Alcatel-Lucent G-011G-P

From TechInfoDepot
Jump to navigationJump to search
Optical Network Terminal
G-011G-P.png
WikiDevi.wi-cat.ru
3rd Party Firmware
dd-wrt
Status Unknown
OpenWrt
Status Unknown
Tomato any flavor
Status Unknown
Platform
BrandModelRev
Alcatel-Lucent G-011G-P
Type
fiber gateway, ONT
CPU1 checkY
Broadcom BCM68385
CPU1 Type
MIPS 74K
CPU1 Speed
not specified ( 2 cores )
Flash1 Chip
Toshiba TN58NVG0S3ETA00
Flash1 Size
256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />
RAM1 Size
128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM1 Chip
Winbond W631GG6KB-15
ETH chip1
Broadcom BCM68385
Ethernet Port Count
1-1GbE-LAN
Wired Standard
IEEE 802.3i/3u/3ab
Expansion IF types
none specified
Power
12 VDC, 1 A
Connector type
barrel
Serial Port (UART)
yes, 4-pin header, 3.3V TTL, (115200 8N1), X2

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.

Links of Interest

Models

  • Alcatel-Lucent G-011G-P
  • Alcatel-Lucent I-011G-P
  • Alcatel-Nokia G-010G-Q/R
  • Alcatel-Nokia XS-010X-Q

JTAG-Serial Info

Serial

Boot log

bootlog • >>
CFEROM --> CFERAM0 --> HERE
************************************************************
*                                                          *
*                 Bootloader For Bcm9638x                  *
*                                                          *
************************************************************
Version      : V9.09.20
Buile Date   : Oct 24 2014-11:12:05
CPU          : Soc(68385_B0) MIPS32(240Mhz) DDR(333Mhz) Bus(240Mhz) RDP(400Mhz)
DRAM         : 128 MB
NAND         : 128 MB 4Bits Ecc
DEVxID       : 0x00a20101
Usrinfo      : 0x00a20101
Hit password to stop autoboot @ 3 ��2 ��1 
loading image..
ImageB crc checking
### CRAMFS loading 'vmlinux.lz' from imageb to 0x82800000
### CRAMFS load complete: 1143677 bytes loaded to 0x82800000
Entry at 0x8026ea90
Closing network.
Starting program at 0x8026ea90
Linux version 3.4.11-rt19+ (junjie@GPONBUSW1) (gcc version 4.6.2 (Buildroot 2011.11) ) #1 SMP PREEMPT Wed Feb 11 10:54:08 CST 2015


*** Voice Board id is not initialized properly ***


968385GSP prom init

CPU revision is: 0002a080 (Broadcom BMIPS4350)

Determined physical RAM map:

 memory: 01400000 @ 06c00000 (reserved)

 memory: 00400000 @ 06800000 (reserved)

 memory: 06800000 @ 00000000 (usable)

Zone PFN ranges:

  DMA      0x00000000 -> 0x00001000

  Normal   0x00001000 -> 0x00006800

Movable zone start PFN for each node

Early memory PFN ranges

    0: 0x00000000 -> 0x00006800

On node 0 totalpages: 26624

free_area_init_node: node 0, pgdat 8031f940, node_mem_map 81000000

  DMA zone: 32 pages used for memmap

  DMA zone: 0 pages reserved

  DMA zone: 4064 pages, LIFO batch:0

  Normal zone: 176 pages used for memmap

  Normal zone: 22352 pages, LIFO batch:3

PERCPU: Embedded 7 pages/cpu @810d3000 s5088 r8192 d15392 u32768

pcpu-alloc: s5088 r8192 d15392 u32768 alloc=8*4096

pcpu-alloc: [0] 0 [0] 1 

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 26416

Kernel command line: ro noinitrd  irqaffinity=0

PID hash table entries: 512 (order: -1, 2048 bytes)

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.

Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes

Memory: 101864k/106496k available (2460k kernel code, 4632k reserved, 676k data, 176k init, 0k highmem)

Preemptible hierarchical RCU implementation.

NR_IRQS:256

console [ttyS0] enabled

Allocating memory for DSP module core and initialization code

Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0

Calibrating delay loop... 237.05 BogoMIPS (lpj=118528)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512

--Kernel Config--

  SMP=1

  PREEMPT=1

  DEBUG_SPINLOCK=0

  DEBUG_MUTEXES=0

Broadcom Logger v0.1 Feb 11 2015 10:49:26

CPU revision is: 0002a080 (Broadcom BMIPS4350)

Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.

Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes

Brought up 2 CPUs

NET: Registered protocol family 16

PMC Driver Init... done.

bio: create slab <bio-0> at 0

bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated

skbFreeTask created successfully

�[0;34mBLOG v3.0 Initialized�[0m

BLOG Rule v1.0 Initialized

Broadcom IQoS v0.1 Feb 11 2015 10:52:47 initialized

Switching to clocksource MIPS

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 4096 (order: 3, 32768 bytes)

TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

TCP: reno registered

UDP hash table entries: 128 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)

NET: Registered protocol family 1

init_bcm_tstamp: unhandled mips_hpt_freq=120000000, adjust constants in bcm_tstamp.c

bcm_tstamp initialized, (hpt_freq=120000000 2us_div=120 2ns_mult=0 2ns_shift=0)

jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.

msgmni has been set to 198

io scheduler noop registered (default)

Broadcom NAND controller (BrcmNand Controller)

mtd->oobsize=0, mtd->eccOobSize=0

NAND_CS_NAND_XOR=00000000

B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0

brcmnand_read_id: CS0: dev_id=98d19015

After: NandSelect=40000001, nandConfig=15142200

brcmnand_probe: Ecc level set to 1, sectorSize=512 from ID table

Block size=00020000, erase shift=17

NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11

busWidth=1, pageSize=2 GiBB, page_shift=11, page_mask=000007ff

timing1 not adjusted: 6574845b

timing2 not adjusted: 00001e96

BrcmNAND mfg 98 d1 TOSHIBA TC58NVG0S3ETA00 128MB on CS0


Found NAND on CS0: ACC=f7441010, cfg=15142200, flashId=98d19015, tim1=6574845b, tim2=00001e96

BrcmNAND version = 0x80000500 128MB @00000000

brcmnand_scan: B4 nand_select = 40000001

brcmnand_scan: After nand_select = 40000001

handle_acc_control: default CORR ERR threshold  1 bits

ACC: 16 OOB bytes per 512B ECC step; from ID probe: 16

page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17

Brcm NAND controller version = 5.0 NAND flash size 128MB @18000000

ECC layout=brcmnand_oob_bch4_2k

brcmnand_scan:  mtd->oobsize=64

brcmnand_scan: oobavail=35, eccsize=512, writesize=2 GiB

brcmnand_scan, eccsize=512, writesize=2 GiB, eccsteps=4, ecclevel=4, eccbytes=7

-->brcmnand_default_bbt

brcmnand_default_bbt: bbt_td = bbt_slc_bch4_main_descr

Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0

Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0

brcmnand_reset_corr_threshold: default CORR ERR threshold  1 bits for CS0

brcmnand_reset_corr_threshold: CORR ERR threshold changed to 3 bits for CS0

brcmnandCET: Status -> Deferred

Creating 11 MTD partitions on "brcmnand.0":

0x000000000000-0x000000100000 : "boota"

0x000000100000-0x000000200000 : "bootb"

0x000000200000-0x000000400000 : "configa"

0x000000400000-0x000000600000 : "configb"

0x000000600000-0x000002200000 : "imagea"

0x000002200000-0x000003000000 : "imagec0"

0x000003000000-0x000004c00000 : "imageb"

0x000004c00000-0x000005a00000 : "imagec1"

0x000005a00000-0x000005b00000 : "misca"

0x000005b00000-0x000005c00000 : "miscb"

0x000005c00000-0x000008000000 : "reserved"

i2c /dev entries driver

brcmboard: brcm_board_init entry

#### g_product_id=0x00a20101 g_flag_5srst=0x00000000####

Alloc watchdog timer 2

Serial: BCM63XX driver $Revision: 3.00 $

�[0;33mMagic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)�[0m

ttyS0 at MMIO 0xb4e00500 (irq = 9) is a BCM63XX

ttyS1 at MMIO 0xb4e00520 (irq = 10) is a BCM63XX

TCP: cubic registered

NET: Registered protocol family 17

Initializing MCPD Module

Ebtables v2.0 registered

ebt_time registered

ebt_ftos registered

8021q: 802.1Q VLAN Support v1.8

VFS: Mounted root (cramfs filesystem) readonly on device 31:6.

Freeing unused kernel memory: 176k freed


init started: BusyBox v1.9.2 (2014-01-06 10:43:27 CST)
tar: chdir(/dev/shm): No such file or directory
grep: /etc/network/options: No such file or directory

grep: /etc/network/options: No such file or directory
grep: /etc/network/options: No such file or directory
jffs2: Empty flash at 0x0001300c ends at 0x00013800

 #mount /dev/mtdblock2 -->  /mnt/rwdir ok 
# num is 10,nothing need to do
cp: cannot stat '/etc/resolv.conf.rwdir': No such file or directory
cat: can't open '/dev/rgs_logger': No such file or directory
ifconfig: SIOCGIFFLAGS: No such device
# Created object <system>

RDPA lan init
# Created object <port/index=lan0>

# Created object <egress_tm/dir=ds,index=0>

# Created object <bridge/index=0>

RDPA lan init end
rdpa filter init start!!
# Created object <filter>

rdpa filter init end
ONT>SSP: Set rlimit: S = 0x100000, H = 0x7fffffff
TMR: Set rlimit: S = 0x100000, H = 0x7fffffff
Starting Application: 0x00002000, /bin/TimerMgr................Done. elapsed time:(227)ms

Update timer: curTime=0000319b, gTmrTimerMsCounter=00000000
LOG: Set rlimit: S = 0x100000, H = 0x7fffffff
Starting Application: 0x00001000, /bin/LogMgr................Done. elapsed time:(123)ms
MMR: Set rlimit: S = 0x100000, H = 0x7fffffff
actImage[1], PartId[6], custom[UUAL] sys_cfg[/etc/sys.cfg.alu]
cp: cannot stat '/etc/sys.cfg.alu': No such file or directory
Starting Application: 0x00007000, /bin/MiscMgr................Done. elapsed time:(625)ms
d6885a:Exit SSP -->log, msg 0x4000c,elapsed time:706 ms
Mount Backup[/dev/mtdblock4] as cramfs...Success.
major ID[0xa2] minor ID[0x1]
PMR: Set rlimit: S = 0x100000, H = 0x7fffffff
Starting Application: 0x00004000, /bin/PonMgr................Done. elapsed time:(344)ms
NET: Set rlimit: S = 0x100000, H = 0x7fffffff
sh: can't open /sbin/ath_wifi.sh
Starting Application: 0x00009000, /bin/NetMgr................Done. elapsed time:(475)ms
EMR: Set rlimit: S = 0x100000, H = 0x7fffffff
Starting Application: 0x00005000, /bin/EthMgr................Done. elapsed time:(387)ms
MEC: Set rlimit: S = 0x100000, H = 0x7fffffff
Starting Application: 0x00003000, /bin/MecMgr................Done. elapsed time:(3854)ms
15f33db:Exit SSP -->ssp, msg 0x50000,elapsed time:10711 ms
16b9c4b:Exit MEC -->pmr, msg 0xc0002,elapsed time:804 ms
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device

9107ca7 9107ca7 9107ca7
ifconfig: SIOCGIFFLAGS: No such device
184f1c9:Exit MEC -->net, msg 0xc0002,elapsed time:1653 ms
192bb33:Exit MEC -->emr, msg 0xc0002,elapsed time:898 ms
Powered down 
1a7333e:Exit MEC -->emr, msg 0xc0004,elapsed time:1258 ms
i/f name: brdg 
gem ids: 

INFO: ALL APPs are ready.
1a9514a:Exit NET -->mec, msg 0xc0000,elapsed time:4858 ms
start config net connection for WAN[0]