Ubiquiti Networks EdgeSwitch 8XP (ES-8XP)
From TechInfoDepot
Jump to navigationJump to search| 3rd Party Firmware | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| dd-wrt |
Status Unknown | ||||||||||||
| OpenWrt | |||||||||||||
| Tomato any flavor |
Incompatible | ||||||||||||
| Gargoyle |
Status Unknown | ||||||||||||
| Platform | |||||||||||||
| Brand • Model • Rev |
Ubiquiti Networks EdgeSwitch 8XP (ES-8XP) | ||||||||||||
| CPU1 |
Atheros AR7242 | ||||||||||||
| CPU1 Type |
MIPS 24Kc | ||||||||||||
| CPU1 Speed |
390 MHz | ||||||||||||
| Flash1 Size |
8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> | ||||||||||||
| RAM1 Size |
64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> | ||||||||||||
| ETH chip1 |
Brand? Model? | ||||||||||||
| Switch |
Broadcom BCM53128 | ||||||||||||
| Ethernet Port Count |
8-1GbE | ||||||||||||
| Ethernet connector |
8P8C | ||||||||||||
| Wired Standard |
IEEE 802.3i/3u/3ab | ||||||||||||
| Auto-MDIX |
unspecified | ||||||||||||
| Switch Class |
managed | ||||||||||||
|
Ethernet OUI: none specified | |||||||||||||
| Expansion IF types |
USB 2.0 | ||||||||||||
| Stock bootloader |
U-Boot | ||||||||||||
| PoE |
802.3at, 802.3af, standard | ||||||||||||
| Power |
24-48 VDC, ? A | ||||||||||||
| Serial Port (UART) |
yes, 115200 / 8N1 | ||||||||||||
|
| |||||||||||||
| 3rd Party Firmware Support | |||||||||||||
| |||||||||||||
For a list of all currently documented Atheros (QCA) chipsets with specifications, see Atheros.
For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.
For a list of all currently documented Ubiquiti Networks device with specifications, see Ubiquiti Networks.
Flashing
 | NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing OpenWrt
 | The development branch can contain experimental code that is under active development and should not be used for production environments. Snapshot images may support additional hardware; however, it is experimental, considered unstable, and sometimes won't compile. |
| Prebuilt snapshot images do not come with any web interface or GUI. You will need to be comfortable using a command line and remote shell to install one yourself → How to install LuCI |
| This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 8MB FLASH / 64MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 8/64 warning for details. This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation. This means that you will not be able to install many packages, and that you might experience crashes due to OOM situations more or less often. See OpenWrt on 8/64 devices what you can do now. |
On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki
OpenWrt Target: ath79
OpenWrt Subtarget: generic
OpenWrt Package architecture: mips_24kc
Support started version: 21.02.0
Current supported version: snapshot
On the OpenWrt Wiki
OpenWrt Target: ath79
OpenWrt Subtarget: generic
OpenWrt Package architecture: mips_24kc
Support started version: 21.02.0
Current supported version: snapshot
The Ubiquiti ToughSwitch 8XP is a 8-port PoE Gigabit switch with a single Fast-Ethernet management port. It supports both 24V passive PoE and 48V 802.11af/at PoE out on all eight ports. By default the single Fast-Ethernet port labeled "MGMT" is configured as the WAN port. Thus access to the device is only possible via the eight switch ports. Installation of the firware is possible either via serial + tftpboot or the factory firmware update function via webinterface. Serial: 3v3 115200 8n1 The serial header is located in the lower left corner of the switches PCB: | | | | o | o RX | o TX | o GND | |
