Dasan V2224G

From TechInfoDepot
Jump to navigationJump to search
Homepage
WikiDevi.wi-cat.ru
3rd Party Firmware
dd-wrt
Status Unknown
OpenWrt
Status Unknown
Tomato any flavor
Status Unknown
Platform
Brand • Model • Rev
Dasan V2224G
CPU1
Broadcom BCM53001
CPU1 Type
MIPS 74Kc
CPU1 Speed
400 MHz
Flash1 Chip
Spansion S29GL256P10TFI01
Flash1 Size
32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br />
RAM1 Size
256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />
RAM1 Chip
Samsung K4T1G084QF-BCE6 x 2
ETH chip1
Broadcom BCM53001
Switch
Broadcom BCM53001
Ethernet Port Count 24-1GbE
Ethernet connector 8P8C
Wired Standard unspecified
Auto-MDIX supported
Jumbo frame
yes
Switch Class
smart

Ethernet OUI: 00:D0:CB

Expansion IF types
none specified
Power
100-240 VAC ~ 50/60 Hz, 0.8 A
Connector type
C14
Serial Port (UART)
yes
Retail
Country of manuf China

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.

Overview

The V2224G Gigabit Ethernet Switch is a 1 RU singleboard Layer 2 switch that is optimized to provide operators with a cost-effective solution for expanding networks.

Offering 24 10/100/1000Base-T interface ports and two mounting slots for optional uplink modules, the V2224G provides the flexibility needed for a variety of network architectures.

The uplink interface supports GPON (SC/APC), EPON (SC/PC), or 1000Base-X (SFP), as a modular unit.

The V2224G can also be used as a GPON Multi Dwelling Unit (MDU) by utilizing the optional uplink modules introducing a point-to-multipoint scenario for cost-effective FTTx service delivery.

Links of Interest

Source

JTAG-Serial Info

Serial

The serial console uses a standard Cisco cable pinout.

Boot log>>
************************************************************
*                                                          *
*               Boot Loader Version 01.17.0003             *
*                   DASAN Networks Inc.                    *
*                                                          *
************************************************************
Press 's' key to go to Boot Mode:  0 
[Loading OS1 image ...]
[Image OK : os1]
   Uncompressing Kernel Image ... 
Starting kernel at 0x807618d0 ...

Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
CPU: BCM5300 rev 1 at 400 MHz
INIT: version 2.85 booting
Mounting File Systems
Install Config File System
Mounting JFFS2 Config File System
Start on Switch Initialization
Extracting configuration
Thu, 19 Aug 2021 05:09:14 +0000
Starting INET services 
INIT: Entering runlevel: 3


INIT: Start UP


SWITCH login: admin
Password: 


SWITCH> enable
SWITCH# 
U-Boot log>>
 
************************************************************
*                                                          *
*               Boot Loader Version 01.17.0003             *
*                   DASAN Networks Inc.                    *
*                                                          *
************************************************************
Press 's' key to go to Boot Mode:  0 
Boot> help
diag    - perform board diagnostics
erase_flash- erase all flash memory
flashinfo- show flash information
gateway - set GATEWAY Address
help    - print command description/usage
ip      - set IP Address
load    - download OS Image file from TFTP Server
netmask - set NETMASK Address
ping    - send ICMP ECHO_REQUEST to network host
reboot  - reboot the system using specific OS (Only Once) <os1 | os2>
set     - select default OS
sysinfo - show system information
vendor_code- show/set Vendor Specific Serial Number
version - print monitor version
Boot> version

U-Boot 2010.06-svn972 (Apr 26 2012 - 15:30:25), ( 01.17.0003 )
Boot> flashinfo
Flash Information(Bytes)
Area     OS size      Default-OS     Ready-OS      OS Version
-------------------------------------------------------------
os1       9708504          *             *         2.11 #0014
os2       9708504                                  2.11 #0014
Boot> diag
Available hardware tests:
  i2c             - I2C test
  memory          - Memory test
  cpu             - CPU test
  flash           - FLASH test
Use 'diag [<test1> [<test2> ...]]' to get more info.
Use 'diag run [<test1> [<test2> ...]]' to run tests.
Boot> diag run i2c
[test counts : 1]
POST i2c I2C: probe addr 0x68 
PASSED

Boot> diag run memory
[test counts : 1]
POST memory Writing...
0x86000000
Reading...
0x86000000
Test done!
PASSED

Boot> diag run cpu
[test counts : 1]
POST cpu Core:  MIPS74K
**Exception 32: EPC=00000000, Cause=40800008 (TLBMissRd)
                RA=877AEC6C, VAddr=00000000

        0  ($ 0) = 00000000     AT ($ 1) = A0000000
        v0 ($ 2) = 00000000     v1 ($ 3) = 00000000
        a0 ($ 4) = 877B70B8     a1 ($ 5) = 00000011
        a2 ($ 6) = 00000000     a3 ($ 7) = 00000000
        t0 ($ 8) = 87FFEE88     t1 ($ 9) = 00000000
        t2 ($10) = 87FFEDA0     t3 ($11) = 00000009
        t4 ($12) = 877CE478     t5 ($13) = 877FF050
        t6 ($14) = 877FEE00     t7 ($15) = 8773C330
        s0 ($16) = 19115300     s1 ($17) = 00000607
        s2 ($18) = 00000002     s3 ($19) = 877CF6C8
        s4 ($20) = 879FD738     s5 ($21) = 877B3000
        s6 ($22) = 00000001     s7 ($23) = 87FFEF1C
        t8 ($24) = 00000271     t9 ($25) = 00000000
        k0 ($26) = 877D8180     k1 ($27) = 8776E86C
        gp ($28) = 877D8180     sp ($29) = 87FFEE20
        fp ($30) = 87FFEF2C     ra ($31) = 877AEC6C

Linux shell can be accessed with the privileged 'quote' command that runs a system command. After running 'quote sh' we get a Linux shell:

Linux shell access>>
 
SWITCH# quote sh
*SWITCH# ls -l   
-rw-r--r--    1 admin    admin           6 Aug 19 07:15 HOSTNAME
-rw-r-----    1 admin    admin         243 Aug 19 07:15 ZebOS.conf
-rw-r--r--    1 admin    admin         155 Apr 15  2014 auth.conf
-rw-r--r--    1 admin    admin         560 Apr 15  2014 bpm_cfg.txt
-rw-r--r--    1 admin    admin           3 Apr 15  2014 cpuload.conf
-rw-r--r--    1 admin    admin       37924 Apr 15  2014 dml_input.txt
-rw-r--r--    1 admin    admin         372 Apr 15  2014 eqm.conf
-rw-r--r--    1 admin    admin         741 Apr 15  2014 fstab
-rw-r--r--    1 admin    admin          20 Aug 15 00:46 group
-rw-r--r--    1 admin    admin          43 Apr 15  2014 hosts
-rw-r-----    1 admin    admin           8 Aug 19 07:15 inetd.cmd
-rw-r-----    1 admin    admin        3353 Aug 19 07:15 inetd.conf
-rw-r-----    1 admin    admin          13 Aug 19 07:15 inetd.service
-rw-r--r--    1 admin    admin         512 Apr 15  2014 login.conf
-rw-r--r--    1 admin    admin      111892 Apr 15  2014 moduli
-rw-r--r--    1 admin    admin          46 Apr 15  2014 mtab
-rw-r--r--    1 admin    admin        1159 Apr 15  2014 nsswitch.conf
-rw-r-----    1 admin    admin          59 Aug 19 04:05 passwd
-rw-r-----    1 admin    admin           0 Aug 15 00:49 privilege.conf
-rwxr-xr-x    1 admin    admin         397 Apr 15  2014 profile
-rwxr-xr-x    1 admin    admin         364 Aug 19 07:15 proftpd.conf
-rw-r--r--    1 admin    admin        1194 Apr 15  2014 protocols
drwxr-xr-x    2 admin    admin           0 Apr 15  2014 radclient
drwxr-xr-x    2 admin    admin           0 Apr 15  2014 radius
-rw-r--r--    1 admin    admin           0 Apr 15  2014 resolv.conf
-rw-r--r--    1 admin    admin         334 Apr 15  2014 securetty
-rw-r--r--    1 admin    admin       11283 Apr 15  2014 services
-rw-r--r--    1 admin    admin         691 Aug 19 07:15 snmp-enterprise
-rw-r--r--    1 admin    admin        1213 Apr 15  2014 ssh_config
-rw-r--r--    1 admin    admin        2487 Apr 15  2014 sshd_config
-rw-r-----    1 admin    admin           5 Aug 19 07:15 sshd_start
-rw-r--r--    1 admin    admin           0 Apr 15  2014 stackd.conf
-rwxr-xr-x    1 admin    admin         774 Aug 19 07:15 startup.ifup
-rw-r--r--    1 admin    admin         156 Aug 19 07:15 startup.model
-rw-r--r--    1 admin    admin         130 Apr 15  2014 startup.net
-rw-r--r--    1 admin    admin        3147 Apr 15  2014 startup.opt
-rw-r--r--    1 admin    admin         317 Apr 15  2014 startup.post
-rw-r--r--    1 admin    admin           0 Apr 15  2014 startup.pre
-rw-r-----    1 admin    admin          66 Aug 19 07:15 syslog.conf
-rw-r-----    1 admin    admin           5 Aug 19 07:15 sysparam.conf
drwxr-xr-x    2 admin    admin           0 Apr 15  2014 tacacs
-rw-r--r--    1 admin    admin        4047 Apr 15  2014 termcap
-rw-r--r--    1 admin    admin          21 Apr 15  2014 vtysh.conf
*SWITCH# uname -a
Linux SWITCH 2.6.32 #1 Tue Apr 15 10:51:43 KST 2014 mips GNU/Linux
*SWITCH#
Processes>>
*SWITCH# ps uwwax
USER       PID %CPU %MEM   VSZ  RSS TTY      STAT START   TIME COMMAND
admin        1  0.5  0.2  2204  560 ?        Ss   07:15   0:07 init [3]  
admin        2  0.0  0.0     0    0 ?        S    07:15   0:00 [kthreadd]
admin        3  0.0  0.0     0    0 ?        S    07:15   0:00 [ksoftirqd/0]
admin        4  0.0  0.0     0    0 ?        S    07:15   0:00 [watchdog/0]
admin        5  0.0  0.0     0    0 ?        S    07:15   0:00 [events/0]
admin        6  0.0  0.0     0    0 ?        S    07:15   0:00 [khelper]
admin        9  0.0  0.0     0    0 ?        S    07:15   0:00 [async/mgr]
admin       37  0.0  0.0     0    0 ?        S    07:15   0:00 [sync_supers]
admin       39  0.0  0.0     0    0 ?        S    07:15   0:00 [bdi-default]
admin       40  0.0  0.0     0    0 ?        S    07:15   0:00 [kblockd/0]
admin       85  0.0  0.0     0    0 ?        S    07:15   0:00 [khungtaskd]
admin       86  0.0  0.0     0    0 ?        S    07:15   0:00 [kswapd0]
admin       87  0.0  0.0     0    0 ?        S    07:15   0:00 [aio/0]
admin      641  0.0  0.0     0    0 ?        S    07:15   0:00 [mtdblockd]
admin      696  0.4  0.0     0    0 ?        S<   07:15   0:05 [bcmCNTR.0]
admin      697  0.0  0.0     0    0 ?        S<   07:15   0:00 [bcmTX]
admin      698  0.0  0.0     0    0 ?        S<   07:15   0:00 [bcmXGS3AsyncTX]
admin      699  0.0  0.0     0    0 ?        SN   07:15   0:00 [bcmRX]
admin      700  0.0  0.0     0    0 ?        S<   07:15   0:00 [bcm-shell]
admin      702  0.0  0.0     0    0 ?        S<   07:15   0:00 [bcmDPC]
admin      703  0.0  0.0     0    0 ?        S    07:15   0:00 [swal_portload_t]
admin      762  0.0  0.0     0    0 ?        SN   07:15   0:00 [jffs2_gcd_mtd0]
admin      854  0.0  3.5 19616 7792 ?        S    07:15   0:00 /usr/sbin/swchd
admin      856  0.0  1.8 15008 4112 ?        S    07:15   0:00 /usr/sbin/nsm
admin      858  0.0  2.3 15640 5216 ?        S    07:15   0:00 /usr/sbin/snmpd
admin      860  0.0  1.4 13172 3212 ?        S    07:15   0:00 /usr/sbin/dhcpd
admin      862  0.0  1.2 12532 2748 ?        S    07:15   0:00 /usr/sbin/dhcp6d
admin      864  0.0  1.1 12312 2560 ?        S    07:15   0:00 /usr/sbin/sflowd
admin      866  0.0  1.1 12356 2584 ?        S    07:15   0:00 /usr/sbin/eapd
admin      870  0.0  1.1 12428 2608 ?        S    07:15   0:00 /usr/sbin/sfpmond
admin      872  0.0  1.1 12208 2488 ?        S    07:15   0:00 /usr/sbin/swatchdogd
admin      874  0.0  0.2  2184  528 ?        S    07:15   0:00 /usr/sbin/mtbd
admin      879  0.1  2.0 15372 4612 ?        Ss   07:15   0:01 /usr/sbin/imi -d
admin      881  0.0  0.3  4912  672 ?        Ss   07:15   0:00 /usr/sbin/inetd
admin      888  0.0  0.1  2256  384 ?        Ss   07:15   0:00 klogd -c 1
admin      889  0.0  0.3  3840  876 ttyS0    Ss   07:15   0:00 init         
admin      892  0.1  0.4  5744  892 ?        Ss   07:15   0:01 /usr/sbin/sshd
admin      900  0.0  0.2  2576  604 ?        Ss   07:15   0:00 /sbin/syslogd -m 0
admin      903  0.0  0.2  2380  620 ttyS0    S    07:15   0:00 -sh
admin      908  0.1  2.5 15464 5688 ttyS0    S    07:15   0:01 /usr/sbin/vtysh
admin      923  0.0  0.2  2380  628 ttyS0    S    07:19   0:00 sh
admin      950  0.0  0.3  3352  828 ttyS0    R+   07:39   0:00 ps uwwax
*SWITCH# 


Kernel dmesg>>
 
*SWITCH# dmesg
CPU revision is: 00019749 (MIPS 74Kc. M32R2)
Determined physical RAM map:
 memory: 07fffe00 @ 00000000 (usable)
 memory: 07fff000 @ 87fff000 (usable)
Initrd not found or empty - disabling initrd
On node 0 totalpages: 65534
free_area_init_node: node 0, pgdat 812ffd60, node_mem_map 837b5000
  Normal zone: 0 pages reserved
  Normal zone: 32767 pages, LIFO batch:7
  HighMem zone: 32767 pages, LIFO batch:7
Cold Boot
Kernel command line: rdinit=/sbin/init console=ttyS0,9600
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=800009b0
Readback ErrCtl register=800009b0
Cache parity protection enabled
Memory: 186224k/131068k available (11711k kernel code, 75584k reserved, 7746k data, 35368k init, 131068k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
CPU: BCM5300 rev 1 at 400 MHz
i2c-core: driver [dummy] registered
pci 0000:00:00.0: reg 10 32bit mmio: [0x18000000-0x1800000f]
pci 0000:00:01.0: reg 10 32bit mmio: [0x18002000-0x1800200f]
pci 0000:00:04.0: reg 10 32bit mmio: [0x18005000-0x1800500f]
pci 0000:00:04.0: reg 38 32bit mmio pref: [0x000000-0x0007ff]
pci 0000:00:05.0: reg 10 32bit mmio: [0x1800e000-0x1800e00f]
pci 0000:00:05.0: reg 38 32bit mmio pref: [0x000000-0x0007ff]
pci 0000:00:06.0: reg 10 32bit mmio: [0x18006000-0x1800600f]
pci 0000:00:07.0: reg 10 32bit mmio: [0x18007000-0x1800700f]
pci 0000:00:08.0: reg 10 32bit mmio: [0x18008000-0x1800800f]
pci 0000:01:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
pci 0000:01:00.0: reg 18 64bit mmio: [0x000000-0x7ffffff]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.1: reg 10 64bit mmio: [0x000000-0x003fff]
pci 0000:01:00.1: reg 18 64bit mmio: [0x000000-0x7ffffff]
pci 0000:01:00.1: supports D1 D2
pci 0000:01:01.0: reg 10 64bit mmio: [0x000000-0x03ffff]
pci 0000:00:04.0: bridge io port: [0x00-0xfff]
pci 0000:00:04.0: bridge 32bit mmio: [0x000000-0x0fffff]
pci 0000:00:04.0: bridge 32bit mmio pref: [0x000000-0x0fffff]
pci 0000:00:05.0: bridge io port: [0x00-0xfff]
pci 0000:00:05.0: bridge 32bit mmio: [0x000000-0x0fffff]
pci 0000:00:05.0: bridge 32bit mmio pref: [0x000000-0x0fffff]
pci 0000:11:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
pci 0000:11:00.0: reg 18 64bit mmio: [0x000000-0x7ffffff]
pci 0000:11:00.0: supports D1 D2
pci 0000:11:00.1: reg 10 64bit mmio: [0x000000-0x003fff]
pci 0000:11:00.1: reg 18 64bit mmio: [0x000000-0x7ffffff]
pci 0000:11:00.1: supports D1 D2
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
0x000000300000-0x000000400000 : "NOS Config"
0x000000300000-0x000002000000 : "(Reserved) NVRAM"
0x0000001e0000-0x000000200000 : "BOOT-CONFIG user env"
0x0000001c0000-0x0000001e0000 : "BOOT-CONFIG root env"
0x000000200000-0x000000300000 : "NVRAM Area"
0x000000400000-0x000001200000 : "NOS-1"
0x000001200000-0x000002000000 : "NOS-2"
0x000000000000-0x000000100000 : "Boot Loader"
i2c-core: driver [rtc-ds1307] registered
i2c-core: driver [dev_driver] registered
i2c i2c-0: adapter [BCM5300X_I2C_0] registered
i2c 0-0002-0068: uevent
rtc-ds1307 0-0002-0068: rtc core: registered m41t00 as rtc0
rtc-ds1307 0-0002-0068: 56 bytes nvram
i2c i2c-0: client [m41t00] registered with bus id 0-0002-0068
i2c 0-0003-004a: uevent
i2c i2c-0: client [ds75] registered with bus id 0-0003-004a
i2c 0-0001-0050: uevent
i2c i2c-0: client [sfp_gpio] registered with bus id 0-0001-0050
i2c 0-0005-0050: uevent
i2c i2c-0: client [sfp_gpio] registered with bus id 0-0005-0050
i2c 0-0000-0050: uevent
i2c i2c-0: client [sfp_gpio] registered with bus id 0-0000-0050
i2c 0-0004-0050: uevent
i2c i2c-0: client [sfp_gpio] registered with bus id 0-0004-0050
i2c-dev: adapter [BCM5300X_I2C_0] registered as minor 0
i2c i2c-1: adapter [BCM5300X_I2C_1] registered
i2c-dev: adapter [BCM5300X_I2C_1] registered as minor 1
i2c-core: driver [sfp_gpio] registered
i2c-core: driver [pca954x] registered
ds75 0-0003-004a: hwmon0: sensor 'ds75'
i2c-core: driver [ds75] registered
bcm53000_wdt: Hardware Watchdog Timer for bcm53000 
i2c-core: driver [is24c] registered
i2c i2c-0: found normal entry for adapter 0, addr 0x50
i2c i2c-1: found normal entry for adapter 1, addr 0x50
PCI: Setting latency timer of device 0000:00:01.0 to 64
found pci device 14e4:b142 as ether_dev
_init: Switching started.
Freeing unused kernel memory: 35368k freed
port  1 link up(administrative)
port  2 link up(administrative)
port  3 link up(administrative)
port  4 link up(administrative)
port  5 link up(administrative)
port  6 link up(administrative)
port  7 link up(administrative)
port  8 link up(administrative)
port  9 link up(administrative)
port 10 link up(administrative)
port 11 link up(administrative)
port 12 link up(administrative)
port 13 link up(administrative)
port 14 link up(administrative)
port 15 link up(administrative)
port 16 link up(administrative)
port 17 link up(administrative)
port 18 link up(administrative)
port 19 link up(administrative)
port 20 link up(administrative)
port 21 link up(administrative)
port 22 link up(administrative)
port 23 link up(administrative)
port 24 link up(administrative)
port 25 link up(administrative)
port 26 link up(administrative)
port 27 link up(administrative)
port 28 link up(administrative)
port 29 link up(administrative)
port 30 link up(administrative)
port 31 link up(administrative)
port 32 link up(administrative)
port 33 link up(administrative)
port 34 link up(administrative)
port 35 link up(administrative)
port 36 link up(administrative)
port 37 link up(administrative)
port 38 link up(administrative)
port 39 link up(administrative)
port 40 link up(administrative)
port 41 link up(administrative)
port 42 link up(administrative)
port 43 link up(administrative)
ADDRCONF(NETDEV_UP): default: link is not ready
port  1 link up(administrative)
port  2 link up(administrative)
port  3 link up(administrative)
port  4 link up(administrative)
port  5 link up(administrative)
port  6 link up(administrative)
port  7 link up(administrative)
port  8 link up(administrative)
port  9 link up(administrative)
port 10 link up(administrative)
port 11 link up(administrative)
port 12 link up(administrative)
port 13 link up(administrative)
port 14 link up(administrative)
port 15 link up(administrative)
port 16 link up(administrative)
port 17 link up(administrative)
port 18 link up(administrative)
port 19 link up(administrative)
port 20 link up(administrative)
port 21 link up(administrative)
port 22 link up(administrative)
port 23 link up(administrative)
port 24 link up(administrative)
port 25 link up(administrative)
port 26 link up(administrative)
port 27 link up(administrative)
port 28 link up(administrative)
INIT: Start UP
*SWITCH#
PCI devices>>
 
*SWITCH# lspci -vvnnxx
00:00.0 FLASH memory [0501]: Broadcom Corporation Device [14e4:0500] (rev 01)
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Region 0: Memory at 18000000 (32-bit, non-prefetchable) [disabled] [size=16]
00: e4 14 00 05 00 00 00 00 01 00 01 05 00 00 00 00
10: 00 00 00 18 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:01.0 Ethernet controller [0200]: Broadcom Corporation Sentry5 USB Controller [14e4:4715] (rev 01)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Interrupt: pin B routed to IRQ 4
	Region 0: Memory at 18002000 (32-bit, non-prefetchable) [size=16]
	Kernel driver in use: et
00: e4 14 15 47 06 00 00 00 01 00 00 02 00 40 00 00
10: 00 20 00 18 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 04 02 00 00

00:04.0 PCI bridge [0604]: Broadcom Corporation Device [14e4:0820] (rev 01) (prog-if 00 [Normal decode])
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF+ FastB2B+ ParErr+ DEVSEL=?? >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx+
	Region 0: Memory at 18005000 (32-bit, non-prefetchable) [disabled] [size=16]
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00000000-00000fff
	Memory behind bridge: 00000000-000fffff
	Prefetchable memory behind bridge: 00000000-000fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00: e4 14 20 08 00 00 ff ff 01 00 04 06 00 00 01 00
10: 00 50 00 18 00 00 00 00 00 01 01 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 05 00 00

00:05.0 PCI bridge [0604]: Broadcom Corporation Device [14e4:0820] (rev 01) (prog-if 00 [Normal decode])
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF+ FastB2B+ ParErr+ DEVSEL=?? >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx+
	Region 0: Memory at 1800e000 (32-bit, non-prefetchable) [disabled] [size=16]
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: 00000000-00000fff
	Memory behind bridge: 00000000-000fffff
	Prefetchable memory behind bridge: 00000000-000fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00: e4 14 20 08 00 00 ff ff 01 00 04 06 00 00 01 00
10: 00 e0 00 18 00 00 00 00 00 02 02 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 06 01 00 00

00:06.0 RAM memory [0500]: Broadcom Corporation Device [14e4:052e] (rev 01)
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin F routed to IRQ 14
	Region 0: Memory at 18006000 (32-bit, non-prefetchable) [disabled] [size=16]
00: e4 14 2e 05 00 00 00 00 01 00 00 05 00 00 00 00
10: 00 60 00 18 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0e 06 00 00

00:07.0 RAM memory [0500]: Broadcom Corporation Device [14e4:050e] (rev 01)
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin H routed to IRQ 16
	Region 0: Memory at 18007000 (32-bit, non-prefetchable) [disabled] [size=16]
00: e4 14 0e 05 00 00 00 00 01 00 00 05 00 00 00 00
10: 00 70 00 18 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 10 08 00 00

00:08.0 Unassigned class [ffff]: Broadcom Corporation Device [14e4:0534] (rev 01) (prog-if ff)
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin G routed to IRQ 15
	Region 0: Memory at 18008000 (32-bit, non-prefetchable) [disabled] [size=16]
00: e4 14 34 05 00 00 00 00 01 ff ff ff 00 00 00 00
10: 00 80 00 18 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 07 00 00

01:00.0 Host bridge [0600]: Broadcom Corporation Device [14e4:5300] (rev 01)
	Subsystem: Broadcom Corporation Device [14e4:5300]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 2
	Region 0: Memory at <unassigned> (64-bit, non-prefetchable)
	Region 2: Memory at <unassigned> (64-bit, non-prefetchable)
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=2 PME-
	Capabilities: [58] Vendor Specific Information: Len=78 <?>
	Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [d0] Express (v1) Root Port (Slot-), MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
			ExtTag+ RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 256 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <4us, L1 <64us
			ClockPM+ Surprise+ LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [13c v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 00-00-00-ff-ff-00-00-00
	Capabilities: [16c v1] Power Budgeting <?>
00: e4 14 00 53 06 00 10 00 01 00 00 06 08 00 80 00
10: 04 00 00 00 00 00 00 00 04 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 e4 14 00 53
30: 00 00 00 00 40 00 00 00 00 00 00 00 02 01 00 00

01:00.1 Host bridge [0600]: Broadcom Corporation Device [14e4:0000] (rev 01)
	Subsystem: Broadcom Corporation Device [14e4:5300]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 2
	Region 0: Memory at <unassigned> (64-bit, non-prefetchable)
	Region 2: Memory at <unassigned> (64-bit, non-prefetchable)
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=2 PME-
	Capabilities: [58] Vendor Specific Information: Len=78 <?>
	Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [d0] Express (v1) Root Port (Slot-), MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
			ExtTag+ RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <4us, L1 <64us
			ClockPM+ Surprise+ LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [13c v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 00-00-00-ff-ff-00-00-00
	Capabilities: [16c v1] Power Budgeting <?>
00: e4 14 00 00 46 01 10 00 01 00 00 06 08 00 80 00
10: 04 00 00 00 00 00 00 00 04 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 e4 14 00 53
30: 00 00 00 00 40 00 00 00 00 00 00 00 02 01 00 00

01:01.0 Ethernet controller [0200]: Broadcom Corporation Device [14e4:b142] (rev 02)
	Subsystem: Broadcom Corporation Device [14e4:b142]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at 08000000 (64-bit, non-prefetchable) [size=256K]
	Capabilities: [48] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
	Capabilities: [50] Vital Product Data
pcilib: sysfs_read_vpd: read failed: Connection timed out
		Not readable
	Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [a0] MSI-X: Enable- Count=1 Masked-
		Vector table: BAR=0 offset=00000000
		PBA: BAR=0 offset=00000000
	Capabilities: [ac] Express (v2) Endpoint, MSI 00
		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <4us
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
		LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
			 Compliance De-emphasis: -6dB
		LnkSta2: Current De-emphasis Level: -6dB
	Capabilities: [100 v1] Device Serial Number 00-00-00-00-00-00-00-00
	Capabilities: [110 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [150 v1] Power Budgeting <?>
	Capabilities: [160 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Kernel driver in use: linux-kernel-bde
00: e4 14 42 b1 46 01 10 08 02 00 00 02 08 00 00 00
10: 04 00 00 08 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 e4 14 42 b1
30: 00 00 00 00 48 00 00 00 00 00 00 00 05 01 00 00

11:00.0 Host bridge [0600]: Broadcom Corporation Device [14e4:5300] (rev 01)
	Subsystem: Broadcom Corporation Device [14e4:5300]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 2
	Region 0: Memory at <unassigned> (64-bit, non-prefetchable)
	Region 2: Memory at <unassigned> (64-bit, non-prefetchable)
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=2 PME-
	Capabilities: [58] Vendor Specific Information: Len=78 <?>
	Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [d0] Express (v1) Root Port (Slot-), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
			ExtTag+ RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <4us, L1 <64us
			ClockPM+ Surprise+ LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [13c v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 00-00-00-ff-ff-00-00-00
	Capabilities: [16c v1] Power Budgeting <?>
00: e4 14 00 53 06 00 10 00 01 00 00 06 00 00 80 00
10: 04 00 00 00 00 00 00 00 04 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 e4 14 00 53
30: 00 00 00 00 40 00 00 00 00 00 00 00 02 01 00 00

11:00.1 Host bridge [0600]: Broadcom Corporation Device [14e4:0000] (rev 01)
	Subsystem: Broadcom Corporation Device [14e4:5300]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 2
	Region 0: Memory at <unassigned> (64-bit, non-prefetchable)
	Region 2: Memory at <unassigned> (64-bit, non-prefetchable)
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=2 PME-
	Capabilities: [58] Vendor Specific Information: Len=78 <?>
	Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [d0] Express (v1) Root Port (Slot-), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
			ExtTag+ RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <4us, L1 <64us
			ClockPM+ Surprise+ LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
	Capabilities: [13c v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [160 v1] Device Serial Number 00-00-00-ff-ff-00-00-00
	Capabilities: [16c v1] Power Budgeting <?>
00: e4 14 00 00 06 00 10 00 01 00 00 06 00 00 80 00
10: 04 00 00 00 00 00 00 00 04 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 e4 14 00 53
30: 00 00 00 00 40 00 00 00 00 00 00 00 02 01 00 00

*SWITCH#