D-Link DAP-1533 rev A1

abgn (AN900)
Wireless N450 MediaBridge/Access Point
Support	Support page
Wikipedia	D-Link
WikiDevi.wi-cat.ru	D-Link DAP-1533 rev A1
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Status Unknown
Tomato any flavor	Incompatible
Platform
Brand • Model • Rev	D-Link DAP-1533 A1
FCC ID	KA2AP1533A1
IC ID	4216A-AP1533A1
Type	access point, bridge
CPU1	Atheros AR7370
CPU1 Type	MIPS 74Kc
CPU1 Speed	560 MHz
Flash1 Chip	Macronix MX25L6406EMI-12G
Flash1 Size	8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br />
RAM1 Size	128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Chip	ESMT M14D5121632A-2.5B x 2
ETH chip1	Atheros AR7370
Switch	Atheros AR8327N
Ethernet Port Count	4-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: none specified
Stock bootloader	U-Boot 1.1.4
Stock FW OS	Linux 2.6.31 LSDK-9.2.0_U8.834
Expansion IF types	USB 2.0
USB ports	1
USB Hub Compatible	Untested
Power	12 VDC, 2 A
Connector type	barrel
Serial Port (UART)	yes, 4-pad header
Flags: boot log
Other
Default IP address: 192.168.0.50 the IP 192.168.0.50 is used by 62 additional devices of which 62 are D-Link devices Default login user: Admin Default login password: blank Admin:blank credentials used by 82 additional devices of which 77 are D-Link devices
Manuf/OEM/ODM	Cameo
Retail
Availability	common
FCC approval date	09 November 2011
(Est.) release date	20 February 2012
UPC	790069357589 (UPC DB, On eBay)
ASIN	B007B5QQX2
Radio 1
Chip1	Atheros AR9380
Wireless interface OUI	none specified
Antenna Connector Type	U.FL
MIMO status	3x3:3
Wireless Standard	IEEE 802.11a/b/g/n
802.11n	up to 450 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	2.4 or 5 GHz

For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.

For a list of all currently documented D-Link device with specifications, see D-Link.

• 450 Mbps - 3SS 5GHz 802.11n (40MHz chan.),

• 450 Mbps - 3SS 2.4GHz 802.11n (40MHz chan.) = AN900 class

Overview

This device based on an AR7370 with ethernet switch AR8327N. RF based on depopulated an AR9380 5GHz radio. WiFi Certified

See also: Western Digital My Net Wi-Fi Range Extender

JTAG-Serial Info

Serial

Boot log

U-Boot 1.1.4 Rev: 20 (Nov 9 2011 - 19:56:29) U-boot DB120 DRAM: 128 MB Top of RAM usable for U-Boot at: 88000000 Reserving 162k for U-Boot at: 87fd4000 Reserving 192k for malloc() at: 87fa4000 Reserving 44 Bytes for Board Info at: 87fa3fd4 Reserving 36 Bytes for Global Data at: 87fa3fb0 Reserving 128k for boot params() at: 87f83fb0 Stack Pointer at: 87f83f98 Now running in RAM - U-Boot at: 87fd4000 id read 0x100000ff flash size 8MB, sector count = 128 Flash: 8 MB Using default environment In: serial Out: serial Err: serial Net: ag934x_enet_initialize... No valid address in Flash. Using fixed address wasp reset mask:c03300 WASP ----> S17 PHY * : cfg1 0x7 cfg2 0x7114 eth0: 00:03:7f:09:0b:ae athrs17_reg_init: complete eth0 up eth0 Hit any key to stop autoboot: 2 1 0 ## Booting image at 9f030000 ... Image Name: Linux Kernel Image Created: 2012-03-13 12:33:41 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1126377 Bytes = 1.1 MB Load Address: 80002000 Entry Point: 8024c9e0 Verifying Checksum at 0x9f030040 ...OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8024c9e0) ... ## bootargs 0: console=ttyS0,115200 root=31:03 mem=128M rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=ath-nor0:128k(u-boot),64k(nvram),1536k(linux),6144k(rootfs),192k(LANG),64k(MAC),64k(ART)... ## bootargs @A7F83FB0: console=ttyS0,115200 root=31:03 mem=128M rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=ath-nor0:128k(u-boot),64k(nvram),7680k(linux4),6528k@0x00150000(rootfs),192k(LANG),64k(MAC),64k(ART)... ## Giving linux memsize in bytes, 134217728 Starting kernel ... Booting Atheros AR934x Linux version 2.6.31--LSDK-9.2.0_U8.834 (root@david-VM) (gcc version 4.3.3 (GCC) ) #25 Tue Mar 13 20:26:18 CST 2012 flash_size passed from bootloader = 8 arg 1: console=ttyS0,115200 arg 2: root=31:03 arg 3: mem=128M arg 4: rootfstype=squashfs,jffs2 arg 5: init=/sbin/init arg 6: mtdparts=ath-nor0:128k(u-boot),64k(nvram),7680k(linux4),6528k@0x00150000(rootfs),192k(LANG),64k(MAC),64k(ART) CPU revision is: 0001974c (MIPS 74Kc) ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 480 ahb 240 Determined physical RAM map: memory: 02000000 @ 00000000 (usable) User-defined physical RAM map: memory: 08000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00008000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00008000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS0,115200 root=31:03 mem=128M rootfstype=squashfs,jffs2 init=/sbin/init mtdparts=ath-nor0:128k(u-boot),64k(nvram),7680k(linux4),6528k@0x00150000(rootfs),192k(LANG),64k(MAC),64k(ART) PID hash table entries: 512 (order: 9, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Writing ErrCtl register=00000000 Readback ErrCtl register=00000000 Memory: 126464k/131072k available (2376k kernel code, 4424k reserved, 657k data, 144k init, 0k highmem) NR_IRQS:128 plat_time_init: plat time init done Calibrating delay loop... 279.55 BogoMIPS (lpj=559104) Mount-cache hash table entries: 512 NET: Registered protocol family 16 PCI init:ath_pcibios_init ath_pcibios_init(294): PCI CMD write: 0x356 registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized pci 0000:00:00.0: PME# supported from D0 D1 D3hot pci 0000:00:00.0: PME# disabled Returning IRQ 64 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 ATH GPIOC major 0 athwdt_init: Registering WDT success 20000000, 1312D00, USEC_PER_SEC: 1000000,ath_ahb_freq: 240000000 squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 247 alg: No test for lzma (lzma-generic) alg: No test for stdrng (krng) io scheduler noop registered io scheduler deadline registered (default) HDLC line discipline maxframe=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A console [ttyS0] enabled brd: module loaded 7 cmdlinepart partitions found on MTD device ath-nor0 Creating 7 MTD partitions on "ath-nor0": 0x000000000000-0x000000020000 : "u-boot" 0x000000020000-0x000000030000 : "nvram" 0x000000030000-0x0000007b0000 : "linux4" 0x000000150000-0x0000007b0000 : "rootfs" 0x0000007b0000-0x0000007e0000 : "LANG" 0x0000007e0000-0x0000007f0000 : "MAC" 0x0000007f0000-0x000000800000 : "ART" TCP cubic registered NET: Registered protocol family 10 lo: Disabled Privacy Extensions NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> arch/mips/atheros/gpio.c (ath_simple_config_init) JUMPSTART_GPIO: 16 arch/mips/atheros/gpio.c: create_ar531x_gpio_proc_entry: WPS_LED GPIO = 12 ath_otp_init: Registering OTP success ath_clksw_init: Registering Clock Switch Interface success VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 144k freed init started: BusyBox v1.01 (2012.03.13-12:30+0000) multi-call binary init NVRAM_SPACE from mtdblock size init nvram memory map size: 0x10000 order of pages: 0x4 nvram module init: /dev/nvram major number 225 glues to mtd: "nvram" size: 0x00010000 nvram_space: 0x00010000 mapped via mmap(2) openfile :/etc/sysinfo new ver: 1.0 old ver: 1.0 new ver: 1.0 old ver: 1.0 openfile :/etc/sysinfo init artblock :lan_mac=28:10:7B:CA:77:15 to "sys_lan_mac" init artblock :wan_mac=28:10:7B:CA:77:16 to "sys_wan_mac" init artblock :hw_version=A1 to "sys_hw_version" init artblock :wlan0_domain=0x37 to "sys_wlan0_domain" ATHR_GMAC: Length per segment 1536 ATHR_GMAC: fifo cfg 3 01f00140 ATHR_GMAC: RX TASKLET - Pkts per Intr:16 ATHR_GMAC: Mac address for unit 0:bfff0000 ATHR_GMAC: ff:ff:ff:ff:ff:ff ATHR_GMAC: Max segments per packet : 1 ATHR_GMAC: Max tx descriptor count : 40 ATHR_GMAC: Max rx descriptor count : 232 ATHR_GMAC: Mac capability flags : 2381 athr_gmac_ring_alloc Allocated 640 at 0x87a17c00 athr_gmac_ring_alloc Allocated 3712 at 0x879b8000 WASP ----> S17 PHY * Setting Drop CRC Errors, Pause Frames and Length Error frames ### s17 : set 0x610=0x001bd560 ### s17 : set 0x614=0x80010002 ### s17 : set 0x610=0x001b7fe0 ### s17 : set 0x614=0x80020002 athrs17_reg_init:done Setting PHY... Phy setup Complete [az] 802.3az init done.. [az] 802.3az init done.. [az] 802.3az init done.. [az] 802.3az init done.. [az] 802.3az init done.. ADDRCONF(NETDEV_UP): eth0: link is not ready device eth0 is not a slave of br0 interface eth1 does not exist! device eth0.1 entered promiscuous mode device eth0 entered promiscuous mode AR934x GPIO Controller ################ change to AP or Client mode################ nvram_commit: size crc 10000 erasesize:10000, nvram->size: 80251640 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ATH_MAC_TIMER: enet unit:0 is up... RGMii 1000Mbps full duplex ATH_MAC_TIMER: done cfg2 0x7215 ifctl 0x0 miictrl ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Port Status 1c000004 ath-ehci ath-ehci.0: ATH EHCI ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1 ehci_reset Intialize USB CONTROLLER in host mode: 13 ehci_reset Port Status 1c000000 ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000 ehci_reset Intialize USB CONTROLLER in host mode: 13 ehci_reset Port Status 1c000000 ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected insmod: cannot open module `/lib/modules/2.6.31--LSDK-9.2.0_U8.834/kernel/drivers/usb/host/ohci-hcd.ko': No such file or directory Please press Enter to activate this console. ########################## sysinit #########################service init rc:service_init:init_nvram:start insmod: cannot insert `/lib/devnvram.ko': File exists (-1): File exists openfile :/var/etc/nvram.default rc:service_init:init_nvram:end configuration_version_control: configuration_version= in NVRAM configuration_version_control: configuration_version=1.0 in System =============insert_switch_mod()============== insert_switch_mod: insmod /lib/modules/2.6.31/net/athrs_gmac.ko insmod: cannot insert `/lib/modules/2.6.31/net/athrs_gmac.ko': File exists (-1): File exists device eth0 left promiscuous mode eth0.1: Cannot assign requested address device eth0 entered promiscuous mode eth0.1: Cannot assign requested address eth0.2: Cannot assign requested address eth0.2: Cannot assign requested address device br0 already exists; can't create bridge with the same name device eth0.1 is already a member of a bridge; can't enslave it to bridge br0. br0: port 1(eth0.1) entering forwarding state sh: ./etc/rc.d/pre_customer.sh: not found Wed Mar 14 17:50:00 UTC 2012 modprobe: could not parse modules.dep modprobe: could not parse modules.dep SLIDE on 5GHz Accece Point /tmp/password has been created 2012-03-14 17:50:00: (network.c.239) warning: please use server.use-ipv6 only for hostnames, not without server.bind / empty address; your config will break if the kernel default for IPV6_V6ONLY changes sh: dcc: not found RC Main Loop: START rc is BUSY now! AP Mode or AP Client Mode only need LAN Setting Start LAN start_lan():Support AP and Router Mode Switch killall: udhcpc: no process killed ==========start_ap_lan============ killall: lanmon: no process killed route_add: ifname=br0,rt_destaddr=0.0.0.0,rt_netmask=0.0.0.0,rt_gateway=192.168.1.1,rt_metric=0 route_add: ifname=lo,rt_destaddr=127.0.0.0,rt_netmask=255.0.0.0,rt_gateway=0.0.0.0,rt_metric=0 ##################### wlan1_enable######################### Loading Wireless Modules: country_Code=276 ##########################Loading Wireless Modules: country_Code=276 load DB120 asf: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved ath_pci: 9.2.0_U8.834 (Atheros/multi-bss) __ath_attach: Set global_scn[0] ACBKMinfree = 48 ACBEMinfree = 32 ACVIMinfree = 16 ACVOMinfree = 0 CABMinfree = 48 UAPSDMinfree = 0 Restoring Cal data from Flash eepromVersion: 02, templateVersion: 02 custData: [ar9300]TxGainTableApply--OSPREY dfs_attach: use DFS enhancements DFS min filter rssiThresh = 18 DFS max pulse dur = 151 ticks ath_get_caps[4834] rx chainmask mismatch actual 7 sc_chainmak 0 ath_get_caps[4809] tx chainmask mismatch actual 7 sc_chainmak 0 SC Callback Registration for wifi0 wifi0: Atheros 9380: mem=0x10000000, irq=64 hw_base=0xb0000000 DFS min filter rssiThresh = 22 DFS max pulse dur = 151 ticks Loading Wireless Modules: end set_wlan_mac: start set_wlan_mac: end ##################### set client mode ########################### start_makeVAP: ath_count=0, wds_enable=0, apifnum=0:RF:48:11NAHT40MINUS:1, op_mode=AP start_makeVAP: Ifnum=0, set_RF=RF, Pri_Ch=48, Ch_Mode=11NAHT40MINUS, pure_mode=1, op_mode=AP wlan_vap_create : enter. devhandle=0x871002c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 wlan_vap_create : exit. devhandle=0x871002c0, opmode=IEEE80211_M_HOSTAP, flags=0x1. VAP device ath0 created ath0 Invalid command : extoffset DES SSID SET=dlink ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 start_makeVAP: end DES SSID SET=default start_activateVAP: ath_count=0, guest_zone=2, netusb_guest_zone=2 device ath0 entered promiscuous mode br0: port 2(ath0) entering forwarding state device eth0.1 left promiscuous mode br0: port 1(eth0.1) entering disabled state device eth0.1 entered promiscuous mode br0: port 1(eth0.1) entering forwarding state Unknown command: 6to4, use subcommands below dhcp6c : dhcp6c command rdnssd : rdnssd command autoconfig : autoconfig mode start : Start AP IPv6 setting stop : Clean AP IPv6 configuration cli build Dec 9 2011 12:04:53 Unknown command: 6rd, use subcommands below dhcp6c : dhcp6c command rdnssd : rdnssd command autoconfig : autoconfig mode start : Start AP IPv6 setting stop : Clean AP IPv6 configuration cli build Dec 9 2011 12:04:53 Using Switch Chip to find all mac address #################################Start WLAN Finished############################ TFTPD start and listen on port 69. ntp1.dlink.com: Unknown host usbcore: registered new interface driver sxuptp_generic usbcore: registered new interface driver sxuptp_ipod start_route sh: iptables: not found sh: iptables: not found sh: iptables: not found sh: iptables: not found sh: iptables: not found sh: iptables: not found QoS disabled Reading topology file /var/tmp/topology.conf ... 409.860: Reading bss configuration file /var/tmp/WSC_ath0.conf ... ieee80211_ioctl_siwmode: imr.ifm_active=1376896, new mode=3, valid=1 br0: port 2(ath0) entering disabled state Using interface ath0 with hwaddr 28:10:7b:ca:77:15 and ssid 'default' Failed to kill daemon: No such file or directory IDLE rc is IDLE now! DES SSID SET=default br0: port 2(ath0) entering forwarding state 410.661: upnp_wps_device_init called l2_packet_receive - recvfrom: Network is down

Pictures

User Images

• 

  PCB top

• 

  PCB bottom

• 

  Modified with external RP-SMA Connectors

• 

  CPU

• 

  Flash

• 

  Memory

• 

  Radio

• 

  Switch