Belkin F5D8236-4 v2/Serial info

boot log

======================================================================= Wireless Router WG7005E22-LF-AK Loader v0.05 build Oct 22 2008 14:11:57 Arcadyan Technology Corporation ======================================================================= MXIC MX29LV160B bottom boot 16-bit mode found Copying boot params.....DONE Press Space Bar 3 times to enter command mode ... Flash Checking Passed. Unzipping firmware at 0x80002000 ... [ZIP 3] [ZIP 1] done In c_entry() function ... CPU : RT3052 Chip V1.2, CPU Speed 384 MHz, Interrups Status 00000000 install_exception Co config = 80050483 sys_irq_init ... ▒enter start_ralink_timer - 2 ##### _ftext = 0x80002000 ##### _fdata = 0x803647F0 ##### __bss_start = 0x8040AF3C ##### end = 0x80E22EFC ##### Backup Data from 0x803647F0 to 0x80E2AEFC~0x80ED1648 len 681804 ##### Backup Data completed ##### Backup Data verified [INIT] System Log Pool startup ... [INIT] MTinitialize .. [INIT] usrclk CPU Clock 384000000 Hz mips_counter_frequency:192000000 r4k_offset: 0x0002ee00(192000) init_US_counter : time1 = 299966 , time2 = 40299998, diff 40000032 US_counter = 48 cnt1 41401835 cnt2 41403103, diff 1268 mips_int_enable: 5 mips_int_enable 1: s = 8401 mips_int_enable 2: s = 8401 mips_int_enable 3: s = 0 Runtime code version: 2.00.04 System startup... [INIT] Memory COLOR 0, 800000 bytes .. [INIT] Memory COLOR 1, 600000 bytes .. [INIT] Memory COLOR 2, 607200 bytes .. MXIC MX29LV160B bottom boot 16-bit mode found Set flash memory layout to Boot Parameters found !!! Bootcode version: v0.05 Serial number: 12907823631234 Hardware version: 01 MXIC MX29LV160B bottom boot 16-bit mode found sizeof(struct III_Config_t) is 88256, nLen:88256, Magic:0xffffffff !![E-CFG-VER] Configuration data version mismatch!! !![E-CFG-VER] Adapting factory defaults!! !![E-CFG-VER] Reconfiguration required!! !!No configuration file present!! !!! Invalid wireless channel range 0 ~ 0 !!! Use default value 1 ~ 13 default route: 0.0.0.0 BufferInit: BUF_HDR_SZ=160 BUF_ALIGN_SZ=28 BUFFER_OFFSET=384 BUF_BUFSZ0=544 BUF_BUFSZ1=4320 NUM_OF_B0=0 NUM_OF_B1=900 BUF_POOL0_SZ=0 BUF_POOL1_SZ=4032000 sizeof(BUFFER0)=704,sizeof(BUFFER1)=4480 *BUF0=0x80b426b8 *BUF1=0x8076a098 Altgn *BUF0=0x80b426c0 *BUF1=0x8076a0a0 End at BUF0:0x80b426c0, BUF1:0x80b426a0 BUF0[0]=0x80b426c0 BUF1[0]=0x8076a0a0 buffer0 pointer init OK! buffer1 pointer init OK! ifno= 0, Link_Type= 4 time = 08/01/2003, 00:00:00 Interface 0 ip = 127.0.0.1 ifno= 1, Link_Type= 1 need to reset Ethernet switch???? GDMA1_MAC_ADRH -- : 0x00000022 GDMA1_MAC_ADRL -- : 0x75489dd7 RA2880 Ethernet Driver Initilization. v1.60 256 rx/tx descriptors allocated. NAPI enable, Tx Ring = 256, Rx Ring = 256 phy_tx_ring = 0x0040c630, tx_ring = 0xA040C630, size: 16 bytes phy_rx_ring = 0x0040d630, rx_ring = 0xA040D630, size: 16 bytes GDMA1_FWD_CFG = 10000 mips_int_enable: 3 mips_int_enable 1: s = 8400 mips_int_enable 2: s = a400 mips_int_enable 3: s = 0 MAC Address: 00:22:75:48:9d:d7 time = 08/01/2003, 00:00:00 Interface 1 ip = 192.168.2.1 ifno= 2, Link_Type= 1 hwlan_init(384): [HWLAN] ifno=2 irno=7 port=0x00000000 2860 version : 1.9.0.0 (Nov 12 2008) RTMP_ADAPTER_mem : 804c8bb4, sizeof(RTMP_ADAPTER) 391008 === pAd = 804C8BB4, size = 391008 === <-- RTMPAllocAdapterBlock, Status=0 RUNTASK id=1 hwlan_light_isr... time = 08/01/2003, 00:00:00 Interface 2 ip = 192.168.2.1 ifno= 3, Link_Type= 1 MAC Address: 00:22:75:48:9d:d8 time = 08/01/2003, 00:00:00 iput_IpLinkUp(ifno=3)> ifp->add_default_route:1 Re-Init NAT data structure Init NAT data structure Interface 3 ip = 0.0.0.0 ifno= 4, Link_Type= 0 ifno= 5, Link_Type= 0 ifno= 6, Link_Type= 0 ifno= 7, Link_Type= 0 ifno= 8, Link_Type= 0 ifno= 9, Link_Type= 0 ifno= 10, Link_Type= 0 ifno= 11, Link_Type= 0 ifno= 12, Link_Type= 0 ifno= 13, Link_Type= 0 ifno= 14, Link_Type= 0 ifno= 15, Link_Type= 0 ifno= 16, Link_Type= 0 ruleCheck()> Group: 0, Error: Useless rule index will be truncated ruleCheck()> Group: 1, Error: Useless rule index will be truncated ruleCheck()> Group: 2, Error: Useless rule index will be truncated ruleCheck()> Group: 3, Error: Useless rule index will be truncated CBAC rule format check succeed !! reqCBACBuf()> init match pool, Have: 1000 Memory Address: 0x80dd2194 ~ 0x80dd8f10 reqCBACBuf()> init timeGap pool, Have: 10000 Memory Address: 0x80dd8f10 ~ 0x80e09c64 reqCBACBuf()> init sameHost pool, Have: 2000 Memory Address: 0x80e09c64 ~ 0x80e19684 [setClsfyEnable] clsfy_func=0 CBAC rule pool initialized !! Init NAT data structure No default route, no need to reinit the NAT data structure RUNTASK id=2 if_task if0... RUNTASK id=3 if_task if1... RUNTASK id=4 if_task if2... RUNTASK id=5 if_task if3... RUNTASK id=6 timer_task... RUNTASK id=7 conn_mgr... RUNTASK id=8 main_8021x... RUNTASK id=9 main_lltd... RUNTASK id=10 period_task... RUNTASK id=11 belkin_goodie_task... RUNTASK id=12 dhcp_daemon... RUNTASK id=13 dhcp_clt...on interface 3 RUNTASK id=14 pptp_callmgr... RUNTASK id=15 L2tpd... found signature: 78h 56h 34h 12h ulImgLens=948129, LENGTH[3]-12=1769460 length checking OK [0] find End at 0xBFD27400 len=948129 ---[ LZMA head start in 0xBFD27800 ]--- found signature: 78h 56h 34h 12h ulImgLens=97424, LENGTH[3]-12=1769460 length checking OK [1] find End at 0xBFD3F400 len=97424 Image[1] at 0xBFC40000, len = 948129 Image[2] at 0xBFD27800, len = 97424 Unzipping from BFD27800 to 80ED2000 ... [ZIP 1] done Uncompressed size = 990253 drive start addr[0]=80ed2000, [1]=80fc3c30 [HTTPD] flash_init: failed!! httpd: listen at 192.168.2.1:80 RUNTASK httpd... RUNTASK id=18 dnsproxy... RUNTASK id=19 rip... RUNTASK id=20 ripout... RUNTASK id=21 dhcpd_mgmt_task... UPnP is enabled UPNP Device initialize success! slot=22 >>> belkin_wan_cfg task runs successfully, task_id = 23 gConfig.WSC_Mode:1 RUNTASK id=24 wscmain... RUNTASK id=25 wsc_Send_eap_packet... RUNTASK id=26 wsc_Send_UPNP_packet... RUNTASK id=27 WSC_WaitUserAction_Task... gConfig.WSC_Mode:1 UART RX Input Starting Multitask... run_project_task RUNTASK id=28 apAppInit... ifno2dot1x_if[2]=0 dot1x_wireless_if_mask=0x4 mips_int_enable: 4 mips_int_enable 1: s = a400 mips_int_enable 2: s = e400 mips_int_enable 3: s = 0 rt2860_open : should call request_irq ???????????????????????? RX DESC A0417A30 size = 2048 <-- RTMPAllocTxRxRingMemory, Status=0 sizeof(RT2860AP_DAT) : 1314 Channel=6 1. Phy Mode = 9 2. Phy Mode = 9 sould check E2PROM MAC ????????????????? 3. Phy Mode = 9 MCS Set = ff ff 00 00 00 Main bssid = 00:22:75:48:9d:d7 <==== RTMPInitialize, Status=0 should Set up the Mac address ????????? 0x1300 = 00064380 [HWLAN] Ready [dhcp_clt] enable dhcp client in interface WAN[3] ********************************************* Wi-Fi Simple Config Application - Intel Corp. Version: Build 1.02, Nov 12 2008 10:50:46 ********************************************* Initializing stack... ---------in wsc init---------- ----------sizeof(uint32)=4 ----------sizeof(uint-long)=4 ----------sizeof(uint32)=2 @#*@#*@#*EAP-WSC: Entered eap_wsc_init *#@*#@*#@ wsc_Send_eap_packet:udpFdupnp_wcn:28;;udpFdupnp:2a WSC_WaitUserAction:wait user action:0 [HWLAN] [30] rapi_tmr_task running [24]pthread_cond_init: 0 [24]pthread_mutex_init: resource No. 34 [24]pthread_mutex_init: resource No. 35 [PORTABLITY]:WscCreateThread-------------------- Entered udp_read upnp_Init: flag=0 SSDP Initialization completed... GenaInit : event_hook is NULL!! WscCmd:ActualCBThreadProc: Started [htf_dbg] - OnlineActiveWirless() 1633 [24]pthread_cond_init: 1 [24]pthread_mutex_init: resource No. 36 [24]pthread_mutex_init: resource No. 37 [PORTABLITY]:WscCreateThread-------------------- WscCmd:ActualUIThreadProc: Started. ActualUIThreadProc: wait q MasterControl constructor WscCmd::MC instantiated ok [24]pthread_cond_init: 2 [24]pthread_mutex_init: resource No. 38 [24]pthread_mutex_init: resource No. 39 [PORTABLITY]:WscCreateThread-------------------- [24]pthread_mutex_init: resource No. 40 [PORTABLITY]:pthread_mutex_init-------------------- CTransport Construction [24]pthread_cond_init: 3 [24]pthread_mutex_init: resource No. 41 [24]pthread_mutex_init: resource No. 42 [PORTABLITY]:WscCreateThread-------------------- In CTransport::ActualCBThreadProc ActualCBThreadProc: Calling Dequeue MC::Init: Init complete ok WscCmd::MC intialized ok WscCmd::Init ok, starting stack... Info::ReadConfigFile: Called Info::ReadConfigFile:P▒5▒ Info::ReadConfigFile:File open ok ******************uuid_p:0x00000000000000011000002275489dd7***** mp_deviceInfo->uuid[i]: 0-0-0-0-0-0-0-1-10-0-0-22-75-48-9d-d7- mp_deviceInfo->macAddr:00:22:75:48:9D:D7 gSetting.dot1x.if_entry[0].enableWEP:0 authTypeFlags is 1 ,encrTypeFlags is 1 ,m_nwKey is , key len is 0 ssid is Belkin_N_Wireless_489DD7 S, c67 E, e67 RegistrarSM constructor [24]pthread_cond_init: 4 [24]pthread_mutex_init: resource No. 43 [24]pthread_mutex_init: resource No. 44 [PORTABLITY]:WscCreateThread-------------------- [24]pthread_mutex_init: resource No. 45 [PORTABLITY]:pthread_mutex_init-------------------- RegistrarSM constructor [24]pthread_cond_init: 5 [24]pthread_mutex_init: resource No. 46 [24]pthread_mutex_init: resource No. 47 [PORTABLITY]:WscCreateThread-------------------- c_devPwd:org:84882295 **************mcp_devPwd:84882295;; Generated devPwd: ▒g▒ in startMonitor.... CInbEap Construction Sizeof(WSC_NOTIFY_DATA) = -2140694200 ---test--sizeof(WSC_NOTIFY_DATA) = 36 [24]pthread_cond_init: 6 [PORTABLITY]:WscCreateEvent-------------------- Entered udp_open Socket open successful, sd: -2140694216 Entered udp_open Socket open successful, sd: -2140694216 Entered udp_bind Binding successful for socket [-2140694232] [PORTABLITY]:WscCreateThread-------------------- In CInbEap::StaticRecvThread CInbEap::ActualRecvThread Started Entered udp_read in startMonitor.... CInbUPnPDev Construction Entered udp_open Socket open successful, sd: -2140694216 Entered udp_open Socket open successful, sd: -2140694216 Entered udp_bind Binding successful for socket [-2140694232] CInbUPnPDev StartMonitor [PORTABLITY]:WscCreateThread-------------------- MC::SwitchModeOn: Exit In CInbUPnPDev::StaticUPnPThread end UPnPCreateMicroStack Entered udp_read MC::StartStack: Informing app of mode -WscCmd::CallbackProc Enqueue done MC::SwitchModeOn: Done callback exit wscmain @@[31]pthread_mutex_unlock: the res is free 34-- -2143990900 WscCmd:ActualCBThreadProc: CB_MAIN_PUSH_MODE recd ******* MODE: Access Point ******* -@@[28]pthread_mutex_unlock: the res is free 36-- -2141841168 *******p_header->eType:1 Options: 0. Quit 1. Get configured 2. Get configured via push-button 3. Get configured using IEs Enter selection: ***gp_mc->mp_info->GetSwitchMode():1 mp_info->GetSwitchMode():1:e_currMode:1,,e_targetMode:3 mp_deviceInfo->authTypeFlags:1 mp_deviceInfo->encrTypeFlags:1 ********cp_devPwd:84882295***** mp_deviceInfo->authTypeFlags:1 mp_deviceInfo->encrTypeFlags:1 MC::SetBeaconIE: call to trans->SetBeaconIE() ok MC::SetProbeRespIE: call to trans->SetProbeRespIE() ok Waiting for Registrar to connect... WscCmd::unconfig initiated ActualUIThreadProc: wait q [reset_802dot1x] wireless module ready [init_wpa] dot1x_ready[0]=1 [reset_802dot1x] 802.1Xv2 ready