Image OK!
OK
No initrd
## Transferring control to Linux (at address 80002000) ...
## Giving linux memsize in bytes, 67108864
Starting kernel ...
Booting AR7240(Python)...
Linux version 2.6.31--LSDK-9.1.0.214 (release@J11) (gcc version 4.3.3 (GCC) ) #1 Fri Nov 15 13:40:04 CST 2013
flash_size passed from bootloader = 16
CPU revision is: 00019374 (MIPS 24Kc)
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock0 rw mem=64m
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 62204k/65536k available (2028k kernel code, 3264k reserved, 444k data, 124k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 266.24 BogoMIPS (lpj=532480)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
===== ar7240_platform_init: 0
PCI init:ar7240_pcibios_init
ar7240_pcibios_init(300): PCI CMD write: 0x356
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:00.0: PME# supported from D0 D1 D3hot
pci 0000:00:00.0: PME# disabled
Returning IRQ 48
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
AR7240 GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 121
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
brd: module loaded
ELBOX CFI physmap flash device: 1000000 at 9f000000
AR7240 serial flash !!
ar7240-nor0: squashfs filesystem found at offset 0x00150000
Creating 10 MTD partitions on "ar7240-nor0":
0x0000001500c0-0x000001000000 : "rootfs"
0x000000070000-0x000000fe0000 : "upgrade"
0x000000050000-0x000000060000 : "rgdb"
0x000000040000-0x000000050000 : "bdcfg"
0x000000060000-0x000000070000 : "langpack"
0x000000fe0000-0x000000ff0000 : "certificate"
0x000000ff0000-0x000001000000 : "radiocfg"
0x000000000000-0x000001000000 : "flash"
0x000000000000-0x000000040000 : "bootloader"
0x000000040000-0x000000050000 : "boot config"
u32 classifier
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ar7240wdt_init: Registering WDT success
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 124k freed
init started: BusyBox v1.14.1 (2013-11-15 13:40:09 CST)
starting pid 130, tty '': '/etc/init.d/rcS'
[/etc/init.d/S03config.sh]
Mounting proc and var ...
SymbLink /dev/mtdblock/0
SymbLink /dev/mtdblock/1
SymbLink /dev/mtdblock/2
SymbLink /dev/mtdblock/3
SymbLink /dev/mtdblock/4
SymbLink /dev/mtdblock/5
SymbLink /dev/mtdblock/6
SymbLink /dev/mtdblock/7
SymbLink /dev/mtdblock/8
SymbLink /dev/mtdblock/9
Inserting kernel modules ...
Inserting Rebootm ...
Rebootm loading ...
Inserting atheros ethernet ...
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: Mac address for unit 0
ATHR_GMAC: 00:03:7f:e0:08:44
ATHR_GMAC: Max segments per packet 1
ATHR_GMAC: Max tx descriptor count 40
ATHR_GMAC: Max rx descriptor count 252
ATHR_GMAC: Mac address for unit 1
ATHR_GMAC: 00:03:7f:e0:08:45
MAC:1 Warning: Phy not found!!!
ATHR_GMAC: Max segments per packet 1
ATHR_GMAC: Max tx descriptor count 40
ATHR_GMAC: Max rx descriptor count 252
Inserting gpio ...
GPIO driver initialized.
done.
Start xmldb ...
[/etc/scripts/misc/profile.sh] getnew ...
[/etc/scripts/misc/defnodes.sh] ...
[/etc/defnodes/S10setext.sh] ...
PHP [/etc/defnodes/S11setnodes.php] ...
PHP [/etc/defnodes/S12features.php] ...
PHP [/etc/defnodes/S13flashspeed.php] ...
PHP [/etc/defnodes/S20setnodes.php] ...
mount: mounting /dev/mtdblock/4 on /www/locale/alt failed: Invalid argument
PHP [/etc/defnodes/S40brand.php] ...
[/etc/scripts/misc/defnodes.sh] Done !!
[/etc/templates/timezone.sh] ...
[/etc/templates/logs.sh] ...
[/var/run/logs_run.sh] ...
athr_gmac_ring_alloc Allocated 640 at 0x83981800
athr_gmac_ring_alloc Allocated 4032 at 0x83964000
WASP EMULATION ----> F1 PHY
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
ATHRSF1_PHY: Port 0, Neg Success
ATHRSF1_PHY: unit 0 phy addr 0
ADDRCONF(NETDEV_UP): eth0: link is not ready
[/etc/init.d/S03config.sh] done!
[/etc/init.d/S10system.sh]
start Layout ...
[/etc/scripts/layout.sh] start ...
[/var/run/layout_start.sh] ...
Start bridge layout ...
device eth0 entered promiscuous mode
start LAN ...
[/etc/templates/lan.sh] ...
[/var/run/lan_start.sh] ...
Bridge mode selected, LAN is disabled !
start web server ...
[/etc/templates/webs.sh] start ...
[/var/run/webs_start.sh] ...
Starting HTTPD ...
nvram: not found
nvram: not found
start eth0 vlan setup ...
/etc/scripts/eth_vlan.sh: not found
#!/bin/sh
echo [$0] ... > /dev/console
# limitedadmin.php <<<
limitedadmin.sh...
set eth0's MTU to 1500...
/etc/scripts/eth_vlan.sh: not found
start fresetd ...
Factory reset time : 5 secs
System reset time : 1 secs
WPS command : [/etc/templates/wps.sh pbc &]
enable LAN ports ...
[/etc/scripts/enlan.sh] ...
Generate channel table according to the country code...
Generate VLAN table according to the port...
start WAN ...
Set WAN port media type 0
[/etc/templates/wan.sh] start ...
[/var/run/wan_start.sh] ...
Bridge mode selected !
Start WAN(br0),192.168.0.50/255.255.255.0 ...
[/etc/templates/wanup.sh] ...
[/var/run/wan_up.sh] ...
[/etc/templates/ntp.sh] ...
killall: ntpclient: no process killed
NTP client is disabled ...
[/etc/templates/upnpd.sh] ...
[/var/run/upnpd_start.sh] ...
Starting UPnP ...
/etc/templates/webredirect.sh: not found
>>>/var/run/wan_start.sh: Start IPv6 configuration >>>
Disable IPv6.
<<< End of IPv6 <<<
nvram: not found
nvram: not found
start stunnel ...
[/etc/templates/stunnel.sh] ...
Setting certificate.
[/var/run/stunnel_start.sh] ...
Starting universal SSL tunnel: stunnel.
start WLAN ...
[/etc/templates/wlan.sh] ...
SERVD: stop service [WLAN]
SERVD: service [WLAN] is already stopped.
SERVD: start service [WLAN]
start telnet daemon ...
[/etc/templates/wlan_run.sh] start ...
Start telnetd ...
nvram: not found
[/etc/templates/autorekey.sh] ...
nvram: not found
start SSHD daemon ...
[/var/run/autorekey_start.sh] ...
[/etc/templates/sshd.sh] ...
start WLAN .....
[/var/run/sshd_start.sh] ...
start sshd ...
Disable start-up daemon: sshd.
start DHCP server
[/etc/templates/dhcpd.sh] ...
[/var/run/dhcpd_restart.sh] ...
Stop DHCP server (br0) ...
[/var/run/wlan_insmod.sh] ...
Start DHCP server (br0) ...
DHCP server is disabled!
start SNMP ...
asf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
[/etc/templates/snmp.sh] ...
start NEAP ...
[/etc/templates/neaps.sh] start ...
[/var/run/neaps_start.sh] ...
Start Neap Server ...
start NEAPC ...
[/etc/templates/neapc.sh] start ...
[/var/run/neapc_start.sh] ...
Start NeapC Client ...
Stop apneaps Server ...
: not found
start Microsoft LLDP ...
ath_hal: 0.9.17.1 (AR5416, AR9380, DEBUG, REGOPS_FUNC, WRITE_EEPROM, 11D)
[/etc/templates/lld2d.sh] ...
[/var/run/lld2d_ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
start.sh] ...
Start LLD2 daemon ...
start Ethlink ...
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
[/etc/templates/arpspoofing.sh] start ...
[/var/run/arpspoofing_start.sh] ...
Start arp spoofing prevention ...
arp spoofing prevention is disabled.
[/etc/init.d/S10system.sh] done!
rcS done!
Please press Enter to activate this console. ath_pci: 9.2.0_U11.14 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
ar5416 CtlData override
ath_get_caps[5291] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[5266] tx chainmask mismatch actual 3 sc_chainmak 0
wifi0: Atheros 9280: mem=0x10000000, irq=48 hw_base=0xb0000000
[/var/run/wlan_start.sh] ...
Start WLAN interface ath0 ...
wlan_vap_create : enter. devhandle=0x83b4c360, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x83b4c360, opmode=IEEE80211_M_HOSTAP, flags=0x1.
ath0
[/var/run/wlan_start.sh] ...
[/var/run/wlan_daemon_up.sh] ...
sleep 5.....
: not found
[/var/run/wlan_device_up.sh] ...
device ath0 entered promiscuous mode
ALPHA:[Wireless]Initiate Wireless ath0 success
ALPHA:[SNMP-TRAP][Specific=7]
br0: port 2(ath0) entering forwarding state
[/var/run/vlan_start.sh] ...
disable VLAN
[/etc/templates/lld2d.sh] ...
[/var/run/lld2d_stop.sh] ...
Stop LLD2 daemon ...
[/var/run/lld2d_start.sh] ...
Start LLD2 daemon ...
[/usr/sbin/submit] QOS_TC_TM ...
[/var/run/qos_stop.sh] ...
Interface is wanif=eth0 wlanif=ath0... OK
Stop QOS system ...
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such file or directory
[/var/run/qos_start.sh] ...
Interface is wanif=eth0 wlanif=ath0... OK
Start QOS system ...
QOS is disabled.
[/usr/sbin/submit] NETFILTER ...
[/usr/sbin/submit] ARP_SPOOFING ...
[/etc/templates/arpspoofing.sh] restart ...
[/var/run/arpspoofing_stop.sh] ...
Stop arp spoofing prevention...
[/var/run/arpspoofing_start.sh] ...
Start arp spoofing prevention ...
arp spoofing prevention is disabled.
starting pid 1821, tty '/dev/ttyS0': '-/bin/sh'
BusyBox v1.14.1 (2013-11-15 13:40:09 CST) built-in shell (msh)
Enter 'help' for a list of built-in commands.
# ---Checking System Memory..OK, Current Free Memoey is 38020 KB
|