Netgear WNDR3700v5

multiple revisions of this device, use caution

abgn (AN600)
N600 Wireless Dual Band Gigabit Router
Homepage	Product page
Wikipedia	Netgear
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Supported
Tomato any flavor	Incompatible
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	Netgear WNDR3700 v5
FCC ID	PY314200274, PY314200275
IC ID	4054A-14200275
Board ID	AYB00D-1.6MM
Type	wireless router
CPU1	MediaTek MT7621ST
CPU1 Type	MIPS 1004Kc
CPU1 Speed	880 MHz 16-bit
Flash1 Chip	Macronix MX25L12835FMI-10G
Flash1 Size	16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br />
RAM1 Size	128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Chip	Nanya NT5CB64M16FP-DP
ETH chip1	MediaTek MT7621ST
Switch	MediaTek MT7621ST
Ethernet Port Count	1-1GbE-WAN 4-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: none specified
Stock bootloader	U-Boot 1.1.3 Ralink 4.2.1.0
Stock FW OS	Linux 2.6.36
Expansion IF types	Mini PCIe, USB 2.0
USB ports	1
USB Hub Compatible	Untested
Power	12 VDC, 1.5 A
Connector type	barrel
Serial Port (UART)	yes, 4-pin header
Additional chips 5GHz 23dBm Power Amplifier w/ Power Detector;Skyworks (SiGe);SE5003L;;2; 5GHz SPDT Switch w/ LNA;Skyworks;SKY85601;;2;
Other
Default login user: admin Default login password: password admin:password credentials used by 425 additional devices of which 306 are Netgear devices
Manuf/OEM/ODM	SerComm
3rd Party Firmware Support	Padavan ? (+ac), OpenWrt • (List | Dev | DLs)
Retail
Availability	common
FCC approval date	04 December 2014
ASINs	B002HWRJY4 B002HWRJY4 B0071U0ZRU ,  multiple uses
Country of manuf	China
Radio 1
Chip1	MediaTek MT7603EN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 300 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio 2
Chip1	MediaTek MT7612EN
Wireless interface OUI	none specified
Antenna Connector Type	none specified
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
FCC ID Netgear R6220 PY314200274 Netgear R6230 PY314200274 Netgear WAC104 PY314200274
CPU1 brand Radio1 chip1 brand Radio2 chip1 brand Netgear WNDR3700v1 Atheros Atheros Atheros Netgear WNDR3700v2 Atheros Atheros Atheros Netgear WNDR3700v3 Broadcom Broadcom Broadcom Netgear WNDR3700v4 Atheros Atheros Atheros Netgear WNDR3700v5 MediaTek MediaTek MediaTek

For a list of all currently documented MediaTek chipsets with specifications, see MediaTek.

For a list of all currently documented Netgear device with specifications, see Netgear.

• 300 Mbps - 2SS 5GHz 802.11n (40MHz chan.),

• 300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = AN600 class

Overview

"AYB00D-1.6MM" is silkscreened on the board in the images.

See also: Netgear R6220 and SerComm

This device was under short-term confidentiality, but that expired 06/01/2015 ⚠.

Links of Interest

• On the OpenWrt wiki
• On OpenWrt forums

Flashing

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki
On the OpenWrt Forum
OpenWrt Target: ramips
OpenWrt Subtarget: mt7621
OpenWrt Package architecture: mipsel_24kc
Support started version: 17.01.0
Current supported version: 23.05.5

Please insert instructions here

JTAG-Serial Info

Serial

boot log

=================================================================== MT7621 stage1 code 13:14:00 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL4 FB_DL: 0x10, 1/0 = 657/367 41000000 PLL2 FB_DL: 0x16, 1/0 = 585/439 59000000 PLL3 FB_DL: 0x16, 1/0 = 678/346 59000000 do DDR setting..[00320000] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 000E:| 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 000F:| 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 72 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_R0DELDLY[018]=00001F1F ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 13 10 14 13 14 11 15 9 6 11 10 | 9 13 10 14 9 13 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =31 DQS1 = 31 ================================================================== bit DQS0 bit DQS1 0 (1~60)30 8 (1~58)29 1 (1~58)29 9 (1~57)29 2 (1~60)30 10 (1~60)30 3 (1~58)29 11 (1~56)28 4 (1~60)30 12 (1~58)29 5 (2~60)31 13 (1~57)29 6 (1~61)31 14 (1~61)31 7 (1~60)30 15 (1~59)30 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 14 12 15 15 15 11 15 10 8 13 10 | 10 15 12 15 9 14 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0800 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 DQS loop = 14, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[1]=14, finish count=2 DQ loop=15, cmp_err_1 = ffff01a2 DQ loop=14, cmp_err_1 = ffff0180 DQ loop=13, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=13, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=13, finish count=2 byte:0, (DQS,DQ)=(9,8) byte:1, (DQS,DQ)=(8,8) 20,data:89 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Nov 17 2014 - 08:29:53) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87fb4000 Config XHCI 40M PLL flash manufacture id: c2, device id 20 18 find flash: MX25L12805D *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.2.1.0 -------------------------------------------- ASIC MT7621AS (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: SPI Flash Date:Nov 17 2014 Time:08:29:53 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes Reset switch ... #Reset_MT7530 set LAN/WAN LLLLW Example expects ABI version 2 Actual U-Boot ABI version 2 ****************************************** Uboot StandAlone Entry ****************************************** 0, cmd 1, 0x0000000D cmd : 0x0000000D Press Ctrl+C to Enter the Main loop... Example expects ABI version 2 Actual U-Boot ABI version 2 ****************************************** Uboot StandAlone Entry ****************************************** 0, cmd 1, 0x0000000F cmd : 0x0000000F Enter NMRP_main Flash Sector Number : 256. NetTxPacket = 0x87FE4300 KSEG1ADDR(NetTxPacket) = 0xA7FE4300 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) Waitting for RX_DMA_BUSY status Start... done ETH_STATE_ACTIVE!! NMRP_FLASH_SIZE_buffer --> a1000000. NMRP:LISTENING ### No NMRP Server found ### Example expects ABI version 2 Actual U-Boot ABI version 2 ****************************************** Uboot StandAlone Entry ****************************************** 0, boot Flash Sector Number : 256. *************************************************** Sercomm Boot Version 1.13.0 *************************************************** Entering Firmware : Everything is OK. flash base: 0xbfc00000, kernel addr :0xbfc50000, bootloader size: 0x30000, config size 0x10000, fac size : 0x10000 kernel addr :0xbfc50000 System Boot system code via Flash. ## Booting image at bfc50000 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2404943 Bytes = 2.3 MB Load Address: 80001000 Entry Point: 8000f500 Verifying Checksum ... OK Uncompressing Kernel Image ... OK commandline in boot is : <NULL> !!!! No initrd ## Transferring control to Linux (at address 8000f500) ... ## Giving linux memsize in MB, 128 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.36 (root@localhost.localdomain) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Tue Nov 18 18:47:38 CST 2014 The CPU feqenuce set to 880 MHz GCMP present CPU revision is: 0001992f (MIPS 1004Kc) Software DMA cache coherency Determined physical RAM map: memory: 08000000 @ 00000000 (usable) Zone PFN ranges: Normal 0x00000000 -> 0x00008000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00008000 avail: cpu2 is not ready avail: cpu3 is not ready Detected 1 available secondary CPU(s) PERCPU: Embedded 7 pages/cpu @81103000 s7104 r8192 d13376 u65536 pcpu-alloc: s7104 r8192 d13376 u65536 alloc=16*4096 pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3 console=ttyS0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Writing ErrCtl register=00049021 Readback ErrCtl register=00049021 Memory: 122600k/131072k available (5108k kernel code, 8472k reserved, 1643k data, 212k init, 0k highmem) Hierarchical RCU implementation. Verbose stalled-CPUs detection is disabled. NR_IRQS:128 Trying to install interrupt handler for IRQ24 Trying to install interrupt handler for IRQ25 Trying to install interrupt handler for IRQ22 Trying to install interrupt handler for IRQ9 Trying to install interrupt handler for IRQ10 Trying to install interrupt handler for IRQ11 Trying to install interrupt handler for IRQ12 Trying to install interrupt handler for IRQ13 Trying to install interrupt handler for IRQ14 Trying to install interrupt handler for IRQ16 Trying to install interrupt handler for IRQ17 Trying to install interrupt handler for IRQ18 Trying to install interrupt handler for IRQ19 Trying to install interrupt handler for IRQ20 Trying to install interrupt handler for IRQ21 Trying to install interrupt handler for IRQ23 Trying to install interrupt handler for IRQ26 Trying to install interrupt handler for IRQ27 Trying to install interrupt handler for IRQ28 Trying to install interrupt handler for IRQ15 Trying to install interrupt handler for IRQ8 Trying to install interrupt handler for IRQ29 Trying to install interrupt handler for IRQ30 Trying to install interrupt handler for IRQ31 console [ttyS1] enabled Calibrating delay loop... 579.58 BogoMIPS (lpj=1159168) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 launch: starting cpu1 launch: cpu1 gone! CPU revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Brought up 2 CPUs Synchronize counters across 2 CPUs: done. NET: Registered protocol family 16 release PCIe RST: RALINK_RSTCTRL = 7000000 PCIE PHY initialize ***** Xtal 40MHz ***** start MT7621 PCIe register access RALINK_RSTCTRL = 7000000 RALINK_CLKCFG1 = 77ffeff8 *************** MT7621 PCIe RC mode ************* PCIE1 no card, disable it(RST&CLK) pcie_link status = 0x5 RALINK_RSTCTRL= 5000000 *** Configure Device number setting of Virtual PCI-PCI bridge *** RALINK_PCI_PCICFG_ADDR = 21007f2 -> 12007f2 PCIE0 enabled PCIE2 enabled interrupt enable status: 500000 Port 1 N_FTS = 1b105000 Port 0 N_FTS = 1b105000 config reg done init_rt2880pci done bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff] pci 0000:00:00.0: BAR 1: set to [mem 0x60300000-0x6030ffff] (PCI address [0x60300000-0x6030ffff] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff] pci 0000:00:01.0: BAR 1: set to [mem 0x60310000-0x6031ffff] (PCI address [0x60310000-0x6031ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] pci 0000:01:00.0: BAR 0: set to [mem 0x60000000-0x600fffff 64bit] (PCI address [0x60000000-0x600fffff] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [io disabled] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff] pci 0000:02:00.0: BAR 0: set to [mem 0x60200000-0x602fffff] (PCI address [0x60200000-0x602fffff] pci 0000:00:01.0: PCI bridge to [bus 02-02] pci 0000:00:01.0: bridge window [io disabled] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] pci 0000:00:01.0: bridge window [mem pref disabled] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) PCI: Enabling device 0000:00:01.0 (0004 -> 0006) BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60300000 res[1]->end = 6030ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 BAR0 at slot 1 = 0 bus=0x0, slot = 0x1 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60310000 res[1]->end = 6031ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0, irq=0x4 res[0]->start = 60000000 res[0]->end = 600fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x2, slot = 0x1, irq=0x19 res[0]->start = 60200000 res[0]->end = 602fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource MIPS NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 128 (order: 0, 4096 bytes) UDP-Lite hash table entries: 128 (order: 0, 4096 bytes) NET: Registered protocol family 1 4 CPUs re-calibrate udelay(lpj = 1167360) squashfs: version 4.0 (2009/01/31) Phillip Lougher fuse init (API version 7.15) SGI XFS with security attributes, large block/inode numbers, no debug enabled SGI XFS Quota Management subsystem msgmni has been set to 239 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) Ralink gpio driver initialized spidrv_major = 217 i2cdrv_major = 218 spdif_mod_init: start SPDIF module Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A brd: module loaded flash manufacture id: c2, device id 20 18 MX25L12805D(c2 2018c220) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 20 MTD partitions on "raspi": 0x000000000000-0x000000040000 : "Bootloader" 0x000000040000-0x000000050000 : "SC PID" 0x000000050000-0x0000002d0000 : "Kernel" 0x0000002d0000-0x000000e70000 : "Rootfs" 0x000000e70000-0x000000e90000 : "English UI" 0x000000e90000-0x000000eb0000 : "ML1" 0x000000eb0000-0x000000ed0000 : "ML2" 0x000000ed0000-0x000000ef0000 : "ML3" 0x000000ef0000-0x000000f10000 : "ML4" 0x000000f10000-0x000000f30000 : "ML5" 0x000000f30000-0x000000f40000 : "Factory" 0x000000f40000-0x000000f50000 : "SC Private Data" 0x000000f50000-0x000000f60000 : "POT" 0x000000f60000-0x000000f80000 : "Traffic Meter" 0x000000f80000-0x000000f90000 : "DPF" 0x000000f90000-0x000000fa0000 : "SC Nvram" 0x000000fa0000-0x000000fb0000 : "Ralink Nvram" 0x000000fb0000-0x000000fd0000 : "Ralink Reserved" 0x000000fd0000-0x000000ff0000 : "ML6" 0x000000ff0000-0x000001000000 : "Upgrade Flag" rdm_major = 253 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288021 Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288028 PROC INIT OK! PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 IMQ driver loaded successfully. Hooking IMQ before NAT on PREROUTING. Hooking IMQ after NAT on POSTROUTING. usbcore: registered new interface driver net1080 register mt_drv === pAd = c0182000, size = 586072 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0080000, csr_addr=0xc0080000! device_id =0x7603 RtmpChipOpsHook(502): Not support for HIF_MT yet! mt7603_init()--> mt_bcn_buf_init(224): Not support for HIF_MT yet! <--mt7603_init() FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) xhc_mtk xhc_mtk: xHCI Host Controller xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 1 xhc_mtk xhc_mtk: irq 22, io mem 0x1e1c0000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhc_mtk xhc_mtk: xHCI Host Controller xhc_mtk xhc_mtk: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1915 buckets, 7660 max) nf_conntrack_rtsp v0.6.21 loading IPVS: Registered protocols () IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: ipvs loaded. GRE over IPv4 demultiplexor driver gre: can't add protocol nf_nat_rtsp v0.6.21 loading ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone TCP cubic registered NET: Registered protocol family 10 NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NOTIFY NOTIFY NOTIFY NOTIFY NET: Registered protocol family 17 L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 L2TP IP encapsulation support (L2TPv3) L2TP netlink interface L2TP ethernet pseudowire support (L2TPv3) 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 212k freed init started: BusyBox v1.12.1 (2014-11-18 18:59:14 CST) starting pid 58, tty '': '/usr/etc/rcS' Algorithmics/MIPS FPU Emulator v1.5 mount: mounting none on /dev/pts failed: No such file or directory Welcome to _______ _______ ___ __ ____ _ _ ___ | ___ \| __ || | |__|| \ | || | / / | |___| || |__| || |__ __ | \| || |/ / | _ /| _ || || || |\ || \ |__| \__\|__| |__||______||__||_| \____||_|\___\ =System Architecture Department= [rc debug]/sbin/rc reg_init [rc.c::configure_mt7621_register():1011] set from jtag to gpio mode [SYSTEM]/sbin/reg s 0 switch register base addr to system register 0xbe000000 [SYSTEM]/sbin/reg r0x405a9 0x60 [SYSTEM]/sbin/reg write offset 0x60, value 0x405a8 w 0x60 0x405a8 [SYSTEM]/sb0x405a8 in/reg r 0x60 [SYSTEM]/bin/echo 1 > /NOTIFY prNOTIFY ocNOTIFY /NOTIFY sNOTIFY ysNOTIFY /NOTIFY net/ipv6/conf/all/disable_ipv6 led_pb_api: module license 'Sercomm' taints kernel. Disabling lock debugging due to kernel taint Register LED ID <75> Register LED ID <70> Register LED ID <20> Register LED ID <40> Register LED ID <45> Register LED ID <60> Register LED ID <61> Register LED ID <62> Register LED ID <90> Register LED ID <91> Register LED ID <92> insmod: can't read '/lib/modules/2.6.30.9/kernel/fs/jbd2/jbd2.ko': No such file or directory insmod: can't read '/lib/modules/2.6.30.9/kernel/fs/ext4/ext4.ko': No such file or directory netfilter dnshj choose interested dns queries module loaded ! insmod: can't read '/lib/modules/ipt_macblock_dnshj.ko': No such file or directory init common module successful insert firewall block module success fake source dos protect modules is inserted netfilter PSD and TCP/UDP Echo/Chargen Attack loaded netfilter tcp syn flood module loaded netfilter clamp total session for one src ip module loaded netfilter other dos module loaded insmod finish NOTIFY NOTIFY NOTIFY Raeth v3.1 (Tasklet,SkbRecycle) phy_tx_ring = 0x06de8000, tx_ring = 0xa6de8000 phy_rx_ring0 = 0x06dea000, rx_ring0 = 0xa6dea000 change HW-TRAP to 0x15c8f set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288028 GDMA2_MAC_ADRH -- : 0x0000000c GDMA2_MAC_ADRL -- : 0x43288045 NOTIFY NOTIFY eth3: ===> VirtualIF_open CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 NOTIFY NOTIFY NOTIFY insmod: can't read '/lib/modules/2.6.36/kernel/drivers/net/wireless/MT7610_ap/MT7610_ap.ko': No such file or directory register rt2860 === pAd = c0902000, size = 1348584 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0800000, csr_addr=0xc0800000! device_id =0x7662 ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=2 NVM is FLASH mode NOTIFY NOTIFY [rc debug]/usr/sbin/rc init [SYSTEM]/sbin/ifconfig NOTIFY br0 NOTIFY doNOTIFY wn hw ether A4:2B:8C:58:FA:38 up [SYSTEM]/sbin/ifconfig eth2.1 down ifconfig: SIOCGIFFLAGS: No such device [SYSTEM]/sbinNOTIFY /ifconfig eth2.2 down ifconfig: ra2880stop()...SDone IOeth3: ===> VirtualIF_close CGIFFFree TX/RX Ring Memory! LAGS:NOTIFY No such device [SYSTEM]/sbin/ifconfig eth2 down [SYSTEM]/sbin/vconfig rem eth2.1 vconfig: ioctl error for rem: No sucNOTIFY hRaeth v3.1 ( dTasklete,SkbRecyclev) ice phy_tx_ring = 0x06590000, tx_ring = 0xa6590000 phy_rx_ring0 = 0x065ac000, rx_ring0 = 0xa65ac000 [SYSTEM]/sbin/vconfig rem eth2.2 vconfig: ioctl error for rem: Nochange HW-TRAP to 0x15c8f such deviceset LAN/WAN LLLLW [SYSTEM]/sbiGMAC1_MAC_ADRH -- : 0x0000000c nGMAC1_MAC_ADRL -- : 0x43288028 /ieth3: ===> VirtualIF_open fCDMA_CSG_CFG = 81000000 cGDMA1_FWD_CFG = 20710000 oGDMA2_FWD_CFG = 20710000 nfigNOTIFY eth2 up [SYSTEM]/sbin/ifconfiNOTIFY g eth2 down ra2880stop()...Done eth3: ===> VirtualIF_close Free TX/RX Ring Memory! NOTIFY [SYSTEM]/sbin/ifconfig eNOTIFY NOTIFY ether A4:2B:8C:58:FA:38 Raeth v3.1 (asklet3,SkbRecycle2) m[S phy_tx_ring = 0x06590000, tx_ring = 0xa6590000 YSTEM]/ phy_rx_ring0 = 0x06594000, rx_ring0 = 0xa6594000 sbin/ifconfig eth2 up change HW-TRAP to 0x15c8f set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x0000a42b GMAC1_MAC_ADRL -- : 0x8c58fa38 eth3: ===> VirtualIF_open CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 NOTIFY [SYSTEM]/usr/sbin/config-vlan.sh 3 0 restore GSW to dump switch mode switch reg write offset=2004, value=ff0000 switch reg write offset=2104, value=ff0000 switch reg write offset=2204, value=ff0000 switch reg write offset=2304, value=ff0000 switch reg write offset=2404, value=ff0000 switch reg write offset=2504, value=ff0000 device eth2 entered promiscuous modeff0000 sbr0: port 1(eth2) entering learning state wibr0: port 1(eth2) entering learning state tch reg write offset=2704, value=ffNOTIFY 0eth3: ===> VirtualIF_open 00NOTIFY 0 switch reg write offset=2010, value=810000c0 switch reg write offset=2110, value=810000c0 switch reg write offset=2210, value=810000c0 switch reg write offset=2310, value=810000c0 switch reg write offset=2410, value=810000c0 switch reg write offset=2510, value=810000c0 switch reg write offset=2610, value=810000c0 switch reg write offset=2710, value=810000c0 REG_ESW_WT_MAC_ATC is 0x7ff0002 done. [SYSTEM]/sbin/brctl addif br0 eth2 [SYSTEM]/sbin/ifconfig eth3 up RC: wifi_init() rules = <>, timeout = 20 [SYSTEM]/usr/bin/killall access_logd killall: access_logd: no process killed [SYSTEM]/usr/sbin/rc access_log start [rc debug]/usr/sbin/rc access_log start ap_name=access_log action=start [rc.c::rc_action():803] rc_action before add access_log - start rc action <access_log @ start> before file_lock. rc action <access_log @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_log.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add access_log - start unlink running file </var/run/rc.access_log.run> [rc.c::rc_action():803] rc_action before add access_log - start rc action <access_log @ start> before file_lock. rc action <access_log @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_log.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add access_log - start unlink running file </var/run/rc.access_log.run> can't find this application [rc.c::rc_action():803] rc_action before add access_log - start rc action <access_log @ start> before file_lock. rc action <access_log @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_log.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add access_log - start [rc.c::rc_start():706] Calling Start function of access_log killall: access_logd: no process killed Access Control log start. Access Control socket create unlink running file </var/run/rc.access_log.run> [SYSTEM]/usr/sbin/rc access_dev start [rc debug]/usr/sbin/rc access_dev start ap_name=access_dev action=start [rc.c::rc_action():803] rc_action before add access_dev - start rc action <access_dev @ start> before file_lock. rc action <access_dev @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_dev.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add access_dev - start unlink running file </var/run/rc.access_dev.run> [rc.c::rc_action():803] rc_action before add access_dev - start rc action <access_dev @ start> before file_lock. rc action <access_dev @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_dev.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add access_dev - start unlink running file </var/run/rc.access_dev.run> can't find this application [rc.c::rc_action():803] rc_action before add access_dev - start rc action <access_dev @ start> before file_lock. rc action <access_dev @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.access_dev.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add access_dev - start [rc.c::rc_start():706] Calling Start function of access_dev killall: access_devinfo: no process killed Access Control socket create unlink running file </var/run/rc.access_dev.run> [modelinfo_product_id.c::modelinfo_map_index():74] 0x30 0x32, 0x3032. [modelinfo_product_id.c::modelinfo_map_index():118] find index 1 for modelinfo_get_product_name [modelinfo_product_id.c::modelinfo_set_autoupg_fileinfo():185] autoupg_fileinfo_in_nv is wndr3700v5_fileinfo.txt [SYSTEM]/usr/bin/insmod /lib/modules/ufsd.ko ufsd:: trace mask set to 0000000f ufsd: driver (lke_9.0.0 lke_9.0.0_r237695_b2, LBD=ON, ioctl, bdi, sd2(0), wb, bz, tr) loaded at c0b02000 NTFS support included optimized: speed Build_for__Netgear_R6220_k2.6.36_2014-10-22_lke_9.0.0_r237695_b2 =============rc start [rc debug]/usr/sbin/rc lan start ap_name=lan action=start [rc.c::rc_action():803] rc_action before add lan - start rc action <lan @ start> before file_lock. rc action <lan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.lan.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add lan - start [rc.c::rc_start():706] Calling Start function of lan [SYSTEM]/usr/sbin/brctl setfd br0 1 [SYSTEM]/sbin/ifconfig br0 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255 [SYSTEM]/usr/sbin/brctl stp br0 off [SYSTEM]/usr/sbin/brctl stp br0 off sh: cannot create /proc/http_file/getLanIp: nonexistent directory unlink running file </var/run/rc.lan.run> [rc debug]/usr/sbin/rc wlan start ap_name=wlan action=start [rc.c::rc_action():803] rc_action before add wlan - start rc action <wlan @ start> before file_lock. rc action <wlan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.wlan.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add wlan - start [rc.c::rc_start():706] Calling Start function of wlan [wifi_mtk/wifi.c::sync_wireless_nvram():1495] wifi_super_wifi_enable:0, wifi_powerpercent:100, wifi_super_wifi_enable1:0, wifi_powerpercent1:100 [modelinfo_product_id.c::modelinfo_map_index():74] 0x30 0x32, 0x3032. [modelinfo_product_id.c::modelinfo_map_index():118] find index 1 for modelinfo_get_product_name [wifi_mtk/wifi.c::start_wireless():1525] SC 5G support level: 11n [SYSTEM]mkdir -p /etc/Wireless/RT2860 [flash.c::sc_check_remotescfgmgrmagic():794] buf:ff, ff, ff, ff [flash.c::sc_check_remotescfgmgrmagic():796] magic:31, 3e, c5, 8d scfgmgr for local [SYSTEM]mkdir -p /etc/Wireless/iNIC region flag in flash:00 00 00 02 [SYSTEM]/bin/mkdir -p /etc/Wireless/RT2860AP/ [SYSTEM]/bin/mkdir -p /etc_ro/Wireless/RT2860AP/ region is PR:0 [SYSTEM]/bin/cp -f /etc_ro/wlan/MT7612E_EEPROM.bin.11n /etc_ro/wlan/MT7612E_EEPROM.bin [wifi_mtk/wifi.c::map_singleskutmp_by_region():1251] all region singlesku.dat exist [SYSTEM]/bin/rm /etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620 >/dev/console 2>&1 rm: cannot remove '/etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620': No such file or directory [SYSTEM]/bin/rm /etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E >/dev/console 2>&1 rm: cannot remove '/etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E': No such file or directory [wifi_mtk/wifi.c::map_singleskutmp_by_region():1268] wifi gui region is Europe, 2g CE, 5g CE [wifi_mtk/wifi.c::map_singleskutmp_by_region():1306] region NOT PR or RU [SYSTEM]/bin/cp -rf /usr/etc_ro/Wireless/singlesku_dat//CE/SingSku-2.4.txt /etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620 >/dev/console 2>&1 [SYSTEM]/bin/cp -rf /usr/etc_ro/Wireless/singlesku_dat//CE/SingSku-5G.txt /etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E >/dev/console 2>&1 [SYSTEM]/bin/mv /etc_ro/Wireless/RT2860AP/SingleSKU.dat.MT7620 /etc/Wireless/RT2860AP/SingleSKU.dat [SYSTEM]/bin/mv /etc_ro/Wireless/iNIC/SingleSKU.dat.MT7610E /etc_ro/Wireless/iNIC/SingleSKU.dat CHIP: 7603 - current MAC: XX:XX:XX:XX:XX:XX Assign MAC: XX:XX:XX:XX:XX:XX no update! CHIP: 7662 - current MAC: XX:XX:XX:XX:XX:XX Assign MAC: XX:XX:XX:XX:XX:XX no update! [SYSTEM]/sbin/iwpriv rai0 set RadioOn=1 Interface doesn't accept private ioctl... set (8BE2): Network is down [SYSTEM]echo 1 > /tmp/wifi_mac_setNOTIFY X_BCN DESC a7f94000 size = 320 [3RX[0] DESC a7f96000 size = 2048 2m[SYSTEM]/sbiRX[1] DESC a7f97000 size = 2048 n/ifconfig ra0 up cfg_mode=9 cfg_mode=9 wmode_band_equal(): Band Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 20140814CmdAddressLenReq:(ret = 0) CmdFwStartReq: override = 1, address = 1048576 CmdStartDLRsp: WiFI FW Download Success AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC) CmdPsRetrieveRsp Disable FW PS Supportstatus:1 !!!!! RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 efuse_probe: efuse = 10000002 RtmpEepromGetDefault::e2p_dafault=1 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 NVM is FLASH mode 1. Phy Mode = 14 Country Region from e2p = ffff tssi_1_target_pwr_g_band = 35 2. Phy Mode = 14 3. Phy Mode = 14 NICInitPwrPinCfg(13): Not support for HIF_MT yet! NICInitializeAsic(586): Not support rtmp_mac_sys_reset () for HIF_MT yet! mt_mac_init()--> mt7603_init_mac_cr()--> AsicSetMacMaxLen(1561): Set the Max RxPktLen=1024! <--mt_mac_init() WTBL Segment 1 info: MemBaseAddr/FID:0x28000/0 EntrySize/Cnt:32/128 WTBL Segment 2 info: MemBaseAddr/FID:0x40000/0 EntrySize/Cnt:64/128 WTBL Segment 3 info: MemBaseAddr/FID:0x42000/64 EntrySize/Cnt:64/128 WTBL Segment 4 info: MemBaseAddr/FID:0x44000/128 EntrySize/Cnt:32/128 AntCfgInit(2362): Not support for HIF_MT yet! AsicSendCommandToMcu(3410): Not support for HIF_MT yet! AsicSendCommandToMcu(3410): Not support for HIF_MT yet! AsicSendCommandToMcu(3410): Not support for HIF_MT yet! AsicSendCommandToMcu(3410): Not support for HIF_MT yet! RTMPSetPhyMode(): channel out of range, use first ch=0 MCS Set = ff ff 00 00 01 AsicSetChBusyStat(877): Not support for HIF_MT yet! CmdChannelSwitch: control_chl = 1, central_chl = 1, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#1(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 2, central_chl = 2, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#2(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 3, central_chl = 3, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 4, central_chl = 4, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 5, central_chl = 5, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#5(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 6, central_chl = 6, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#6(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 7, central_chl = 7, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 8, central_chl = 8, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#8(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 9, central_chl = 9, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#9(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 10, central_chl = 10, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#10(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 11, central_chl = 11, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#11(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 12, central_chl = 12, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#12(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 13, central_chl = 13, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#13(2T2R), BBP_BW=0 CmdChannelSwitch: control_chl = 1, central_chl = 1, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#1(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 2, central_chl = 2, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#2(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 3, central_chl = 3, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 4, central_chl = 4, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#4(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 5, central_chl = 5, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#5(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 6, central_chl = 6, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#6(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 7, central_chl = 7, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#7(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l CmdChannelSwitch: control_chl = 8, central_chl = 8, BW = 0, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#8(2T2R), BBP_BW=0 SYNC - BBP R4 to 20MHz.l [PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 [PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0 [PMF]ap_pmf_init:: apidx=2, MFPC=0, MFPR=0, SHA256=0 [PMF]ap_pmf_init:: apidx=3, MFPC=0, MFPR=0, SHA256=0 AsicSetRalinkBurstMode(3724): Not support for HIF_MT yet! RTMPSetPiggyBack(797): Not support for HIF_MT yet! CmdChannelSwitch: control_chl = 1, central_chl = 3, BW = 1, TXStream = 2, RXStream = 2 mt7603_switch_channel(): Switch to Ch#3(2T2R), BBP_BW=1 AsicSetTxPreamble(3710): Not support for HIF_MT yet! AsicAddSharedKeyEntry(1725): Not support for HIF_MT yet! AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0 Main bssid = XX:XX:XX:XX:XX:XX <==== rt28xx_init, Status=0 NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY [SYSTEM]/sbin/brctl addevice ra0 entered promiscuous mode dibr0: port 2(ra0) entering learning state f br0: port 2(ra0) entering learning state br0 ra0 [SYSTEM]/bin/led_app on 40 [SYSTEM]/sbin/ifconfig rNOTIFY aibuild time = 02 0u1p4[400m8 60640a rom patch for E3 IC platform = ALPS hw/sw version = ŠŠ patch version = FW Version:0.0.00 Build:1 Build Time:201409051439____ fw for E3 IC RX[0] DESC a6694000 size = 4 GiB RX[1] DESC a6695000 size = 4 GiB E2pAccessMode=2 cfg_mode=8 cfg_mode=8 wmode_band_equal(): Band Not Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 flush result = ffffff check pse fid Q7:set_get_fid, q_idx:7 empty!! Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 17 get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (171) br0: port 2(ra0) entering forwarding state get_chl_grp:illegal channel (173) get_chl_grp:illegal channel (173) Country Region from e2p = ffff mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=1, temp_tx_alc_enable=1 mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=13, low_temp_slope=9 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_get_external_lna_gain::LNA type=0x1, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c 2. Phy Mode = 17 3. Phy Mode = 17 andes_pci_fw_init 0x1300 = 00073200 AntCfgInit: primary/secondary ant 0/1 andes_load_cr:cr_type(2) ChipStructAssign(): MT76x2 hook ! RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff 00 00 01 mt76x2_single_sku::DefaultTargetPwr = 0x26, delta_power = 0xfffffffe mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x26, ch_pwr_adj = 0xfffffffa(-6), 0x13B4: 0x1b0f043a mt76x2_single_sku::DefaultTargetPwr = 0x26, delta_power = 0xfffffffe mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x26, ch_pwr_adj = 0xfffffffa(-6), 0x13B4: 0x1b0f043a mt76x2_single_sku::DefaultTargetPwr = 0x26, delta_power = 0xfffffffe mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x26, ch_pwr_adj = 0xfffffffa(-6), 0x13B4: 0x1b0f043a br0: port 1(eth2) entering forwarding state mt76x2_single_sku::DefaultTargetPwr = 0x26, delta_power = 0xfffffffe mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x26, ch_pwr_adj = 0xfffffffa(-6), 0x13B4: 0x1b0f043a mt76x2_bbp_adjust():rf_bw=1, ext_ch=3, PrimCh=40, HT-CentCh=38, VHT-CentCh=0 mt76x2_single_sku::DefaultTargetPwr = 0x26, delta_power = 0xfffffffe mt76x2_single_sku::sku_base_pwr = 0x20, DefaultTargetPwr = 0x26, ch_pwr_adj = 0xfffffffa(-6), 0x13B4: 0x1b0f043a APStartUp(): AP Set CentralFreq at 38(Prim=40, HT-CentCh=38, VHT-CentCh=0, BBP_BW=1) mt76x2_calibration(channel = 38) Main bssid = XX:XX:XX:XX:XX:XX mt76x2_reinit_agc_gain:original agc_vga0 = 0x48, agc_vga1 = 0x48 mt76x2_reinit_agc_gain:updated agc_vga0 = 0x48, agc_vga1 = 0x48 mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33 mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33 original vga value(chain0) = 48 original vga value(chain1) = 48 <==== rt28xx_init, Status=0 NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY NOTIFY RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! NOTIFY [SYSTEM]/sbin/brctl device rai0 entered promiscuous mode addbr0: port 3(rai0) entering learning state ibr0: port 3(rai0) entering learning state f br0 rai0 [SYSTEM]/bin/led_app on 40 [libscm_wl.c::GenerateUUID():121] GUI ASCII string: 38833092-3092-1883-b1b5-a42b8c58fa38 [libscm_wl.c::GenerateUUID():122] GUI HEX string: 3883309230921883b1b5a42b8c58fa38 [SYSTEM]/usr/bin/killall miniupnpd_wsc killall: miniupnpd_wsc: no process killed [SYSTEM]/sbin/chmod +x /var/ralink_ap_start.sh [SYSTEM]/bin/sh -x /var/ralink_ap_start.sh + iwpriv ra0 set WscConfMode=0 + iwpriv rai0 set WscConfMode=0 + iwpriv ra0 set WscSetupLock=0 + iwpriv rai0 set WscSetupLock=0 + iwpriv ra0 set WscMaxPinAttack=3 + iwpriv rai0 set WscMaxPinAttack=3 + route add -host 239.255.255.250 dev br0 + iwpriv ra0 set WscConfMode=7 + iwpriv rai0 set WscConfMode=7 + miniupnpd_wsc -m 1 -I ra0 -P /var/Can't find DB for id==42 run/miniupnpd.ra0 -i eth3 -a 192.168.1.1 -n 7777 -u 38833092-3092-1883-b1b5-a42b8c58fa38 Unknown option: -I Unknown option: ra0 Jan 1 00:00:26 miniupnpd[318]: WPS listening on port 7777 [SYSTEM]/bin/cp /proc/uptime /tmp/wlan_uptiRTMPIoctlMAC():wrq->u.data.length=9, pointer(7fe88000)=60200618! meRTMPIoctlMAC():after trim space, ptr len=8, pointer(86115000)=60200618! [SYSTEM]/bin/led_app on 42 TMPIoctlMAC():wrq->u.data.length=18, pointer(7f9a36e0)=60200618=D7083F0F! [3RTMPIoctlMAC():after trim space, ptr len=17, pointer(85daf000)=60200618=D7083F0F! 2m[SYSTEM]/usr/sbin/led_app on 45 [wifi_mtk/wifi.c::start_wireless():1615] DISABLE EDCCA for 2G and 5G [SYSTEM]/usr/sbin/iwpriv rai0 mac 1340 rai0 mac: [0x1340]:04101b3f [wifi_mtk/wifi.c::start_wireless():1639] org:0x4101b3f. (04101b3f )[wifi_mtk/wifi.c::start_wireless():1641] now:0x4001b3f [SYSTEM]/usr/sbin/iwpriv rai0 mac 1340=4001b3f rai0 mac: [0x1340]:04001b3f [SYSTEM]/usr/sbin/iwpriv rai0 mac 1340 rai0 mac: [0x1340]:04001b3f [SYSTEM]/usr/sbin/iwpriv ra0 mac 60200618 ra0 mac:[0x10618]:d7e87d10 [SYSTEM]/usr/sbin/iwpriv ra0 mac 60200618=D7083F0F ra0 mac:[0x10618]:d7083f0f unlink running file </var/run/rc.wlan.run> [rc debug]/usr/sbin/rc printk start ap_name=printk action=start [rc.c::rc_action():803] rc_action before add printk - start rc action <printk @ start> before file_lock. rc action <printk @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.printk.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add printk - start [rc.c::rc_start():706] Calling Start function of printk [SYSTEM]/bin/echo 1 4 1 7 > /proc/sys/kernel/printk unlink running file </var/run/rc.printk.run> [rc debug]/usr/sbin/rc timezone start ap_name=timezone action=start [rc.c::rc_action():803] rc_action before add timezone - start rc action <timezone @ start> before file_lock. rc action <timezone @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.timezone.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add timezone - start [rc.c::rc_start():706] Calling Start function of timezone [SYSTEM]/bin/echo GMT+0 > /etc/TZ unlink running file </var/run/rc.timezone.run> [rc debug]/usr/sbin/rc syslogd start ap_name=syslogd action=start [rc.c::rc_action():803] rc_action before add syslogd - start rc action <syslogd @ start> before file_lock. rc action <syslogd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add syslogd - start [rc.c::rc_start():706] Calling Start function of syslogd [SYSTEM]/sbin/syslogd -f /etc/syslog.conf unlink running file </var/run/rc.syslogd.run> [rc debug]/usr/sbin/rc httpd start ap_name=httpd action=start [rc.c::rc_action():803] rc_action before add httpd - start rc action <httpd @ start> before file_lock. rc action <httpd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.httpd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add httpd - start [rc.c::rc_start():706] Calling Start function of httpd [sc_language.c::create_language_file():426] Create link files for <French> [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock4 to ENU [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock5 to DEU [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock6 to FRA [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock7 to NLD [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock8 to SVE [sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock9 to RUS [sc_language.c::create_language_file():449] Checking MTD </dev/mtdblock6> according to its id <FRA> [sc_language.c::decompress_language():175] Try to decompress MTD </dev/mtdblock6> [SYSTEM]/bin/cat /www.eng/block.htm | /bin/sed "s|@model_name#|WNDR3700v5|g" > /etc/block.htm rmmod: ipt_REJECT: No such file or directory [rc debug]/bin/rc firewall restart ap_name=firewall action=restart [rc.c::rc_action():803] rc_action before add firewall - restart rc action <firewall @ restart> before file_lock. rc action <firewall @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add firewall - restart unlink running file </var/run/rc.firewall.run> [rc.c::rc_action():803] rc_action before add firewall - restart rc action <firewall @ restart> before file_lock. rc action <firewall @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add firewall - restart [rc.c::rc_stop():745] Calling Stop function of firewall [SYSTEM]echo 0 > /proc/sys/net/ipv4/ip_forward [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0/forwarding sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory [SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0-va0/forwarding sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory [rc.c::rc_start():706] Calling Start function of firewall [SYSTEM]/usr/bin/killall -14 access_logd [SYSTEM]/usr/sbin/rc syslogd create;/usr/bin/killall -SIGUSR2 syslogd & [rc debug]/usr/sbin/rc syslogd create ap_name=syslogd action=create [rc.c::rc_action():803] rc_action before add syslogd - create rc action <syslogd @ create> before file_lock. rc action <syslogd @ create lock = 4> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run rc action < unlock = 4> after file_lock. [rc.c::rc_action():811] rc_action after add syslogd - create [rc.c::rc_create():787] Calling Create function of syslogd unlink running file </var/run/rc.syslogd.run> [SYSTEM]/bin/echo switch=on > /proc/net/spi_enable [SYSTEM]/bin/echo clear > /proc/net/firewall_block [SYSTEM]/bin/echo clear > /proc/net/clamp_total_session_for_one_src [SYSTEM]/bin/echo clear > /proc/net/psd_udp_tcp_vanilla_port_scan [SYSTEM]/bin/echo clear > /proc/net/echo_chargen_config [SYSTEM]/bin/echo wan_if=eth3 > /proc/net/spi_enable [SYSTEM]/bin/echo spi=enable > /proc/net/spi_enable fw_pt [SYSTEM]/usr/sbin/killall -9 usb_httpd killall: usb_httpd: no process killed [SYSTEM]/bin/echo "enable_ipmac=0" > /proc/arp_protect_enable [flash.c::sc_get_region():327] Original Region Data: 00, 00, 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.1.1 [flash.c::sc_get_region():327] Original Region Data: 00, 00, 00, 02 [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab [SYSTEM]/bin/echo GMT+0 > /etc/TZ [SYSTEM]echo 1 > /proc/net/ipt_condition/schedule sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory unlink running file </var/run/rc.firewall.run> [SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR WNDR3700v5" -c '**.cgi' -t 300& unlink running file </var/run/rc.httpd.run> [rc debug]/usr/sbin/rc remote_httpd start ap_name=remote_httpd action=start [rc.c::rc_action():803] rc_action before add remote_httpd - start rc action <remote_httpd @ start> before file_lock. rc action <remote_httpd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.remote_httpd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add remote_httpd - start [rc.c::rc_start():706] Calling Start function of remote_httpd unlink running file </var/run/rc.remote_httpd.run> [rc debug]/usr/sbin/rc dhcpd start ap_name=dhcpd action=start [rc.c::rc_action():803] rc_action before add dhcpd - start rc action <dhcpd @ start> before file_lock. rc action <dhcpd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dhcpd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add dhcpd - start [rc.c::rc_start():706] Calling Start function of dhcpd killall: udhcpd: no process killed unlink running file </var/run/rc.dhcpd.run> [rc debug]/usr/sbin/rc ntp start ap_name=ntp action=start [rc.c::rc_action():803] rc_action before add ntp - start rc action <ntp @ start> before file_lock. rc action <ntp @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ntp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add ntp - start [rc.c::rc_start():706] Calling Start function of ntp [SYSTEM]/usr/sbin/netgear_ntp -z GMT+0& [dhcpd.c::udhcpd():116] udhcp server (v0.9.7) started [dhcpd.c::udhcpd():170] interface: br0, start : 201a8c0 end : fe01a8c0 unlink running file </var/run/rc.ntp.run> [rc debug]/usr/sbin/rc route start ap_name=route action=start [rc.c::rc_action():803] rc_action before add route - start rc action <route @ start> before file_lock. rc action <route @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add route - start [rc.c::rc_start():706] Calling Start function of route unlink running file </var/run/rc.route.run> [rc debug]/usr/sbin/rc ripd start ap_name=ripd action=start [rc.c::rc_action():803] rc_action before add ripd - start rc action <ripd @ start> before file_lock. rc action <ripd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ripd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add ripd - start [rc.c::rc_start():706] Calling Start function of ripd unlink running file </var/run/rc.ripd.run> [rc debug]/usr/sbin/rc dnrd start ap_name=dnrd action=start [rc.c::rc_action():803] rc_action before add dnrd - start rc action <dnrd @ start> before file_lock. rc action <dnrd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add dnrd - start [rc.c::rc_start():706] Calling Start function of dnrd [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.1.1:80 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.1.1 [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.1.1 iptables: No chain/target/match by that name. [SYSTEM]killall -9 dnrd killall: dnrd: no process killed [SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.1.1 iptables: No chain/target/match by that name. [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.1.1 [SYSTEM]iptables -t nat -I PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.1.1:80 [SYSTEM]dnrd -a 192.168.1.1 -m hosts -c off -g routerlogin.com & unlink running file </var/run/rc.dnrd.run> [rc debug]/usr/sbin/rc potcounter start ap_name=potcounter action=start [rc.c::rc_action():803] rc_action before add potcounter - start rc action <potcounter @ start> before file_lock. rc action <potcounter @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.potcounter.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add potcounter - start [rc.c::rc_start():706] Calling Start function of potcounter unlink running file </var/run/rc.potcounter.run> [rc debug]/usr/sbin/rc lltd start ap_name=lltd action=start [rc.c::rc_action():803] rc_action before add lltd - start rc action <lltd @ start> before file_lock. rc action <lltd @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.lltd.run Notice: caching turned off Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off. rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add lltd - start [rc.c::rc_start():706] Calling Start function of lltd unlink running file </var/run/rc.lltd.run> [rc debug]/usr/sbin/rc usb_init start ap_name=usb_init action=start [rc.c::rc_action():803] rc_action before add usb_init - start rc action <usb_init @ start> before file_lock. rc action <usb_init @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_init.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add usb_init - start [rc.c::rc_start():706] Calling Start function of usb_init [SYSTEM]/etc/mtk/mt7621_smp.sh wifi [SYSTEM]/bin/rm /etc/samba/secrets.tdb rm: cannot remove '/etc/samba/secrets.tdb': No such file or directory [SYSTEM]/usr/bin/killall -9 smbd >/dev/null 2>&1 [SYSTEM]/usr/bin/killall -9 nmbd >/dev/null 2>&1 [SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1 [SYSTEM]/usr/sbin/killall -9 hd-idle killall: hd-idle: no process killed [SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1 [SYSTEM]/usr/sbin/killall -9 hd-idle killall: hd-idle: no process killed unlink running file </var/run/rc.usb_init.run> [rc debug]/usr/sbin/rc debug_mode start ap_name=debug_mode action=start [rc.c::rc_action():803] rc_action before add debug_mode - start rc action <debug_mode @ start> before file_lock. rc action <debug_mode @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.debug_mode.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add debug_mode - start [rc.c::rc_start():706] Calling Start function of debug_mode unlink running file </var/run/rc.debug_mode.run> [rc debug]/usr/sbin/rc wifi_isolation start ap_name=wifi_isolation action=start [rc.c::rc_action():803] rc_action before add wifi_isolation - start rc action <wifi_isolation @ start> before file_lock. rc action <wifi_isolation @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.wifi_isolation.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add wifi_isolation - start [rc.c::rc_start():706] Calling Start function of wifi_isolation [SYSTEM]/bin/echo "lan_ip=192.168.1.1" > /proc/wifi_isolation sh: cannot create /proc/wifi_isolation: nonexistent directory [SYSTEM]/bin/echo "lan_netmask=255.255.255.0" > /proc/wifi_isolation sh: cannot create /proc/wifi_isolation: nonexistent directory unlink running file </var/run/rc.wifi_isolation.run> [rc debug]/usr/sbin/rc mediaserver start ap_name=mediaserver action=start [rc.c::rc_action():803] rc_action before add mediaserver - start rc action <mediaserver @ start> before file_lock. rc action <mediaserver @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.mediaserver.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add mediaserver - start [rc.c::rc_start():706] Calling Start function of mediaserver #### media server is disable unlink running file </var/run/rc.mediaserver.run> [rc debug]/usr/sbin/rc bridge_iptv_port start ap_name=bridge_iptv_port action=start [rc.c::rc_action():803] rc_action before add bridge_iptv_port - start rc action <bridge_iptv_port @ start> before file_lock. rc action <bridge_iptv_port @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.bridge_iptv_port.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add bridge_iptv_port - start unlink running file </var/run/rc.bridge_iptv_port.run> [rc.c::rc_action():803] rc_action before add bridge_iptv_port - start rc action <bridge_iptv_port @ start> before file_lock. rc action <bridge_iptv_port @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.bridge_iptv_port.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add bridge_iptv_port - start unlink running file </var/run/rc.bridge_iptv_port.run> can't find this application [rc.c::rc_action():803] rc_action before add bridge_iptv_port - start rc action <bridge_iptv_port @ start> before file_lock. rc action <bridge_iptv_port @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.bridge_iptv_port.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add bridge_iptv_port - start unlink running file </var/run/rc.bridge_iptv_port.run> can't find this application [rc debug]/usr/sbin/rc vlan start ap_name=vlan action=start [rc.c::rc_action():803] rc_action before add vlan - start rc action <vlan @ start> before file_lock. rc action <vlan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.vlan.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add vlan - start unlink running file </var/run/rc.vlan.run> [rc.c::rc_action():803] rc_action before add vlan - start rc action <vlan @ start> before file_lock. rc action <vlan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.vlan.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add vlan - start unlink running file </var/run/rc.vlan.run> can't find this application [rc.c::rc_action():803] rc_action before add vlan - start rc action <vlan @ start> before file_lock. rc action <vlan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.vlan.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add vlan - start unlink running file </var/run/rc.vlan.run> can't find this application [rc debug]/usr/sbin/rc dbus start ap_name=dbus action=start [rc.c::rc_action():803] rc_action before add dbus - start rc action <dbus @ start> before file_lock. rc action <dbus @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dbus.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add dbus - start unlink running file </var/run/rc.dbus.run> [rc.c::rc_action():803] rc_action before add dbus - start rc action <dbus @ start> before file_lock. rc action <dbus @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dbus.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add dbus - start unlink running file </var/run/rc.dbus.run> can't find this application [rc.c::rc_action():803] rc_action before add dbus - start rc action <dbus @ start> before file_lock. rc action <dbus @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.dbus.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add dbus - start unlink running file </var/run/rc.dbus.run> can't find this application =============rc finish run smp wifi run smp wifi done PID USER VSZ STAT COMMAND 1 root 1496 S init 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 4 root 0 SW [kworker/0:0] 5 root 0 SW [kworker/u:0] 6 root 0 SW [migration/0] 7 root 0 SW [migration/1] 8 root 0 SW [kworker/1:0] 9 root 0 SW [ksoftirqd/1] 10 root 0 SW< [khelper] 11 root 0 SW [kworker/1:1] 12 root 0 SW [sync_supers] 13 root 0 SW [bdi-default] 14 root 0 SW< [kblockd] 15 root 0 SW [khubd] 16 root 0 SW [kswapd0] 17 root 0 SW [fsnotify_mark] 18 root 0 SW< [xfs_mru_cache] 19 root 0 SW< [xfslogd] 20 root 0 SW< [xfsdatad] 21 root 0 SW< [xfsconvertd] 22 root 0 SW< [crypto] 29 root 0 SW [mtdblock0] 30 root 0 SW [mtdblock1] 31 root 0 SW [mtdblock2] 32 root 0 SW [mtdblock3] 33 root 0 SW [mtdblock4] 34 root 0 SW [mtdblock5] 35 root 0 SW [mtdblock6] 36 root 0 SW [mtdblock7] 37 root 0 SW [mtdblock8] 38 root 0 SW [mtdblock9] 39 root 0 SW [mtdblock10] 40 root 0 SW [mtdblock11] 41 root 0 SW [mtdblock12] 42 root 0 SW [mtdblock13] 43 root 0 SW [mtdblock14] 44 root 0 SW [mtdblock15] 45 root 0 SW [mtdblock16] 46 root 0 SW [mtdblock17] 47 root 0 SW [mtdblock18] 48 root 0 SW [mtdblock19] 49 root 0 SW [kworker/u:1] 56 root 0 SW [kworker/0:1] 58 root 1496 S /bin/sh /usr/etc/rcS 146 root 1032 S /sbin/klogd 148 root 920 S /usr/sbin/cmd_agent_ap 218 root 1024 S /sbin/access_logd 231 root 1136 S /sbin/access_devinfo 255 root 1212 S /usr/sbin/scfgmgr 286 root 0 SW [RtmpCmdQTask] 287 root 0 SW [RtmpWscTask] 288 root 0 SW [RtmpMlmeTask] 295 root 0 SW [RtmpCmdQTask] 296 root 0 SW [RtmpWscTask] 297 root 0 SW [RtmpMlmeTask] 318 root 1084 S miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 - 360 root 1092 S /sbin/syslogd -f /etc/syslog.conf 871 root 1048 S /usr/sbin/udhcpd /etc/udhcpd.conf 876 root 940 S /usr/sbin/netgear_ntp -z GMT+0 878 root 1444 S /usr/sbin/mini_httpd -d /www -r NETGEAR WNDR3700v5 -c 1523 root 928 S /usr/sbin/potcounter 1527 root 1432 S dnrd -a 192.168.1.1 -m hosts -c off -g routerlogin.co 1531 root 1144 S /usr/bin/lld2 br0 1573 root 940 S telnetenabled 192.168.1.1 A42B8C58FA38 admin password 1623 root 1496 R /bin/ps [rc debug]/usr/sbin/rc upnp start ap_name=upnp action=start [rc.c::rc_action():803] rc_action before add upnp - start rc action <upnp @ start> before file_lock. rc action <upnp @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add upnp - start unlink running file </var/run/rc.upnp.run> [rc.c::rc_action():803] rc_action before add upnp - start rc action <upnp @ start> before file_lock. rc action <upnp @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add upnp - start unlink running file </var/run/rc.upnp.run> can't find this application [rc.c::rc_action():803] rc_action before add upnp - start rc action <upnp @ start> before file_lock. rc action <upnp @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add upnp - start [rc.c::rc_start():706] Calling Start function of upnp [SYSTEM]route add -net 239.0.0.0 netmask 255.0.0.0 br0 [SYSTEM]/usr/sbin/miniupnpd -i eth3 -a 192.168.1.1 -p 56688 -U -t 1800 -T 4 -u 824ff22b-8c7d-41c5-a131-a42b8c58fa38 unlink running file </var/run/rc.upnp.run> route: SIOCADDRT: File exists [rc debug]/usr/sbin/rc schedule restart [rc.c::rc_action():803] rc_action before add schedule - restart rc action <schedule @ restart> before file_lock. rc action <schedule @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.schedule.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add schedule - restart unlink running file </var/run/rc.schedule.run> [rc.c::rc_action():803] rc_action before add schedule - restart rc action <schedule @ restart> before file_lock. rc action <schedule @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.schedule.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add schedule - restart [rc.c::rc_start():706] Calling Start function of schedule /usr/etc/rcS: line 282: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory /usr/etc/rcS: line 283: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory /usr/etc/rcS: line 287: cannot create [flash.c::sc_get_region():327] Original Region Data: 00, 00, 00, 02 /proc/sys/net/ipv4/conf/eth1/rp_filter: nonexistent directory [SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab [SYSTEM]/bin/echo GMT+0 > /etc/TZ [SYSTEM]echo 1 > /proc/net/ipt_condition/schedule unlink running file </var/run/rc.schedule.run> [rc debug][rc debug]usr/sbin/rc /usr/sbin/rc reset_lan wan start start ap_name=reset_lan action=start [rc.c::rc_action():803] rc_action before add reset_lan - start rc action <reset_lan @ start> before file_lock. rc action <reset_lan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run [SYSTEM]/usr/sbin/brctl delif br0 eth3 rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add reset_lan - start unlink running file </var/run/rc.reset_lan.run> [rc.c::rc_action():803] rc_action before add reset_lan - start rc action <reset_lan @ start> before file_lock. rc action <reset_lan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add reset_lan - start unlink running file </var/run/rc.reset_lan.run> can't find this application [rc.c::rc_action():803] rc_action before add reset_lan - start rc action <reset_lan @ start> before file_lock. rc action <reset_lan @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run device eth3 is not a slave of br0 [SYSTEM]/usr/bin/killall netgear_ntp rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add reset_lan - start [rc.c::rc_start():706] Calling Start function of reset_lan down port 0 Set: phy[0].reg[0] = 1840 down port 1 [SYSTEM]/usr/bin/killall -SIGUSR2 miniupnpd killall: ripd: no process killed Set: phy[1].reg[0] = 1840 killall: zebra: no process killed down port 2 Set: phy[2].reg[0] = 1840 down port 3 Set: phy[3].reg[0] = 1840 killall: ripd: no process killed killall: zebra: no process killed [SYSTEM]/bin/echo 0 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]/usr/sbin/iptables -t nat -F POSTROUTING [SYSTEM]/usr/sbin/iptables -t nat -A POSTROUTING -o eth3 -j MASQUERADE [SYSTEM]/bin/echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding [SYSTEM]/usr/sbin/iptables -D PRE_BASIC -t nat -i eth3 -d ! (null) -j DROP sh: syntax error: "(" unexpected [SYSTEM]/bin/echo "#!/bin/sh" > /etc/ppp/ip-down [SYSTEM]/usr/bin/killall pppd killall: pppd: no process killed [SYSTEM]/usr/bin/killall openl2tpd killall: openl2tpd: no process killed [SYSTEM]/usr/bin/killall udhcpc killall: udhcpc: no process killed [SYSTEM]/usr/bin/killall pppoe-relay killall: pppoe-relay: no process killed [SYSTEM]/sbin/ifconfig eth3 0.0.0.0 >/dev/null 2>&1 [SYSTEM]/sbin/ifconfig eth3 down [SYSTEM]/sbin/ifconfig eth3 hw ether XX:XX:XX:XX:XX:XX [SYSTEM]/sbin/ifconfig eth3 up [SYSTEM]/sbin/ifconfig eth3 mtu 1500 [wan/wan.c::start_wan():1372] wan_mode is <dhcpc> [SYSTEM]/bin/echo 3 > /proc/sys/vm/drop_caches; /bin/insmod /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko [SYSTEM]/usr/sbin/udhcpc -i eth3 -s /etc/udhcpc.script -H "WNDR3700v5" & [wan/wan.c::start_wan():1456] ipv6 restart, v4 mode dhcpc v6 mode disable [SYSTEM]/usr/sbin/rc ipv6 restart [dhcpc.c::udhcpc():443] udhcp client (v0.9.7) started [clientpacket.c::send_discover():175] Sending discover... [rc debug]/usr/sbin/rc ipv6 restart ap_name=ipv6 action=restart [rc.c::rc_action():803] rc_action before add ipv6 - restart rc action <ipv6 @ restart> before file_lock. rc action <ipv6 @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add ipv6 - restart unlink running file </var/run/rc.ipv6.run> [rc.c::rc_action():803] rc_action before add ipv6 - restart rc action <ipv6 @ restart> before file_lock. rc action <ipv6 @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add ipv6 - restart unlink running file </var/run/rc.ipv6.run> can't find this application [rc.c::rc_action():803] rc_action before add ipv6 - restart rc action <ipv6 @ restart> before file_lock. rc action <ipv6 @ restart lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.ipv6.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add ipv6 - restart [rc.c::rc_stop():745] Calling Stop function of ipv6 [SYSTEM]/bin/echo 0 > /proc/sys/net/ipv6/conf/all/forwarding [SYSTEM]/usr/bin/killall dhcp6c killall: dhcp6c: no process killed [SYSTEM]/bin/killall pppd_ip6 killall: pppd_ip6: no process killed [SYSTEM]/usr/bin/killall radvd killall: radvd: no process killed [SYSTEM]/usr/bin/killall -9 dhcp6s killall: dhcp6s: no process killed [SYSTEM]/bin/killall -9 totd killall: totd: no process killed [SYSTEM]ip6tables -t filter -F up port 0 [SYSTEM]ip6tables -t mangle -F [SYSTEM]ip6tables -t raw -F Set: phy[0].reg[0] = 1240 [SYSTEM]ip6tables -t filter -X up port 1 [SYSTEM]ip6tables -t mangle -X Set: phy[1].reg[0] = 1240 [SYSTEM]ip6tables -t raw -X up port 2 [SYSTEM]ip6tables -t filter -P INPUT ACCEPT Set: phy[2].reg[0] = 1240 up port 3 [SYSTEM]ip6tables -t filter -P FORWARD ACCEPT Set: phy[3].reg[0] = 1240 unlink running file </var/run/rc.reset_lan.run> [SYSTEM]ip6tables -C /tmp/rules6 ip6tables v1.4.10: option `-C' requires an argument Try `ip6tables -h' or 'ip6tables --help' for more information. [SYSTEM]killall mld killall: mld: no process killed [SYSTEM]/sbin/ip -6 route flush dev tun6to4 Cannot find device "tun6to4" [SYSTEM]/sbin/ip link set dev tun6to4 down SIOCGIFFLAGS: No such device [SYSTEM]/sbin/ip tunnel del tun6to4 ioctl: No such device [SYSTEM]/sbin/rmmod ipv6_br.ko rmmod: ipv6_br.ko: No such file or directory [SYSTEM]/usr/bin/killall dhcp6c killall: dhcp6c: no process killed [SYSTEM]/usr/bin/killall ip6_autod killall: ip6_autod: no process killed [SYSTEM]/bin/rm -f /var/ip6prefix* [ipv6/ipv6.c::stop_ipv6():72] stop ip6 wan mode: (-1) [SYSTEM]/bin/ip -6 route del RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del RTNETLINK answers: No such file or directory [rc.c::rc_start():706] Calling Start function of ipv6 [ipv6/common.c::ip6_config_dump():146] lan_ifname = <br0> [ipv6/common.c::ip6_config_dump():147] wan_ifname = <eth3> [ipv6/common.c::ip6_config_dump():148] wan_l2_ifname = <eth3> [ipv6/common.c::ip6_config_dump():149] wan_ppp_ifname = <ppp6> [ipv6/common.c::ip6_config_dump():150] wan_mode = 0 [ipv6/common.c::ip6_config_dump():151] lan_mode = 2 [ipv6/common.c::ip6_config_dump():152] dhcp_account = <> [ipv6/common.c::ip6_config_dump():153] dhcp_domain = <> [ipv6/common.c::ip6_config_dump():154] pppoe_username = <> [ipv6/common.c::ip6_config_dump():155] pppoe_passwd = <> [ipv6/common.c::ip6_config_dump():156] pppoe_service = <> [ipv6/common.c::ip6_config_dump():157] custom_relay_router = 0 [ipv6/common.c::ip6_config_dump():158] relay_router = <> [ipv6/common.c::ip6_config_dump():159] fixed_wan_ipaddr = <> [ipv6/common.c::ip6_config_dump():160] fixed_gw_ipaddr = <> [ipv6/common.c::ip6_config_dump():161] fixed_wan_plen = 0 [ipv6/common.c::ip6_config_dump():162] fixed_lan_ipaddr = <> [ipv6/common.c::ip6_config_dump():163] fixed_lan_plen = 0 [ipv6/common.c::ip6_config_dump():164] fixed_dns1 = <> [ipv6/common.c::ip6_config_dump():165] fixed_dns2 = <> [ipv6/common.c::ip6_config_dump():166] custom_ifid_enable = 0 [ipv6/common.c::ip6_config_dump():169] ifid = <0000:0000:0000:0000> [ipv6/common.c::ip6_config_dump():171] ipv6ipv4ppp_one_session = 0 [ipv6/common.c::ip6_config_dump():172] ipv6_ppp_stateless = 0 [ipv6/common.c::ip6_config_dump():173] ipv6_dhcpc_no_na = 0 [SYSTEM]/bin/echo 1 > /proc/sys/net/ipv6/conf/all/disable_ipv6 [SYSTEM]/bin/echo 2 > /proc/sys/net/ipv6/conf/all/forwarding [ipv6/ipv6.c::start_ipv6():163] ipv6 is over layer2, open rs/ra on eth3 [SYSTEM]/bin/echo 3 > /proc/sys/net/ipv6/conf/eth3/router_solicitations [SYSTEM]/bin/echo 2 > /proc/sys/net/ipv6/conf/eth3/accept_ra [ipv6/ipv6.c::start_ipv6():167] ipv6 is over layer2 interface eth3, trigger wan send out router solicitation [SYSTEM]/bin/echo trigger_rs=1 > /proc/net/trigger_rs [SYSTEM]/bin/echo wan_if=eth3 > /proc/net/trigger_rs [ipv6/ipv6.c::start_ipv6():186] ip6 is disabled. unlink running file </var/run/rc.ipv6.run> [clientpacket.c::send_discover():175] Sending discover... [clientpacket.c::send_discover():175] Sending discover... [rc debug]/usr/sbin/rc usb_printer start ap_name=usb_printer action=start [rc.c::rc_action():803] rc_action before add usb_printer - start rc action <usb_printer @ start> before file_lock. rc action <usb_printer @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_printer.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add usb_printer - start unlink running file </var/run/rc.usb_printer.run> [rc.c::rc_action():803] rc_action before add usb_printer - start rc action <usb_printer @ start> before file_lock. rc action <usb_printer @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_printer.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add usb_printer - start unlink running file </var/run/rc.usb_printer.run> can't find this application [rc.c::rc_action():803] rc_action before add usb_printer - start rc action <usb_printer @ start> before file_lock. rc action <usb_printer @ start lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_printer.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add usb_printer - start [rc.c::rc_start():706] Calling Start function of usb_printer [SYSTEM]/sbin/killall KC_BONJOUR cable_down_once killall: KC_BONJOUR: no process killed [SYSTEM]/sbin/killall KC_PRINT [rc debug]/usr/sbin/rc down_manage stop ap_name=down_manage action=stop [rc.c::rc_action():803] rc_action before add down_manage - stop rc action <down_manage @ stop> before file_lock. rc action <down_manage @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add down_manage - stop unlink running file </var/run/rc.down_manage.run> [rc.c::rc_action():803] rc_action before add down_manage - stop rc action <down_manage @ stop> before file_lock. rc action <down_manage @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add down_manage - stop unlink running file </var/run/rc.down_manage.run> can't find this application [rc.c::rc_action():803] rc_action before add down_manage - stop rc action <down_manage @ stop> before file_lock. rc action <down_manage @ stop lock = 3> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run killall: KC_PRINT: no process killed [SYSTEM]/sbin/rmmod usblp rmmod: usblp: No such file or directory [SYSTEM]/sbin/rmmod NetUSB.ko rc action < unlock = 3> after file_lock. [rc.c::rc_action():811] rc_action after add down_manage - stop unlink running file </var/run/rc.down_manage.run> can't find this application rmmod: NetUSB.ko: No such file or directory [SYSTEM]/sbin/rmmod GPL_NetUSB.ko rmmod: GPL_NetUSB.ko: No such file or directory [dhcpc.c::release_requested():161] Received SIGUSR2, state=0,sig=51 ================== interface=eth3 PATH=/bin:/sbin:/usr/sbin:/usr/bin HOME=/ route_related_options_del_file=/tmp/dhcpc_route_related_options_del ================== [SYSTEM]/sbin/insmod /lib/modules/GPL_NetUSB.ko rm: cannot remove '/tmp/wan_uptime': No such file or directory rm: cannot remove '/tmp/wan_ipaddr': No such file or directory rm: cannot remove '/tmp/dhcpc.lease': No such file or directory deleting dhcpc options releated routers /bin/sh: can't open /tmp/dhcpc_route_related_options_del [rc debug]/usr/sbin/rc route restart ap_name=route action=restart [rc.c::rc_action():803] rc_action before add route - restart rc action <route @ restart> before file_lock. rc action <route @ restart lock = 4> after file_lock. [SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run rc action < unlock = 4> after file_lock. [rc.c::rc_action():811] rc_action after add route - restart [rc.c::rc_stop():745] Calling Stop function of route [SYSTEM]/sbin/insmod /lib/modules/NetUSB.ko localID="WNDR3700v5" [rc.c::rc_start():706] Calling Start function of route unlink running file </var/run/rc.route.run> [SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/usb/class/usblp.ko [SYSTEM]/sbin/KC_BONJOUR WNDR3700v5 & [SYSTEM]/sbin/KC_PRINT WNDR3700v5 & unlink running file </var/run/rc.usb_printer.run> PID USER VSZ STAT COMMAND 1 root 1496 S init 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 4 root 0 SW [kworker/0:0] 5 root 0 SW [kworker/u:0] 6 root 0 SW [migration/0] 7 root 0 SW [migration/1] 8 root 0 SW [kworker/1:0] 9 root 0 SW [ksoftirqd/1] 10 root 0 SW< [khelper] 11 root 0 SW [kworker/1:1] 12 root 0 SW [sync_supers] 13 root 0 SW [bdi-default] 14 root 0 SW< [kblockd] 15 root 0 SW [khubd] 16 root 0 SW [kswapd0] 17 root 0 SW [fsnotify_mark] 18 root 0 SW< [xfs_mru_cache] 19 root 0 SW< [xfslogd] 20 root 0 SW< [xfsdatad] 21 root 0 SW< [xfsconvertd] 22 root 0 SW< [crypto] 29 root 0 SW [mtdblock0] 30 root 0 SW [mtdblock1] 31 root 0 SW [mtdblock2] 32 root 0 RW [mtdblock3] 33 root 0 SW [mtdblock4] 34 root 0 SW [mtdblock5] 35 root 0 SW [mtdblock6] 36 root 0 SW [mtdblock7] 37 root 0 SW [mtdblock8] 38 root 0 SW [mtdblock9] 39 root 0 SW [mtdblock10] 40 root 0 SW [mtdblock11] 41 root 0 SW [mtdblock12] 42 root 0 SW [mtdblock13] 43 root 0 SW [mtdblock14] 44 root 0 SW [mtdblock15] 45 root 0 SW [mtdblock16] 46 root 0 SW [mtdblock17] 47 root 0 SW [mtdblock18] 48 root 0 SW [mtdblock19] 49 root 0 SW [kworker/u:1] 56 root 0 SW [kworker/0:1] 58 root 1496 S /bin/sh /usr/etc/rcS 146 root 1032 S /sbin/klogd 148 root 920 S /usr/sbin/cmd_agent_ap 218 root 1024 S /sbin/access_logd 231 root 1136 S /sbin/access_devinfo 255 root 1212 S /usr/sbin/scfgmgr [Bonjour] Interface: br0 is connected [KC] WNDR3700v5 IPP v1.3 Start (Jun 26 2014 09:59:43) 286 root 0 SW [RtmpCmdQTask] 287 root 0 SW [RtmpWscTask] 288 root 0 SW [RtmpMlmeTask] 295 root 0 SW [RtmpCmdQTask] 296 root 0 SW [RtmpWscTask] 297 root 0 SW [RtmpMlmeTask] 318 root 1084 S miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 - 360 root 1092 S /sbin/syslogd -f /etc/syslog.conf 871 root 1048 S /usr/sbin/udhcpd /etc/udhcpd.conf 878 root 1444 S /usr/sbin/mini_httpd -d /www -r NETGEAR WNDR3700v5 -c 1523 root 928 S /usr/sbin/potcounter 1527 root 1432 S dnrd -a 192.168.1.1 -m hosts -c off -g routerlogin.co 1531 root 1144 S /usr/bin/lld2 br0 1573 root 940 S telnetenabled 192.168.1.1 A42B8C58FA38 admin password 1636 root 1360 S /usr/sbin/miniupnpd -i eth3 -a 192.168.1.1 -p 56688 - 1637 root 948 S /usr/sbin/crond 1638 root 1396 S /usr/sbin/multi_pb_app 90 91 92 10 50 1640 root 0 Z [crond] 1641 root 0 Z [crond] 1691 root 924 S /usr/sbin/cmd_agent 2035 root 1024 S /usr/sbin/udhcpc -i eth3 -s /etc/udhcpc.script -H WND 2782 root 1100 S usr/sbin/wan_monitor 2835 root 0 SW [ telnetDBGD ] 2836 root 0 SW [ acktelnetDBGD ] 2837 root 0 SW [checkSBusTimeou] 2839 root 0 SW [NU UDP] 2840 root 0 SW [NU TCP] 2844 root 404 S /sbin/KC_BONJOUR WNDR3700v5 2846 root 456 S /sbin/KC_PRINT WNDR3700v5 2847 root 1496 R /bin/ps 2848 root 404 S /sbin/KC_BONJOUR WNDR3700v5 2849 root 404 S /sbin/KC_BONJOUR WNDR3700v5 2854 root 456 S /sbin/KC_PRINT WNDR3700v5 2855 root 404 S /sbin/KC_BONJOUR WNDR3700v5 2856 root 456 S /sbin/KC_PRINT WNDR3700v5 2857 root 404 S /sbin/KC_BONJOUR WNDR3700v5 2858 root 456 S /sbin/KC_PRINT WNDR3700v5 /usr/etc/rcS: line 347: /usr/sbin/led_test: not found starting pid 2861, tty '/dev/ttyS1': '/bin/sh' # INFO14C9: Bind to br0 [Bonjour] MDNS_CheckName: receive packet timeout [Bonjour] default device name = WNDR3700v5 [Bonjour] Answer Name Start (192.168.1.1) [KC] WNDR3700v5 IPP v1.3 Start (Jun 26 2014 09:59:50)

Pictures

User Images

• 

  Netgear R6220 PCB