgr prom init

CPU revision is: 0002a070 (Broadcom4350)

DSL SDRAM reserved: 0x100000

Determined physical RAM map:

 memory: 07f00000 @ 00000000 (usable)

Zone PFN ranges:

  DMA      0x00000000 -> 0x00001000

  Normal   0x00001000 -> 0x00007f00

Movable zone start PFN for each node

early_node_map[1] active PFN ranges

    0: 0x00000000 -> 0x00007f00

On node 0 totalpages: 32512

free_area_init_node: node 0, pgdat 803fcef0, node_mem_map 81000000

  DMA zone: 32 pages used for memmap

  DMA zone: 0 pages reserved

  DMA zone: 4064 pages, LIFO batch:0

  Normal zone: 222 pages used for memmap

  Normal zone: 28194 pages, LIFO batch:7

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32258

Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200

wait instruction: enabled

Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.

Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes

NR_IRQS:128

PID hash table entries: 512 (order: 9, 2048 bytes)

console [ttyS0] enabled

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Allocating memory for DSP module core and initialization code

Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0

Memory: 124204k/130048k available (3212k kernel code, 5656k reserved, 825k data, 152k init, 0k highmem)

Calibrating delay loop... 399.36 BogoMIPS (lpj=199680)

Mount-cache hash table entries: 512

--Kernel Config--

  SMP=1

  PREEMPT=1

  DEBUG_SPINLOCK=0

  DEBUG_MUTEXES=0

Broadcom Logger v0.1 Apr 22 2016 11:10:16

CPU revision is: 0002a070 (Broadcom4350)

Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.

Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes

Calibrating delay loop... 402.43 BogoMIPS (lpj=201216)

Brought up 2 CPUs

net_namespace: 1140 bytes

NET: Registered protocol family 16

Total Flash size: 0K with -1 sectors

registering PCI controller with io_map_base unset

registering PCI controller with io_map_base unset

bio: create slab <bio-0> at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10005fff]

pci 0000:00:00.0: supports D1 D2

pci 0000:00:00.0: PME# supported from D0 D3hot D3cold

pci 0000:00:00.0: PME# disabled

pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]

pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]

pci 0000:01:00.0: PME# supported from D0 D3hot

pci 0000:01:00.0: PME# disabled

pci 0000:01:00.0: PCI bridge, secondary bus 0000:02

pci 0000:01:00.0:   IO window: disabled

pci 0000:01:00.0:   MEM window: disabled

pci 0000:01:00.0:   PREFETCH window: disabled

PCI: Setting latency timer of device 0000:01:00.0 to 64

skbFreeTask created successfully

�[0;34mBLOG v3.0 Initialized�[0m

BLOG Rule v1.0 Initialized

Broadcom IQoS v0.1 Apr 22 2016 11:12:27 initialized

Broadcom GBPM v0.1 Apr 22 2016 11:12:27 initialized

NET: Registered protocol family 8

NET: Registered protocol family 20

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 4096 (order: 3, 32768 bytes)

TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

TCP reno registered

NET: Registered protocol family 1

JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.

fuse init (API version 7.11)

msgmni has been set to 242

io scheduler noop registered (default)

PCI: Setting latency timer of device 0000:01:00.0 to 64

Driver 'sd' needs updating - please use bus_type methods

PPP generic driver version 2.4.2

PPP Deflate Compression module registered

PPP BSD Compression module registered

NET: Registered protocol family 24

bcm963xx_mtd driver v2.0

Failed to read image tag from flash

Broadcom DSL NAND controller (BrcmNand Controller)

-->brcmnand_scan: CS=0, numchips=1, csi=0

mtd->oobsize=0, mtd->eccOobSize=0

NAND_CS_NAND_XOR=00000000

Disabling XOR on CS#0

brcmnand_scan: Calling brcmnand_probe for CS=0

B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0

brcmnand_read_id: CS0: dev_id=01f1001d

After: NandSelect=40000001, nandConfig=15142200

Block size=00020000, erase shift=17

NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11

busWidth=1, pageSize=2 GiBB, page_shift=11, page_mask=000007ff

timing1 not adjusted: 5363444f

timing2 not adjusted: 00000fc6

BrcmNAND mfg 1 f1 SPANSION_S30ML01GP_08 128MB on CS0


Found NAND on CS0: ACC=f3000000, cfg=15142200, flashId=01f1001d, tim1=5363444f, tim2=00000fc6

BrcmNAND version = 0x0202 128MB @00000000

B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0

brcmnand_read_id: CS0: dev_id=01f1001d

After: NandSelect=40000001, nandConfig=15142200

Found NAND flash on Chip Select 0, chipSize=128MB, usable size=128MB, base=0

brcmnand_scan: Done brcmnand_probe

brcmnand_scan: B4 nand_select = 40000001

brcmnand_scan: After nand_select = 40000001

brcmnand_scan 10

200 CS=0, chip->ctrl->CS[0]=0

200 chip->ecclevel=15, acc=f3000000

page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17

brcmnand_scan 220

Brcm NAND controller version = 2.2 NAND flash size 128MB @18000000

brcmnand_scan 230

brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000

brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0

ECC layout=brcmnand_oob_bch4_4k

brcmnand_scan:  mtd->oobsize=64

brcmnand_scan: oobavail=50, eccsize=512, writesize=2 GiB

brcmnand_scan, eccsize=512, writesize=2 GiB, eccsteps=4, ecclevel=15, eccbytes=3

300 CS=0, chip->ctrl->CS[0]=0

500 chip=87a40190, CS=0, chip->ctrl->CS[0]=0

-->brcmnand_default_bbt

brcmnand_default_bbt: bbt_td = bbt_main_descr

Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0

Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0

brcmnandCET: Status -> Deferred

brcmnand_scan 99

Creating 4 MTD partitions on "brcmnand.0":

0x000003d80000-0x000007ae0000 : "rootfs"

0x000000020000-0x000003d80000 : "rootfs_update"

0x000007b00000-0x000007f00000 : "data"

0x000000000000-0x000000020000 : "nvram"

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)

PCI: Setting latency timer of device 0000:00:0a.0 to 64

ehci_hcd 0000:00:0a.0: EHCI Host Controller

ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1

ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM

ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500

ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

PCI: Enabling device 0000:00:09.0 (0000 -> 0002)

PCI: Setting latency timer of device 0000:00:09.0 to 64

ohci_hcd 0000:00:09.0: OHCI Host Controller

ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2

ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600

usb usb2: configuration #1 chosen from 1 choice

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

usbcore: registered new interface driver usblp

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

brcmboard: brcm_board_init entry

kerSysScreenPciDevices: 0x14e4:0x435f:(slot 0) detected

kerSysScreenPciDevices: 0x14e4:0x6300:(slot 9) detected

kerSysScreenPciDevices: 0x14e4:0x6300:(slot 10) detected

kerSysScreenPciDevices: 0x14e4:0x6362:(slot 0) detected

SES: LED GPIO 0xc00c is enabled

PCIe: No device found - Powering down

Serial: BCM63XX driver $Revision: 3.00 $

�[0;33mMagic SysRq enabled (type ^ h for list of supported commands)�[0m

ttyS0 at MMIO 0xb0000100 (irq = 11) is a BCM63XX

ttyS1 at MMIO 0xb0000120 (irq = 12) is a BCM63XX

Total # RxBds=2740

bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized


bcmPktDma_init: Broadcom Packet DMA Library initialized

bcmxtmrt: Broadcom BCM6362B0 ATM/PTM Network Device v0.3 Apr 22 2016 11:12:09

IPSEC SPU: SUCCEEDED

GACT probability NOT on

Mirror/redirect action on

u32 classifier

    input device check on

    Actions configured

TCP cubic registered

Initializing XFRM netlink socket

NET: Registered protocol family 10

IPv6 over IPv4 tunneling driver

NET: Registered protocol family 17

NET: Registered protocol family 15

Initializing MCPD Module

Ebtables v2.0 registered

ebt_time registered

ebt_ftos registered

ebt_wmm_mark registered

802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

VFS: Mounted root (jffs2 filesystem) readonly on device 31:0.

Freeing unused kernel memory: 152k freed


init started: BusyBox v1.17.2 (2016-04-22 11:15:29 CST)

starting pid 221, tty '': '/etc/init.d/rcS'

starting pid 225, tty '': '-/bin/sh'


BusyBox v1.17.2 (2016-04-22 11:15:29 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

chipinfo: module license 'proprietary' taints kernel.

Disabling lock debugging due to kernel taint

brcmchipinfo: brcm_chipinfo_init entry

Broadcom Ingress QoS Module  Char Driver v0.1 Apr 22 2016 11:11:50 Registered<243>�[0m


Broadcom Ingress QoS ver 0.1 initialized

BPM: tot_mem_size=134217728B (128MB), buf_mem_size=20132655B (19MB), num of buffers=9460, buf size=2128

Broadcom BPM Module Char Driver v0.1 Apr 22 2016 11:10:46 Registered<244>�[0m

�[0;34m[NTC bpm] bpm_set_status: BPM status : enabled

�[0m

NBUFF v1.0 Initialized

�[0;36;44mInitialized fcache state�[0m

�[0;36;44mBroadcom Packet Flow Cache  Char Driver v2.2 Apr 22 2016 11:11:50 Registered<242>�[0m

Created Proc FS /procfs/fcache

�[0;36;44mBroadcom Packet Flow Cache registered with netdev chain�[0m

�[0;36;44mBroadcom Packet Flow Cache learning via BLOG enabled.�[0m

�[0;36;44mConstructed Broadcom Packet Flow Cache v2.2 Apr 22 2016 11:11:50�[0m

chipId 0x636220B0

Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Apr 22 2016 11:11:45 Registered <241>

Enabling SMISBUS PHYS_FAP_BASE[0] is 0x14001000

FAP Soft Reset Done

4ke Reset Done

FAP Debug values at 0xa5d9c590 0xa5d9c590

Allocated FAP0 GSO Buffers (0xA5DAD618) : 1048576 bytes @ 0xA5E00000

Allocated FAP0 TM SDRAM Queue Storage (a5dad61c) : 341376 bytes @ a5f00000

�[0;34m[NTC fapProto] fapReset  : Reset FAP Protocol layer�[0m

[FAP0] DSPRAM : stack <0x80004000><1536>, global <0x80004600><3864>, free <2792>, total<8192>

[FAP0] PSM : addr<0xE0010000>, used <24216>, free <8552>, total <32768>

[FAP0] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004600

[FAP0] GSO Buffer set to 0xA5E00000

[FAP0] FAP BPM Initialized.

fapDrv_construct: FAP0: pManagedMemory=b1010650. wastage 8 bytes

bcmPktDma_bind: FAP Driver binding successfull

[FAP0] FAP TM: ON

bcmxtmcfg: bcmxtmcfg_init entry

adsl: adsl_init entry

Broadcom BCM6362B0 Ethernet Network Device v0.1 Apr 22 2016 11:12:03

fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b1010650 bytes remaining 7000

ETH Init: Ch:0 - 200 tx BDs at 0xb1010650

fapDrv_psmAlloc: wastage 8 bytes

fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b1011910 bytes remaining 2184

ETH Init: Ch:0 - 600 rx BDs at 0xb1011910

ETH Init: Ch:1 - 1892 rx BDs at 0xa7a18000

dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered

eth0: MAC Address: 00:22:07:32:A1:9C

eth1: MAC Address: 00:22:07:32:A1:9C

eth2: MAC Address: 00:22:07:32:A1:9C

eth3: MAC Address: 00:22:07:32:A1:9C

eth4: MAC Address: 00:22:07:32:A1:9C

�[0;34m[NTC arl] arlEnable : Enabled ARL binding to FAP�[0m

Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 Apr 22 2016 11:10:46 Registered <245>

--SMP support

wl: dsl_tx_pkt_flush_len=338

wl: high_wmark_tot=6149

PCI: Setting latency timer of device 0000:00:00.0 to 64

wl: passivemode=1

wl: napimode=0

wl0: allocskbmode=1 currallocskbsz=512

Neither SPROM nor OTP has valid image

wl:srom/otp not programmed, using main memory mapped srom info(wombo board)

wl:loading /etc/wlan/bcm6362_map.bin

srom rev:8

wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=16

wl0: Broadcom BCM435f 802.11 Wireless Controller 6.30.102.7.cpe4.12L08.0

dgasp: kerSysRegisterDyingGaspHandler: wl0 registered

Endpoint: endpoint_init entry

Endpoint: endpoint_init COMPLETED

p8021ag: p8021ag_init entry

Broadcom 802.1Q VLAN Interface, v0.1

===== Release Version DG150B_4.12NGT02.54 (build timestamp 160422_1113) =====

ssk:error:22.697:lck_checkBeforeEntry:225:lock reBOS: Enter bosInit

quired during cmBOS: Exit bosInit

sObj_getNextInSuendpoint_open COMPLETED

bTreeFlags
DDR Self Refresh pwrsaving is enabled

Adaptive Voltage Scaling is now enabled

BcmPwrMngtEnableAvs: AVS_START, 0x87acf258

Netfilter messages via NETLINK v0.30.

device eth0 entered promiscuous mode

ADDRCONF(NETDEV_UP): eth0: link is not ready

ip_tables: (C) 2000-2006 Netfilter Core Team

ip6_tables: (C) 2000-2006 Netfilter Core Team

device eth1 entered promiscuous mode

ADDRCONF(NETDEV_UP): eth1: link is not ready

device eth2 entered promiscuous mode

ADDRCONF(NETDEV_UP): eth2: link is not ready

device eth3 entered promiscuous mode

ADDRCONF(NETDEV_UP): eth3: link is not ready

device wl0 entered promiscuous mode

br0: port 5(wl0) entering forwarding state

WLmngr Daemon is running
optarg=0 shmId=0
wlevt is ready for new msg...
BcmAdsl_Initialize=0xC0263BB0, g_pFnNotifyCallback=0xC0298484

pSdramPHY=0xA7FFFFF8, 0xF7EFF6DF 0xDDDADF7D

*** XfaceOffset: 0x21F90 => 0x21F90 ***

*** PhySdramSize got adjusted: 0x8B980 => 0xA15BC ***

AdslCoreSharedMemInit: shareMemSize=387613(387616)

AdslCoreHwReset:  pLocSbSta=84540000 bkupThreshold=1600

AdslCoreHwReset:  AdslOemDataAddr = 0xA7F80170

***BcmDiagsMgrRegisterClient: 0 ***

dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered

fapDrv_psmAlloc: fapIdx=0, size: 1600, offset=b1012be0 bytes remaining 584

XTM Init: 200 rx BDs at 0xb1012be0

fapDrv_psmAlloc: fapIdx=0, size: 128, offset=b1013220 bytes remaining 456

XTM Init: 16 rx BDs at 0xb1013220

ADDRCONF(NETDEV_UP): eth4: link is not ready

Success
rcl_wanEthIntfObject: ethswctl -c hw-switching -o disable
monitor task is initialized pid= 334 

ssk:error:29.419:initVodslBoundIpIfWanSideUpLocked:766:Failed to get WAN Connection object
ssk:error:29.434:ssk_main:597:cannot handle msg type 0x10000802
There is no Predefined DevicePin in CFE
WPS Device PIN = 49385052
br0: port 5(wl0) entering disabled state

device wl0 left promiscuous mode

br0: port 5(wl0) entering disabled state

device wl0 entered promiscuous mode

br0: port 5(wl0) entering forwarding state

killall: hspotap: no process killed
br0: port 5(wl0) entering disabled state

Setting SSID: "NextGenTel_9F"
Setting SSID: "wl0_Guest1"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
wlctl: Unsupported
device wl0 left promiscuous mode

br0: port 5(wl0) entering disabled state

device wl0 entered promiscuous mode

br0: port 5(wl0) entering forwarding state

Note: Loading 6300 MDK (default) driver for 6362 chip 
Switch MDK: num_switches = 1
Switch MDK: unit = 0; phy_pbmp = 0x2f; config_pbmp = 0x2f 
Switch MDK link poll thread: unit=0; phypbmp=0x2f
tr69c:error:34.591:updateTr69cCfgInfo:750:could not build full path to (null)
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0x1001
600 sec

See also

ModelsDevices
Inteno DG150B • Wi-Fi 4 (Annex B)
Inteno DG301B • Wi-Fi 4