Belkin F7D8301
abgn (AN600) | |||||
---|---|---|---|---|---|
Play N600 HD WIreless Dual-band N Router | |||||
Wikipedia | |||||
WikiDevi.wi-cat.ru | |||||
3rd Party Firmware | |||||
dd-wrt | |||||
OpenWrt |
Status Unknown | ||||
Tomato any flavor | |||||
Gargoyle |
Status Unknown | ||||
Platform | |||||
Brand • Model • Rev |
Belkin F7D8301 v1 | ||||
FCC ID | |||||
IC ID | |||||
Board ID |
141811720000J | ||||
Type |
wireless router | ||||
CPU1 |
Broadcom BCM4718A1 | ||||
CPU1 Type |
MIPS 74Kc | ||||
CPU1 Speed |
480 MHz | ||||
Flash1 Chip |
Eon EN29LV640B-90TIP | ||||
Flash1 Size |
8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br /> | ||||
RAM1 Size |
64 MiB67,108,864 B <br />524,288 Kib <br />65,536 KiB <br />512 Mib <br />0.0625 GiB <br /> | ||||
RAM1 Chip |
EtronTech EM68B16CWPA-25H | ||||
ETH chip1 |
Broadcom BCM4718A1 | ||||
Switch |
Broadcom BCM53115 | ||||
Ethernet Port Count |
1-1GbE-WAN 4-1GbE-LAN | ||||
Wired Standard |
IEEE 802.3i/3u/3ab | ||||
802dot11 OUI: none specified | |||||
Stock bootloader |
CFE 1.0.8e | ||||
Stock FW OS |
Linux 2.6.22 | ||||
Expansion IF types |
USB 2.0 | ||||
USB ports |
2 | ||||
USB Hub Compatible |
Untested | ||||
Power |
12 VDC, 2 A | ||||
Connector type |
barrel | ||||
Serial Port (UART) |
yes, 4-pin header, populated, 3.3V TTL, (115200 8N1), J3 | ||||
JTAG Port |
yes, 14-pin header, J2 | ||||
Additional chips | |||||
Other | |||||
Default SSID: belkin.XXXX (2 addl. devices) | |||||
Manuf/OEM/ODM |
Arcadyan WG8117F22 2-LF-AK | ||||
3rd Party Firmware Support | |||||
Retail | |||||
FCC approval date | 16 March 2010 | ||||
UPC |
722868813126 (UPC DB, On eBay) | ||||
ASIN | B0047T7AIU | ||||
Country of manuf | China | ||||
Radio 1 | |||||
Chip1 |
Broadcom BCM4718A1 | ||||
Wireless interface OUI |
none specified | ||||
Antenna Connector Type |
soldered | ||||
MIMO status |
2x2:2 | ||||
Wireless Standard |
IEEE 802.11b/g/n | ||||
802.11n |
up to 300 Mbps | ||||
802.11g |
up to 54 Mbps | ||||
802.11b |
up to 11 Mbps | ||||
WiFi Operating Frequency |
2.4 GHz | ||||
Radio cor_rev |
17 | ||||
Radio 2 | |||||
Chip1 |
Broadcom BCM43224 | ||||
Wireless interface OUI |
none specified | ||||
Antenna Connector Type |
U.FL (internal) | ||||
MIMO status |
2x2:2 | ||||
Wireless Standard |
IEEE 802.11a/n | ||||
802.11n |
up to 300 Mbps | ||||
802.11a |
up to 54 Mbps | ||||
WiFi Operating Frequency |
5 GHz | ||||
|
For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.
For a list of all currently documented Belkin device with specifications, see Belkin.
Overview
"P/N: 141811720000J REV: 01" is silkscreened on the board.
- It is reported that the device is working with the latest Toastman builds.
- .. and it would seem to be supported by Shibby's Tomato builds
The default SSID patterns for this device appear to be belkin.XXXX and belkin.XXXX.5ghz, where XXXX is the last two octets of the LAN interface MAC (lower case hex letters).
Links of Interest
- support for Belkin F7D8301 V1 (N600) or F7D4301v1 (Tomato)?
- Bricked Belkin F7D8302 v1 JTAG Fix/Solution (DD-WRT)
- Belkin Play Max F7D4301v1 now partially supported (DD-WRT)
- Belkin F7D8302v1 / F7D4302 v1 Serial Recovery Sollution (DD-WRT)
- New Belkin Routers (DD-WRT)
Flashing
NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Flashing dd-wrt
Please insert instructions here
Flashing Tomato
Please insert instructions here
JTAG-Serial Info
Serial
Serial Pinouts
J3 |> [+ TX RX -] or 1. 3.3 2. TX 3. RX 4. GND
Hyper terminal Setup in Windows XP
In Windows XP, Click Start Button - All Programs - Accessories - Communication - HyperTerminal Enter a name for the connection, Click ok Choose com port you adapter is plugged into, Click ok Set: Bits per second = 115200 Data Bits = 8 Parity = none Stop bits = 1 Flow control = none Click ok Click File - Save As, and select a place to save it to so you don't have to enter the settings again.
Putty Setup in Windows XP
After installing putty, run it Serial line = The COM port your using for serial (ie. COM3) Speed = 115200 Click on Serial under Connection Serial line to connect to = same as above (Serial line) Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Click Session Enter a name for your connection under saved sessions Click Save Click Open
Mincom setup in Linux
After installing minicom, run it with -s flag for setup (sudo minicom -s) Under "Serial Port Setup": Use 'A' to set the serial device (ie. /dev/ttyUSB0) Use 'E' to set the Bps/Par/Bits Speed (baud) = 115200 Data bits = 8 Stop bits = 1 Parity = None Flow control = None Save as dfl
Serial Recovery
- Clear the nvram
- Type ifconfig and you should get '=0', then it succeeded.
- Note the ip address listed and netmask address.
- After you have used the ifconfig command wait a minute or two.
- In your web browser got to the IP address noted in step 4.
- Upload DD-WRT mini image or original firmware.
Example:
CFE> nvram erase CFE> ifconfig =0 CFE>
TFTP Recovery
Coming Soon
USB Info
Pictures
Notes
F7D8301 v1 Chips
Broadcom Dual band (2.4 GHz/5GHz) Wireless Radio: BCM4718A1KFBG
Broadcom Smart Gigabit Switch: BCM53115SKFBG
EtronTech DDR2 32MX16BIT SDRAM: EM68B16CWPA-25h
cFeon NVRAM: EN29lV640B-90TIP
Sticker over cFeon NVRAM: WG8117F22 2-LF-AK
- Belkin
- Embedded system/wireless router
- Embedded System Broadcom
- Embedded System BCM4718A1
- Broadcom
- Embedded System MIPS 74Kc
- Embedded System
- Embedded System BCM53115
- Manuf Arcadyan
- DD-WRT Supported
- Tomato Supported
- Has Mimo Status
- Embedded System IEEE 802.11b/g/n
- Embedded System BCM43224
- Embedded System IEEE 802.11a/n
- Dual-Radio Wireless Embedded System
- Wireless Embedded System
- Dual-Band
- Retail Photo's Needed
- User Photo's Needed
- FCC Photo's Needed
- English Documentation