Belkin F9K1105 v1

multiple revisions of this device, use caution

abgn (N450)
N450 DB Wireless N Router
Support	Support page
Wikipedia	Belkin
WikiDevi.wi-cat.ru	Belkin F9K1105 v1
3rd Party Firmware
dd-wrt	Status Unknown
OpenWrt	Status Unknown
Tomato any flavor	Status Unknown
Platform
Brand • Model • Rev	Belkin F9K1105 v1
FCC ID	K7SF9K1105V1
IC ID	3623A-F9K1105V1
Type	wireless router
Series	F9K1105
CPU1	Broadcom BCM5358UB0
CPU1 Type	MIPS 74K
CPU1 Speed	500 MHz
Flash1 Chip	Macronix MX25L6406EM2I-12G
Flash1 Size	8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br />
RAM1 Size	64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br />
RAM1 Chip	EtronTech EM6AB160TSC-5G
ETH chip1	Broadcom BCM5358UB0
Switch	Broadcom BCM5358UB0
Ethernet Port Count	1-100MbE-WAN 4-100MbE-LAN
Wired Standard	IEEE 802.3i/3u
802dot11 OUI: 08:86:3B (10 E, 14 W) Ethernet OUI: 08:86:3B (10 E, 14 W)
Expansion IF types	none specified
Power	12 VDC, 1 A
Connector type	barrel
Serial Port (UART)	yes, internal, 4-pin header, populated, 3.3V TTL, J3
Other
Default SSID: belkin.XXX (19 addl. devices) , belkin.XXX.5GHz (5 addl. devices) Default IP address: 192.168.2.1 the IP 192.168.2.1 is used by 297 additional devices of which 99 are Belkin devices
Manuf/OEM/ODM	Arcadyan WG8005G12 -AK
Retail
FCC approval date	31 May 2011
UPC	722868829905 (UPC DB, On eBay)
ASIN	B005CUVPMK ,  multiple uses
Country of manuf	China
Radio 1
Chip1	Broadcom BCM5358UB0
Wireless interface OUI	08:86:3B
Antenna Connector Type	none
MIMO status	1x1:1
Wireless Standard	IEEE 802.11b/g/n
802.11n	up to 150 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio cor_rev	28
Radio 2
Chip1	Broadcom BCM43236
Wireless interface OUI	08:86:3B
Antenna Connector Type	U.FL
MIMO status	2x2:2
Wireless Standard	IEEE 802.11a/n
802.11n	up to 300 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
Radio cor_rev	24
CPU1 brand Radio1 chip1 brand Radio2 chip1 brand Belkin F9K1105 v1 Broadcom Broadcom Broadcom Belkin F9K1105 v2 Realtek Realtek Realtek Belkin F9K1105 v3 Broadcom Broadcom Broadcom

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.

For a list of all currently documented Belkin device with specifications, see Belkin.

• 450 Mbps - 3SS 2.4GHz 802.11n (40MHz chan.) = N450 class

Overview

A triangular RoHS notice and "P/N: 141801620000J R01A" is silkscreened on one production model board.

The default SSID pattern is belkin.XXX (and also [probably] belkin.XXX.5 GHz) where XXX is the last three hex digits of the wireless interface MAC address (lower case letters). An example SSID set is belkin.0a2 and belkin.0a2.5 GHz where the WLAN MAC is 08:86:3B:93:10:A2.

• Wi-Fi Certified : WFA11640 (as of 05/09/2011)

Links of Interest

• https://routerchart.com/belkin/belkin-n450-db-f9k1105-f9k1105-140

JTAG-Serial Info

Serial

boot log

Decompressing...done Init Arena Init Devs. Boot partition size = 131072(0x20000) Found a 8MB ST compatible serial flash et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.127.10 CPU type 0x19749: 530MHz Tot mem: 65536 KBytes CFE mem: 0x80700000 - 0x807A0220 (655904) Data: 0x80735E40 - 0x80739060 (12832) BSS: 0x80739060 - 0x8073A220 (4544) Heap: 0x8073A220 - 0x8079E220 (409600) Stack: 0x8079E220 - 0x807A0220 (8192) Text: 0x80700000 - 0x80735E3C (220732) Copying boot params..... DONE Bootloader version v0.02 boot_version v0.02 Project name : WG8015G12-AK Press space bar to cancel startup... Device eth0: hwaddr 08-86-3B-45-BB-23, ipaddr 192.168.2.1, mask 255.255.255.0 gateway not set, nameserver not set Loader:raw Filesys:raw Dev:flash0.os File: Options:(null) Loading: ....... 4232460 bytes read Entry at 0x80001000 Closing network. Starting program at 0x80001000 Linux version 2.6.22 (tony_fu@SW3SRV2.arcadyan.com.tw) (gcc version 4.1.2) #34 Tue Jun 5 09:27:09 CST 2012 CPU revision is: 00019749 Found a 8MB ST compatible serial flash wombo_reset set to gpio 22 Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Built 1 zonelists. Total pages: 16256 Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 256 (order: 8, 1024 bytes) CPU: BCM5357 rev 2 at 530 MHz Using 265.000 MHz high precision timer. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 60312k/65536k available (2815k kernel code, 5160k reserved, 1140k data, 176k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: no core PCI: Fixing up bus 0 Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered gpio_init 156 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher fuse init (API version 7.8) io scheduler noop registered (default) Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A loop: module loaded PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 pflash: found no supported devices sflash: squash filesystem with lzma found at block 1722 Creating 4 MTD partitions on "sflash": 0x00000000-0x00030000 : "boot" 0x00030000-0x007f0000 : "linux" 0x001aeb94-0x007f0000 : "rootfs" 0x007f0000-0x00800000 : "nvram" usbmon: debugfs is not available GACT probability on Mirror/redirect action on u32 classifier input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (512 buckets, 4096 max) ctnetlink v0.93: registering with nfnetlink. BCM fast NAT: INIT ip_tables: (C) 2000-2006 Netfilter Core Team ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 176k freed Warning: unable to open an initial console. Failed to execute /init Algorithmics/MIPS FPU Emulator v1.5 [sighandler]: No more events to be processed, quitting. [cleanup]: Waiting for children. [cleanup]: All children terminated. insmod: emf.ko: no module by that name found insmod: igs.ko: no module by that name found insmod: bcm57xx.ko: no module by that name found insmod: usbcore.ko: no module by that name found wl1 is up in 0 sec Hit enter to continue...vlan2: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Invalid argument wlconf: PHYTYPE: 4 eth1: Invalid argument eth1: Invalid argument eth1: Operation not supported eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument wlconf: PHYTYPE: 4 eth2: Invalid argument eth2: Operation not supported eth2: Invalid argument eth2: Invalid argument eth2: Invalid argument eth2: Invalid argument eth2: Invalid argument NET: Setting wl0.1 hw addr to 0A:86:3B:45:BB:24 NET: Error setting hw for wl0.1; returned -1 HTTPD: main(1136) killall: wps_monitor: no process killed killall: wps_ap: no process killed killall: wps_enr: no process killed UPnP daemon is ready to run mkdir: cannot create directory '/tmp/mnt': File exists mkdir: cannot create directory '/tmp/etc': File exists mkdir: cannot create directory '/tmp/etc/sysconfig': File exists Starting HotPlug: /usr/sbin/hotplugd -D -f Starting jcpd daemon: /usr/sbin/jcpd insmod: cannot insert '/lib/modules/2.6.22/kernel/drivers/usb/host/ehci-hcd.ko': Invalid parameters (17): Invalid argument share memory key=74565 successful id on creating=32769 original zone=GMT-1 modified dst=GMT udhcpd_main(138): udhcp server (v0.9.8) started read_conf_data(133): dhcp_client_list_num :[1] udhcpd_main(138): udhcp server (v0.9.8) started [start_wan 1157], ifconfig vlan1 up vlan1: Operation not supported udhcpc_main(438): udhcp client (v0.9.8) started original zone=GMT-1 modified dst=GMT vlan1 dhcp vlan1: No such process Stop DDNS service! Hit enter to continue...Starting Samba: /usr/sbin/smbd -D /usr/sbin/nmbd -D Setting SSID: "belkin.b23" main(1300) wl -i eth1 ssid -C 10 belkin.b23 Setting SSID: "belkin.b23.5GHz" main(1312) wl -i eth2 ssid -C 15 belkin.b23.5GHz start_wl(1015) reStart the Wireless, lan_ifNames=vlan2 eth1 eth2 start_wl(1074), vlan2 start up start_wl(1076), eth1 start up start_wl(1079), eth2 start up guest enable, restart eth1 eth1: Operation not supported eth1: Operation not supported eth1: Invalid argument wlconf: PHYTYPE: 4 eth1: Invalid argument eth1: Invalid argument eth1: Operation not supported eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument Starting sxuptpd eth1: Invalid argument Initializing USB port mode: port1 = NAS port2 = NAS eth1: Invalid argument Starting usbjcpd eth1: Invalid argument eth1: Invalid argument Hit enter to continue...eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument eth1: Invalid argument Hit enter to continue...original zone=GMT-1 modified dst=GMT Portrd: Add iptable command: iptables -t nat -A POSTROUTING -s 192.168.2.0/24 -o vlan1 -j MASQUERADE iptables -t nat -A POSTROUTING -s 192.168.169.0/24 -o vlan1 -j MASQUERADE