ASUS RT-AC87U

abgn+ac (AC2400)
	Dual-band Wireless-AC2400 Gigabit Router
Homepage	Product page (RT-AC87U) Product page (RT-AC87R)
Wikipedia	Asus routers
WikiDevi.wi-cat.ru	ASUS RT-AC87U
3rd Party Firmware
dd-wrt	Supported
OpenWrt	Partial Support
Tomato any flavor	Status Unknown
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	ASUS RT-AC87U
FCC ID	MSQ-RTAC87U
IC ID	3568A-RTAC87U
Type	wireless router
CPU1	Broadcom BCM4709A0
CPU1 Type	ARMv7 Cortex-A9
CPU1 Speed	1.0 GHz ( 2 cores )
CPU2	Quantenna QT3840BC
CPU2 Type	ARC 700
CPU2 Speed	500 MHz ( 2 cores )
Flash1 Chip	Spansion S34ML01G100TFI00
Flash1 Size	128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
Flash2 Chip	Winbond W25X05CL
Flash2 Size	0.065 MiB68,157.44 B <br />532.48 Kib <br />66.56 KiB <br />0.52 Mib <br />6.347656e-5 GiB <br />
RAM1 Size	256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />
RAM1 Chip	ESMT M15F2G16128A-BDB
RAM2 Size	128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM2 Chip	ESMT M15F1G1664A-ADB
ETH chip1	Broadcom BCM4709A0
ETH chip2	Realtek RTL8211E
Switch	Broadcom BCM4709A0
Ethernet Port Count	1-1GbE-WAN 4-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
	802dot11 OUI: 10:C3:7B (2 E, 2 W), 78:24:AF; Ethernet OUI: 10:C3:7B (2 E, 2 W), 78:24:AF
Stock bootloader	CFE 6.37 U-Boot v36.5
Stock FW OS	Linux 2.6.35
Expansion IF types	USB 2.0, USB 3.0
USB ports	2
USB Hub Compatible	Untested
Power	19 VDC, 2.37 A
Connector type	barrel
Serial Port (UART)	yes, 4-pin header
	Flags:; Wave2, AiCloud support
	Additional chips; 2.4GHz Power Amplifier IC;Richwave;RTC6649E;;3;; 5GHz Power Amplifier IC;Skyworks;SKY85402-11;SKY, 85402, 11;3;
Other
	Default SSID: ASUS (100 addl. devices); , ASUS_5G (46 addl. devices); Default IP address: 192.168.1.1; the IP 192.168.1.1 is used by 1324 additional devices; of which 173 are ASUS devices; Default login user: admin; Default login password: admin; admin:admin credentials used by 1342 additional devices; of which 207 are ASUS devices
Manuf/OEM/ODM	Arcadyan WG9117A AC44-ASU
3rd Party Firmware Support	AsusWRT-Merlin • (Wiki \| List); , DD-WRT • (List); , OpenWrt • (List \| Dev \| DLs);
Retail
Availability	common
FCC approval date	30 June 2014
Newegg	9SIADXX5TA3027
ASIN	B00MPI5N7U
Country of manuf	China
Radio 1
Chip1	Quantenna QT3840BC
Chip2	Quantenna QT2518B
Wireless interface OUI	10:C3:7B, 78:24:AF
Antenna Connector Type	U.FL, RP-SMA
MIMO status	4x4:4
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 1733 Mbps
802.11n	up to 600 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
Radio 2
Chip1	Broadcom BCM4360
Wireless interface OUI	10:C3:7B, 78:24:AF
Antenna Connector Type	U.FL, RP-SMA
MIMO status	3x3:3
Wireless Standard	IEEE 802.11b/g/n
N-QAM	up to 600 Mbps
802.11n	up to 450 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio cor_rev	40

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.
For a list of all currently documented Quantenna chipsets with specifications, see Quantenna.
For a list of all currently documented Realtek chipsets with specifications, see Realtek.

For a list of all currently documented ASUS device with specifications, see ASUS.

• 1733 Mbps - 4SS 5GHz 802.11ac (80MHz chan.),

• 600 Mbps - 4SS 2.4GHz 802.11n (40MHz chan.) = AC2400 class

Overview

This device was under short-term confidentiality, but that expired 12/24/2014 ⚠.

Wi-Fi Certified : WFA55415 (as of 06/30/2014)

The manufacturer stated in FCC test report is Compal (Compal Networking

[KunShan]), a part of Arcadyan - same manuf. noted for ASUS RT-AC56U

(WG9117GAC). See also ASUS EA-AC87 (Arcadyan WA5005AAC44-ASU)..

The primary SoC for device is Broadcom BCM4709 (ARM Cortex-A9 DualCore @1 GHz).

The 2.4GHz radio is implemented with BCM4360, connected via PCIe to BCM4709.

The 5GHz radio is contained w/ independent Quantenna chipset (QT3840BC+QT2518B),

(QSR1000, ARC 700 core), which is connected in some fashion (RGMII) to BCM4709.

Links of Interest

Reviews

Asus RT-AC87U - First look @ SmallNetBuilder

10:C3:7B OUI on the pics shown

PSU: 19V 2.37A 45W Block diagram

Forum threads

RT-AC87U - the platform details @ the SmallNetBuilder forums (RMerlin)

"RT-AC87U REV 1.50" board shown, an Arcadyan typical label is found on board noted

as being BCM4709 (BCM4709A0) based. ARC 700 family core used w/ Quantenna SoC,

which seems to have also been used with at least some older Quantenna SoC's.

SoC's/radios are segmented - 2.4 GHz is handled on BCM4360 directly connected

to the BCM4709, while 5 GHz is handled on the independent Quantenna SoC.

The Quantenna firmware is contained within the main Flash and uploaded at boot.

Wave 2, AC2300

4x4 MU-MIMO 802.11ac

802.11n: 2.4 GHz (40MHz) 4T4R 600 Mbps

802.11ac: 5 GHz (80MHz) 4T4R 1700 Mbps

Flashing

NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power.

Flashing dd-wrt

Support started version: rt-ac87u build 25309 20141111
Current supported version: ?

Please insert instructions here

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki
On the OpenWrt Forum
Support started version: 15.05
Current supported version: 23.05.5
Unsupported Functions:
WiFi 2.4GHz partly, WiFi 5GHz

Please insert instructions here

JTAG-Serial Info

Serial

Broadcom boot log

Broadcom boot log • >>

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.09.28 17:29:30 =~=~=~=~=~=~=~=~=~=~=~=

Digital core power voltage set to 1.0V
Decompressing...done
Digital core power voltage set to 1.0V

SHMOO VER 1.13

PKID07DC06011801080000000000001A103F01000000

S300001B7
00001240

RDLYW0 00000004

RDENW0 00000029

RDQSW0 

    0000000000111111111122222222223333333333444444444455555555556666
    0123456789012345678901234567890123456789012345678901234567890123
 00 ------++++++++++++++++++++++++X+++++++++++++++++++++++----------
 01 ---------++++++++++++++++++++++++X++++++++++++++++++++++++------
 02 ----------+++++++++++++++++++++++++X++++++++++++++++++++++++----
 03 ---------+++++++++++++++++++++++X++++++++++++++++++++++---------
 04 -----+++++++++++++++++++++++X++++++++++++++++++++++-------------
 05 --------+++++++++++++++++++++++X+++++++++++++++++++++++---------
 06 --------+++++++++++++++++++++++X+++++++++++++++++++++++---------
 07 -------++++++++++++++++++++++++X+++++++++++++++++++++++---------
 08 ----++++++++++++++++++++++++X++++++++++++++++++++++++-----------
 09 ----+++++++++++++++++++++++++X++++++++++++++++++++++++----------
 10 -----+++++++++++++++++++++++++X++++++++++++++++++++++++---------
 11 --++++++++++++++++++++++++X++++++++++++++++++++++++-------------
 12 +-++++++++++++++++++++++++X+++++++++++++++++++++++--------------
 13 -++++++++++++++++++++++++X++++++++++++++++++++++++--------------
 14 --++++++++++++++++++++++++X+++++++++++++++++++++++--------------
 15 --+++++++++++++++++++++++X+++++++++++++++++++++++---------------


P   W0 

    0000000000111111111122222222223333333333444444444455555555556666
    0123456789012345678901234567890123456789012345678901234567890123
 00 ------++++++++++++++++++++++++X++++++++++++++++++++++++---------
 01 ---------+++++++++++++++++++++++++X++++++++++++++++++++++++-----
 02 -----------++++++++++++++++++++++++X+++++++++++++++++++++++-----
 03 ---------++++++++++++++++++++++++X++++++++++++++++++++++++------
 04 ------+++++++++++++++++++++++X+++++++++++++++++++++++-----------
 05 --------++++++++++++++++++++++++X+++++++++++++++++++++++--------
 06 --------++++++++++++++++++++++++X++++++++++++++++++++++++-------
 07 --------+++++++++++++++++++++++X+++++++++++++++++++++++---------
 08 ----+++++++++++++++++++++++++X++++++++++++++++++++++++----------
 09 ----+++++++++++++++++++++++++X++++++++++++++++++++++++----------
 10 -----+++++++++++++++++++++++++X++++++++++++++++++++++++---------
 11 ---+++++++++++++++++++++++++X++++++++++++++++++++++++-----------
 12 --+++++++++++++++++++++++++X++++++++++++++++++++++++------------
 13 -+++++++++++++++++++++++++X++++++++++++++++++++++++-------------
 14 --++++++++++++++++++++++++X+++++++++++++++++++++++--------------
 15 --++++++++++++++++++++++++X+++++++++++++++++++++++--------------


N   W0 

    0000000000111111111122222222223333333333444444444455555555556666
    0123456789012345678901234567890123456789012345678901234567890123
 00 ----+++++++++++++++++++++++++X++++++++++++++++++++++++----------
 01 ------++++++++++++++++++++++++++X+++++++++++++++++++++++++------
 02 --------+++++++++++++++++++++++++X+++++++++++++++++++++++++-----
 03 ------++++++++++++++++++++++++X++++++++++++++++++++++++---------
 04 ---++++++++++++++++++++++++X+++++++++++++++++++++++-------------
 05 ---++++++++++++++++++++++++++X+++++++++++++++++++++++++---------
 06 ------++++++++++++++++++++++++X++++++++++++++++++++++++---------
 07 ----+++++++++++++++++++++++++X++++++++++++++++++++++++----------
 08 --++++++++++++++++++++++++++X+++++++++++++++++++++++++----------
 09 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++----------
 10 ----+++++++++++++++++++++++++X+++++++++++++++++++++++++---------
 11 -+++++++++++++++++++++++++X++++++++++++++++++++++++-------------
 12 -++++++++++++++++++++++++X++++++++++++++++++++++++--------------
 13 +++++++++++++++++++++++++X++++++++++++++++++++++++--------------
 14 +++++++++++++++++++++++++X+++++++++++++++++++++++++-------------
 15 ++++++++++++++++++++++++X++++++++++++++++++++++++---------------


WRDQW0 

    0000000000111111111122222222223333333333444444444455555555556666
    0123456789012345678901234567890123456789012345678901234567890123
 00 ++++++++++++++++++++X++++++++++++++++++++----------++++++++++++-
 01 ++++++++++++++++++++++X+++++++++++++++++++++--------+++++++++++-
 02 ++++++++++++++++++++++X++++++++++++++++++++++------++++++++++++-
 03 +++++++++++++++++++++X+++++++++++++++++++++--------++++++++++++-
 04 +++++++++++++++++++X+++++++++++++++++++-----------+++++++++++++-
 05 ++++++++++++++++++++X++++++++++++++++++++----------++++++++++++-
 06 +++++++++++++++++++++X++++++++++++++++++++---------++++++++++++-
 07 ++++++++++++++++++++X++++++++++++++++++++----------++++++++++++-
 08 +++++++++++++++++++X+++++++++++++++++++------------++++++++++++-
 09 +++++++++++++++++++++X++++++++++++++++++++---------++++++++++++-
 10 +++++++++++++++++++++X++++++++++++++++++++---------++++++++++++-
 11 ++++++++++++++++++++X+++++++++++++++++++-----------++++++++++++-
 12 +++++++++++++++++++X++++++++++++++++++-------------++++++++++++-
 13 +++++++++++++++++++X++++++++++++++++++-------------++++++++++++-
 14 ++++++++++++++++++++X+++++++++++++++++++-----------++++++++++++-
 15 +++++++++++++++++++X++++++++++++++++++-------------++++++++++++-


WRDMW0 00000020
WRDMW0 00000019


ADDR

    0000000000111111111122222222223333333333444444444455555555556666
    0123456789012345678901234567890123456789012345678901234567890123
 00 ++++++++++++++++++S++++++++++++X++++++++++++++++++++++++++++++++

Decompressing...done
Detect CPU turbo button... 

CFE version 6.37.14.86 (r456083) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: 4 22 16:05:16 CST 2014 (raymonddev@raymonddev-vm1210)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1000,*800*
et1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.86 (r456083)
CPU type 0x0: 1000MHz
Tot mem: 262144 KBytes

CFE mem:    0x00F00000 - 0x01795558 (9000280)
Data:       0x00F4DBB4 - 0x00F4E080 (1228)
BSS:        0x00F4E090 - 0x00F93558 (283848)
Heap:       0x00F93558 - 0x01793558 (8388608)
Stack:      0x01793558 - 0x01795558 (8192)
Text:       0x00F00000 - 0x00F4430C (279308)

Device eth0:  hwaddr 78-24-AF-93-AF-F0, ipaddr 192.168.12.1, mask 255.255.255.0
        gateway not set, nameserver not set
Null Rescue Flag.
boot the image...
go load
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: TFTP Server.
..tftp retry wait 0
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: .... 4009856 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
brd: module loaded
loop: module loaded
pflash: found no supported devices
bcmsflash: found no supported devices
Boot partition size = 524288(0x80000)
lookup_nflash_rootfs_offset: offset = 0x200000
nflash: squash filesystem with lzma found at block 28
Creating 4 MTD partitions on "nflash":
0x000000000000-0x000000080000 : "boot"
0x000000080000-0x000000200000 : "nvram"
0x000000200000-0x000004000000 : "linux"
0x000000399330-0x000004000000 : "rootfs"
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
=== PPTP init ===
u32 classifier
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3992 buckets, 15968 max)
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Registering the dns_resolver key type
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD NAND 128MiB 3,3V 8-bit)
Spare area=64 eccbytes 56, ecc bytes located at:
 2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 
34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63
Available 7 bytes at (off,len):
(1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0) 
Scanning device for bad blocks
Options: NO_AUTOINCR,NO_READRDY,BBT_SCAN2NDPAGE,
Creating 2 MTD partitions on "brcmnand":
0x000004000000-0x000007ec0000 : "brcmnand"
0x000007ec0000-0x000008000000 : "asus"
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
devtmpfs: mounted
Freeing init memory: 212K
## mknod /dev/null: File exists
## mknod /dev/console: File exists
set_action 0

Hit ENTER for console...

firmware version: 3.0.0.4.376.47_0
[1 preinit:init_nvram +7] init_nvram for 30
wan_proto:pppoe not support FA mode...
num_of_mssid_support(0x0092): [mssid] support [3] mssid
wan_proto:pppoe not support FA mode...

FA off.
ctf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x1
et_module_init: et_txq_thresh set to 0x400
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.86 (r456083)
hotplug net INTERFACE=eth0 ACTION=add
wl_module_init: passivemode set to 0x0
wl_module_init: txworkq set to 0x1
eth1: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.86 (r456083)
hotplug net INTERFACE=eth1 ACTION=add
/ # check_action 0
start jffs2: 4, 65798144
[1 preinit:init_main +12] main loop signal/state=12
start_logger:
start_usb
no tune_bdflush
ready to modprobe usb3/xhci
xhci_hcd 0000:00:0c.0: Failed to enable MSI-X
xhci_hcd 0000:00:0c.0: failed to allocate MSI entry
usb usb1: No SuperSpeed endpoint companion for config 1  
interface 0 altsetting 0 ep 129: using minimum values
_ifconfig: name=eth0 flags=1043 IFUP addr=(null) netmask=(null)
hotplug net INTERFACE=vlan1 ACTION=add
hotplug net INTERFACE=vlan2 ACTION=add
start_lan 1267
update_lan_state(lan_, 0, 0)
update_lan_state(workaround to infosvr)
generate_wl_para(0x0e00): unit 0 subunit -1
num_of_mssid_support(0x0092): [mssid] support [3] mssid
generate_wl_para(0x109b): bw: 0
generate_wl_para(0x109d): chanspec: 6l
generate_wl_para(0x109e): bw_cap: 3
generate_wl_para(0x10a4): obss_coex: 1
wlconf_pre(0x02f6): set vhtmode 1
generate_wl_para(0x0e00): unit 1 subunit -1
num_of_mssid_support(0x0092): [mssid] support [3] mssid
chanspec_fix(0x0796): unit: 1, bw_cap: 7, chanspec: 149/80
generate_wl_para(0x109b): bw: 3
generate_wl_para(0x109d): chanspec: 149/80
generate_wl_para(0x109e): bw_cap: 7
generate_wl_para(0x10a4): obss_coex: 0
set_wltxpower(0x08c1): unit: 0, txpower: 100
wltxpower_rtac87u(0x082f): [100][0:]
wltxpower_rtac87u(0x0838): txpoewr between: min:[76] to max:[100]
setpoweroffset_rtac87u(0x00c6): [3][0:]
setpoweroffset_rtac87u(0x00cc): [rc] [0:maxp2ga0]=[0x6A]
setpoweroffset_rtac87u(0x00d0): [rc] [0:maxp2ga1]=[0x6A]
setpoweroffset_rtac87u(0x00d4): [rc] [0:maxp2ga2]=[0x6A]
start_lan: setting up the bridge br0
vlan1: cmd=14: Operation not supported
_ifconfig: name=vlan1 flags=1043 IFUP addr=(null) netmask=(null)
start_lan: setting MAC of br0 bridge to 78:24:AF:93:AF:F0
_ifconfig: name=eth1 flags=1043 IFUP addr=(null) netmask=(null)
hotplug net INTERFACE=br0 ACTION=add
generate_wl_para(0x0e00): unit 0 subunit -1
num_of_mssid_support(0x0092): [mssid] support [3] mssid
generate_wl_para(0x109b): bw: 0
generate_wl_para(0x109d): chanspec: 6l
generate_wl_para(0x109e): bw_cap: 3
generate_wl_para(0x10a4): obss_coex: 1
generate_wl_para(0x0e00): unit 0 subunit 1
generate_wl_para(0x0e00): unit 0 subunit 2
generate_wl_para(0x0e00): unit 0 subunit 3

wifi0: cmd=14: No such device
_ifconfig: name=wifi0 flags=1043 IFUP addr=(null) netmask=(null)
wifi0: No such device
generate_wl_para(0x0e00): unit 1 subunit -1
num_of_mssid_support(0x0092): [mssid] support [3] mssid
chanspec_fix(0x0796): unit: 1, bw_cap: 7, chanspec: 149/80
generate_wl_para(0x109b): bw: 3
generate_wl_para(0x109d): chanspec: 149/80
generate_wl_para(0x109e): bw_cap: 7
generate_wl_para(0x10a4): obss_coex: 0
generate_wl_para(0x0e00): unit 1 subunit 1
generate_wl_para(0x0e00): unit 1 subunit 2
generate_wl_para(0x0e00): unit 1 subunit 3
_ifconfig: name=br0 flags=1043 IFUP addr=192.168.12.1 netmask=255.255.255.0
_ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
update_lan_state(lan_, 2, 0)
update_lan_state(workaround to infosvr)

set default filter settings
stop_nat_rules: apply the redirect_rules!
start_lan 1714
[stateless] channel:[149]
[stateless] bw:[3]
get_tx_power_qtn(0x02f8): txpoewr between: min:[76] to max:[100]
# wanduck: nvram changed: Don't enable the USB line!
# wanduck: nvram changed: x_Setting=1, link_modem=0.
# wanduck: Got LAN(-1) information:

# Enable direct rule
start_services 3491
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: COEX: downgraded chanspec 0x1808 to 0x1006: channel 3 used by exiting BSSs 
acsd: selected channel spec: 0x1006 (6)
acsd: Adjusted channel spec: 0x1006 (6)
acsd: selected DFS-exit channel spec: 0x1006 (6)
acsd: COEX: downgraded chanspec 0x1808 to 0x1006: channel 3 used by exiting BSSs 
acsd: selected channel spec: 0x1006 (6)
acsd: Adjusted channel spec: 0x1006 (6)
acsd: selected channel spec: 0x1006 (6)
[1 preinit:start_dnsmasq +27] begin
[1 preinit:stop_dnsmasq +27] begin
[1 preinit:stop_dnsmasq +27] end
[1 preinit:start_dnsmasq +27] end
start_lan_port(0) 1
start_pptpd: getpid= 1
open options file
check if wan_wins = zero
write config
TZ watchdog
start_pptpd: ret= 0

gro enabled with interval 2
decomp: fname=/var/lib/misc/rstats-speed.gz
decomp: gzip -dc /var/lib/misc/rstats-speed.gz > /var/tmp/rstats-uncomp != 0
load: speed_count = 0
load: read source= save_path=
load_history: fname=/var/lib/misc/rstats-history.gz
decomp: fname=/var/lib/misc/rstats-history.gz
[bwdpi check] starting...
decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0
decomp: fname=/var/lib/misc/rstats-history.gz
disk_monitor: starting...
disk_monitor: day=1, week=6, time=4:0.
disk_monitor: decide if scan the target...
disk_monitor: 0: wait_second=68400...
disk_monitor: 1: wait_second=68400...
disk_monitor: wait_second=68400...
disk_monitor: Pause...

decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0
load_history: load failed
start_samba: cmd=smbpasswd "*****" "******".
Script: running /jffs/scripts/services-start (args: (null))
vlan1: cmd=14: Operation not supported
wifi0: cmd=14: No such device
ATE command error
start_wan: start_wan_if(0)!
start_wan_if(0)
update_wan_state(wan0_, 0, 0)
convert_wan_nvram(wan0_)
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=0.0.0.0
eth0: Cannot assign requested address
rpc_qcsapi_init(0x0045): #1 attempt to create RPC connection
zcip_wan:: init
start_pppd: unit=0.
update_wan_state(wan0_, 1, 0)
start_wan_if(): End.
start_wan: start_wan_if(1)!
start_wan_if(1)
update_wan_state(wan1_, 0, 0)
start_wan_if(): Cound't find the type(0) of unit(1)!!!
start_wan_if(): End.
sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
U2EC starting ...
hotplug net INTERFACE=ppp0 ACTION=add
169.254.39.75: RPC: Port mapper failure - RPC: Unable to receive
ippreup_main():: /tmp/ppp/ip-pre-up
ippreup_main: unit=0 ifname=ppp0
ippreup_main:: done
ipup_main():: /tmp/ppp/ip-up
ipup_main: unit=0 ifname=ppp0
_ifconfig: name=ppp0 flags=1043 IFUP addr=0.0.0.0 netmask=(null)
_ifconfig: name=ppp0 flags=1043 IFUP addr=31.207.64.12 netmask=255.255.255.255
wan_up(ppp0)
update_wan_state(wan0_, 2, 0)
ip-up 676:notify_rc: start_firewall
[wan up] do dpi engine start
ip-up 676:notify_rc: stop_upnp
676: wait for previous script(29/30): start_firewall 676 ip-up.
rpc_qcsapi_init(0x0045): #2 attempt to create RPC connection
676: wait for previous script(28/30): start_firewall 676 ip-up.

# Disable direct rule if not tunnelled (D2C)
start_nat_rules: apply the nat_rules(/tmp/nat_rules)!
[539 wanduck:start_dnsmasq +35] begin
[539 wanduck:stop_dnsmasq +35] begin
[539 wanduck:stop_dnsmasq +35] end
[539 wanduck:start_dnsmasq +35] end
676: wait for previous script(27/30): start_firewall 676 ip-up.
676: wait for previous script(26/30): start_firewall 676 ip-up.
169.254.39.75: RPC: Port mapper failure - RPC: Unable to receive
676: wait for previous script(25/30): start_firewall 676 ip-up.
rpc_qcsapi_init(0x0045): #3 attempt to create RPC connection
676: wait for previous script(24/30): start_firewall 676 ip-up.
676: wait for previous script(23/30): start_firewall 676 ip-up.
676: wait for previous script(22/30): start_firewall 676 ip-up.
169.254.39.75: RPC: Port mapper failure - RPC: Unable to receive
zcip_wan:: config
_ifconfig: name=eth0 flags=1043 IFUP addr=0.0.0.0 netmask=(null)
_ifconfig: name=eth0 flags=1043 IFUP addr=169.254.182.150 netmask=255.255.0.0
wan_up(eth0)
zcip 723:notify_rc: start_firewall
723: wait for previous script(29/30): start_firewall 676 ip-up.
676: wait for previous script(21/30): start_firewall 676 ip-up.
rpc_qcsapi_init(0x0045): #4 attempt to create RPC connection
723: wait for previous script(28/30): start_firewall 676 ip-up.
676: wait for previous script(20/30): start_firewall 676 ip-up.
723: wait for previous script(27/30): start_firewall 676 ip-up.
676: wait for previous script(19/30): start_firewall 676 ip-up.
723: wait for previous script(26/30): start_firewall 676 ip-up.
676: wait for previous script(18/30): start_firewall 676 ip-up.
169.254.39.75: RPC: Port mapper failure - RPC: Unable to receive
723: wait for previous script(25/30): start_firewall 676 ip-up.
676: wait for previous script(17/30): start_firewall 676 ip-up.
rpc_qcsapi_init(0x0045): #5 attempt to create RPC connection
723: wait for previous script(24/30): start_firewall 676 ip-up.
676: wait for previous script(16/30): start_firewall 676 ip-up.
723: wait for previous script(23/30): start_firewall 676 ip-up.
676: wait for previous script(15/30): start_firewall 676 ip-up.
723: wait for previous script(22/30): start_firewall 676 ip-up.
676: wait for previous script(14/30): start_firewall 676 ip-up.
169.254.39.75: RPC: Port mapper failure - RPC: Unable to receive
723: wait for previous script(21/30): start_firewall 676 ip-up.
676: wait for previous script(13/30): start_firewall 676 ip-up.
rpc_qcsapi_init(0x0045): #6 attempt to create RPC connection
723: wait for previous script(20/30): start_firewall 676 ip-up.
676: wait for previous script(12/30): start_firewall 676 ip-up.
723: wait for previous script(19/30): start_firewall 676 ip-up.
676: wait for previous script(11/30): start_firewall 676 ip-up.
723: wait for previous script(18/30): start_firewall 676 ip-up.
676: wait for previous script(10/30): start_firewall 676 ip-up.
169.254.39.75: RPC: Port mapper failure - RPC: Unable to receive
723: wait for previous script(17/30): start_firewall 676 ip-up.
676: wait for previous script(9/30): start_firewall 676 ip-up.
rpc_qcsapi_init(0x0045): #7 attempt to create RPC connection
qtn_monitor_main(0x00c7): Qcsapi qcsapi init takes 24 seconds
qtn_monitor_main(0x00c9): defer lanport_ctrl(1)
2nd jffs2: asus
Mount 2nd jffs2...
check_action 0
2nd jffs2: 5, 1310720
[1 preinit:init_main +54] main loop signal/state=10
cmd[0]=start_firewall
[1 preinit:handle_notifications +54] running: 2 firewall

set default filter settings
723: wait for previous script(16/30): start_firewall 676 ip-up.
check_2nd_jffs(0x03f9): umount asus_jffs ok
qtn_monitor_main(0x00dd): [***] rpc_parse_nvram_from_httpd
writting prerouting ppp0 31.207.64.12 eth0 169.254.182.150 br0 192.168.12.1
wanport_status(0) 1
start_nat_rules: apply the nat_rules(/tmp/nat_rules_ppp0_eth0)!
rpc_qcsapi_set_SSID(0x0090): wifi0 as: ******
rpc_qcsapi_set_SSID_broadcast(0x00a2): wifi0 as: TRUE
[1 preinit:start_dnsmasq +55] begin
[1 preinit:stop_dnsmasq +55] begin
676: wait for previous script(8/30): start_firewall 676 ip-up.
[1 preinit:stop_dnsmasq +55] end
rpc_qcsapi_set_vht(0x00be): wifi0 as: 11ac
[1 preinit:start_dnsmasq +55] end
[1 preinit:filter_setting +55] writing vts_enable_x
[1 preinit:filter_setting +55] write porttrigger
[1 preinit:filter_setting +55] write wl filter
[1 preinit:filter_setting +55] write url filter
723: wait for previnf_conntrack_rtsp v0.6.21 loading
ous script(15/30): start_firewall 676 ip-up.
nf_nat_rtsp v0.6.21 loading
handle_notifications() end
[1 preinit:init_main +56] main loop signal/state=14
ip-up 676:notify_rc: start_upnp
676: wait for previous script(29/30): stop_upnp 676 ip-up.
[1 preinit:init_main +56] main loop signal/state=10
cmd[0]=stop_upnp
[1 preinit:handle_notifications +56] running: 1 upnp
killall_tk: waiting name=miniupnpd n=9
handle_notifications() end
[1 preinit:init_main +56] main loop signal/state=14
rpc_qcsapi_set_bw(0x00de): wifi0 as: 80 MHz
rpc_qcsapi_set_channel(0x00f3): wifi0 as: 149
rpc_qcsapi_set_channel(0x00fb): update wireless_conf.txt wifi0 as: 149
rpc_qcsapi_set_beacon_type(0x0118): wifi0 as: 11i
rpc_qcsapi_set_WPA_encryption_modes(0x0135): wifi0 as: AESEncryption
[1 preinit:init_main +56] main loop signal/state=10
cmd[0]=start_firewall
[1 preinit:handle_notifications +56] running: 2 firewall

set default filter settings
zcip:: config done
676: wait for previous script(28/30): start_firewall 723 ip-up.
writting prerouting ppp0 31.207.64.12 eth0 169.254.182.150 br0 192.168.12.1
wanport_status(0) 1
start_nat_rules: apply the nat_rules(/tmp/nat_rules_ppp0_eth0)!
[1 preinit:start_dnsmasq +57] begin
[1 preinit:stop_dnsmasq +57] begin
[1 preinit:stop_dnsmasq +57] end
[1 preinit:start_dnsmasq +57] end
[1 preinit:filter_setting +57] writing vts_enable_x
[1 preinit:filter_setting +57] write porttrigger
[1 preinit:filter_setting +57] write wl filter
[1 preinit:filter_setting +57] write url filter
rpc_qcsapi_set_key_passphrase(0x014b): wifi0 as: ******
rpc_qcsapi_set_dtim(0x015d): wifi0 as: 3
rpc_qcsapi_set_beacon_interval(0x016f): wifi0 as: 100
handle_notifications() end
[1 preinit:init_main +58] main loop signal/state=14
NET CMD GETINFO
NET CMD GETINFO
NET CMD GETINFO
start_ddns update WWW.ASUS.COM dyndns
rpc_qcsapi_set_mac_address_filtering(0x0182): wifi0: 0
[1 preinit:init_main +58] main loop signal/state=10
cmd[0]=start_upnp
[1 preinit:handle_notifications +58] running: 2 upnp
handle_notifications() end
rpc_qcsapi_set_mac_address_filtering(0x0192): wifi0 as: 0 (disabled)
rpc_parse_nvram_from_httpd(0x0052): [80211h] set_80211h_off
qtn_monitor_main(0x00e2): [sw_mode] skip start_ap_qtn, QTN will run scripts automatically
qtn_monitor_main(0x0119): [dbg] qtn_monitor startup
[1 preinit:init_main +60] main loop signal/state=14
ip-up 676:notify_rc: stop_ntpc
ip-up 676:notify_rc: start_ntpc
[1 preinit:init_main +62] main loop signal/state=10
cmd[0]=stop_ntpc
[1 preinit:handle_notifications +62] running: 1 ntpc
676: wait for previous script(29/30): stop_ntpc 676 ip-up.
handle_notifications() end
wan_up(ppp0): done.
ipup_main:: done
[1 preinit:init_main +63] main loop signal/state=10
cmd[0]=start_ntpc
[1 preinit:handle_notifications +63] running: 2 ntpc
handle_notifications() end
starting ntp...
ntp 819:notify_rc: restart_upnp
ntp 819:notify_rc: restart_diskmon
[1 preinit:init_main +64] main loop signal/state=10
cmd[0]=restart_upnp
[1 preinit:handle_notifications +64] running: 3 upnp
handle_notifications() end
[1 preinit:init_main +64] main loop signal/state=10
cmd[0]=restart_diskmon
[1 preinit:handle_notifications +64] running: 3 diskmon
disk_monitor: Finish!
killall_tk: waiting name=disk_monitor n=9
killall_tk: waiting name=disk_monitor n=8
killall_tk: waiting name=disk_monitor n=7
killall_tk: waiting name=disk_monitor n=6
handle_notifications() end
[1 preinit:init_main +65] main loop signal/state=14
disk_monitor: starting...
disk_monitor: day=28, week=0, time=17:31.
disk_monitor: decide if scan the target...
disk_monitor: 0: wait_second=1740...
disk_monitor: 1: wait_second=1740...
disk_monitor: wait_second=1740...
disk_monitor: Pause...

retrieve sig information
no need to upgrade signature

quantenna boot log

quantenna boot log • >>

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.09.28 17:29:02 =~=~=~=~=~=~=~=~=~=~=~=

Quantenna Mini U-Boot
Version: v36.5.0.7 Built:  4жњ€ 21 2014 at 15:19:42
Boot reached stage 64
Boot reached stage 65
QTN-EMAC
Boot reached stage 80
1G-FD
Using QTN-EMAC device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2
Filename 'u-boot.bin'.
Load address: 0x88000000
Loading: T T T T 
Retry count exceeded; starting again
Boot reached stage -81
Boot reached stage 80
1G-FD
BOOTP broadcast 1
BOOTP broadcast 2

Retry count exceeded; starting again
Boot reached stage -81
Boot reached stage 80
1G-FD
Using QTN-EMAC device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2
Filename 'u-boot.bin'.
Load address: 0x88000000
Loading: Quantenna Mini U-Boot
Version: v36.5.0.7 Built:  4жњ€ 21 2014 at 15:19:42
Boot reached stage 64
Boot reached stage 65
QTN-EMAC
Boot reached stage 80
LTN5
Using QTN-EMAC device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2
Filename 'u-boot.bin'.
Load address: 0x88000000
Loading: #############
done
Bytes transferred = 68848 (0x10cf0)
Boot reached stage 81
Boot reached stage 84
Boot reached stage 13
Boot reached stage 12
Valid CRC found in flash restoring env...
Boot reached stage 11
Reset status: 0x00000002
hw_config_id 65535: 'QHS840_5S1'
Cold boot

Info: data uncached: addr=0xc0000000 size=1024MB
Info: text at 0x88014000, stack at 0x88013ffc(8192), 
heap at 0x88000000(73728), uboot size 173140
Info: i-cache is enabled
Info: d-cache is enabled
Info: CPU freq is 500000000, dev freq is 125000000

Info: Quantenna U-Boot version:v36.6.0.7
Info: build date ' 8жњ€ 21 2014', time '23:23:40'

SPI flash info:
	name             : w25x05
	jedec_id         : 0xef3010
	sector size      : 4096
	number of sector : 16
	frequency        : 104000000
	flags            : 0x2
	lock             : 
DDR_INIT: type = 16 speed = 500MHz
BDA at 0x80002000
In:    serial
Out:   serial
Err:   serial
Coot reached stage 64
PHY 0x1cc915 found on MDIO addr:1
Enable phy SSC
Boot reached stage 65
QTN-EMAC
Hit any key to stop autoboot:  2 ��� 1 ��� 0 
Boot reached stage 80
1G-FD
Using QTN-EMAC device
TFTP from server 1.1.1.1; our IP address is 1.1.1.2

Filename 'topaz-linux.lzma.img'.
Load address: 0x83000000
Loading: #################дд#д#############ж################д#############
	 ###д#ж###ц############ж###########д#дд####д#ц#################ж##
	 #######д####д#################д#########д#######д################
	 д##жж##д####жц##########дд############д######жжд####ж#д#########ц
	 ###########ж####ц##############ж##д#####ж#######д#########д####ж#
	 #######ж#######ж#####дд#######ж####д####д########д#######д######ц
	 ####дд#######д##########ж######жддддд############################
	 ##########д######дд##################д#########ж#########ж###д###
	 #################д##############цж##дд################ж##д####жцж
	 ###ж###жж##д#############ж###########ц##ц####ж##########д###д####
	 #дд##############д###############д#цд###д############ж##ж###д####
	 ##ж#######ж##д####ж#####################д####ц###################
	 ##д#########д########ц##д#####ц##д##д#####ж###д###########ж##ж#ж#
	 #######
done
Bytes transferred = 4358750 (0x42825e)
Boot reached stage 81
Boot reached stage 84
Boot reached stage 1

## Booting kernel from Legacy Image at 83000000 ...
Boot reached stage 2
Boot reached stage 3
   Image Name:   topaz-linux
   Image Type:   arc Linux Kernel Image (lzma compressed)
   Data Size:    4350558 Bytes =  4.1 MB
   Load Address: 846da000
   Entry Point:  846da000
   Verifying Checksum ... OK
Boot reached stage 4
Boot reached stage 5
Boot reached stage 6
Boot reached stage 14
   Uncompressing Kernel Image ... OK
Boot reached stage 7
Boot reached stage 8
Command line TAG setup
Params->u.cmdline.cmdline console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
p console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535

## Transferring control to Linux (at address 846da000) ATAG parameters 8803bb50 - 8803bba8...

[    0.000000] Linux version 2.6.35.12 (raymonddev@raymonddev-vm1210) 
               (gcc version 4.2.1 (ARC_2.3)) #2 Thu Aug 21 23:35:41 CST 2014
[    0.000000] Parsing ATAG parameters from bootloader
[    0.000000] ATAG_CORE: successful parsing
[    0.000000] ATAG_CMDLINE: command line = console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
[    0.000000] Board id: 65535
[    0.000000] ATAG_HW_CONFIG_ID: hw_config_id = 65535
[    0.000000] 
[    0.000000] Processor Family: ARC 700 [0x33]
[    0.000000] CPU speed :	500.00 Mhz
[    0.000000] Timers: 	TIMER1 TIMER0 
[    0.000000] Interrupt Vect Base: 	0x88026800 
[    0.000000] Peripheral Base: NOT present; assuming 0xCOFC0000 
[    0.000000] Data UNCACHED Base (I/O): start 0xc0 Sz, 1024 MB 
[    0.000000] ARC700 MMU Ver [2]
[    0.000000]    PAGE SIZE 8k
[    0.000000]    JTLB 128 x 2 = 256 entries
[    0.000000]    uDTLB 8 entr, uITLB 4 entr
[    0.000000] TLB Refill "will NOT" Flush uTLBs
[    0.000000] Detected I-cache : 
[    0.000000]   Type=2 way set-assoc, Line length=32, Size=16K (enabled)
[    0.000000] Detected D-cache : 
[    0.000000]   Type=4 way set-assoc, Line length=32, Size=16K (enabled)
[    0.000000] Extensions:
[    0.000000]    MPY: 32x32 with ANY Result Reg   MAC MPY: Dual 16 x 16 and 32 x 16
[    0.000000]    DCCM: N/A  ICCM: N/A
[    0.000000]    CRC: N/A,   SWAP: Present   NORM: Present
[    0.000000]    Min-Max: Present,   Barrel Shifter: Present
[    0.000000]    Ext Arith Insn: Present
[    0.000000] Floating Point Extension: N/A
[    0.000000] On node 0 totalpages: 16383
[    0.000000] free_area_init_node: node 0, pgdat 8543d9ac, node_mem_map 854e0024
[    0.000000]   Normal zone: 72 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16311 pages, LIFO batch:3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16311
[    0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk=1 hw_config_id=65535
[    0.000000] bootconsole [ruby_early0] enabled
[    0.000000] PID hash table entries: 512 (order: -2, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 3, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 2, 32768 bytes)
[    0.000000] Memory: 43408KB available (2134K code,1137K data, 11080K init)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU debugfs-based tracing is enabled.
[    0.000000] 	Verbose stalled-CPUs detection is disabled.
[    0.000000] clockevent mode switch to [1]
[    0.000000] clockevent mode switch to [2]
[    0.100000] Calibrating delay loop... 248.21 BogoMIPS (lpj=620544)
[    0.105000] pid_max: default: 4096 minimum: 301
[    0.110000] Mount-cache hash table entries: 1024
[    0.115000] Starting run_ksoftirqd, stack (thread_info) at 88010000 cpu 0
[    0.120000] NET: Registered protocol family 16
[    0.125000] Topaz heap in SRAM 880164a0<->88020000
[    0.130000] Quantenna I2C device register
[    0.140000] bio: create slab <bio-0> at 0
[    0.145000] Switching to clocksource ARC Timer1
[    0.155000] NET: Registered protocol family 2
[    0.160000] IP route cache hash table entries: 2048 (order: 0, 8192 bytes)
[    0.165000] TCP established hash table entries: 4096 (order: 2, 32768 bytes)
[    0.170000] TCP bind hash table entries: 4096 (order: 1, 16384 bytes)
[    0.175000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.180000] TCP reno registered
[    0.185000] NET: Registered protocol family 1
[    0.650000] JFFS2 version 2.2. (NAND) Вj’‚‚Љk’‚‚І�’•‘ЃHat, Inc.
[    0.655000] msgmni has been set to 84
[    0.655000] io scheduler noop registered (default)
[    1.085000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[    1.095000] serial8250.0: ttyS0 at MMIO 0xf0000000 (irq = 48) is a 16550A
[    1.100000] console [ttyS0] enabled, bootconsole disabled
[    1.100000] console [ttyS0] enabled, bootconsole disabled
[    1.105000] brd: module loaded
[    1.115000] loop: module loaded
[    1.120000] Creating 3 MTD partitions on "spi_flash":
[    1.125000] 0x000000000000-0x000000005000 : "uboot"
[    1.135000] 0x000000005000-0x00000000b000 : "uboot_env"
[    1.140000] 0x00000000b000-0x000000010000 : "data"
[    1.150000] spi_flash: SPI flash driver initialized successfully!
[    1.155000] ruby_health loading
[    1.650000] topaz_hbm_init_pool_list pool 0 pool_list 0x88000000 
               bus_range 0x4ac000 to 0x24ac000 sz 4096 count 8192
[    1.650000] topaz_hbm_init_pool_list pool 1 pool_list 0x88008000 
               bus_range 0x24ac000 to 0x46ac000 sz 17408 count 2048
[    1.650000] topaz_hbm_init_pool_list pool 3 pool_list 0x8800a000 
               bus_range 0x0 to 0x0 sz 0 count 4096
[    1.655000] topaz_busmon_init success
[    1.660000] topaz_temp_sens_init success
[    1.665000] u32 classifier
[    1.665000]    input device check on
[    1.670000]     Actions configured
[    1.675000] Netfilter messages via NETLINK v0.30.
[    1.680000] nf_conntrack version 0.5.0 (678 buckets, 2712 max)
[    1.685000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.690000] TCP cubic registered
[    1.690000] NET: Registered protocol family 10
[    1.700000] NET: Registered protocol family 17
[    1.705000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    1.710000] All bugs added by David S. Miller <davem@redhat.com>
[    1.720000] Freeing unused kernel memory: 11080k freed [846da000] TO [851ac000]
[    1.725000] Common mmap addr-space starts 2b0f0000

init started: BusyBox v1.10.3 (2014-08-21 23:24:37 CST)

starting pid 36, tty '': '/etc/init.d/rcS'
Starting portmap: done
Initializing random number generator... done.

[    2.080000] load_module: 'bootcfg' using DRAM (offset:0x861f0000, size:0x8f08)

current qtn_hw_config name:  QHS840_5S1
current qtn_hw_config wifi_hw:  8
Starting network...

[    2.730000] load_module: 'rtl8367b' using DRAM (offset:0x86240000, size:0x32435)
[    2.735000] rtl8367b: module license 'unspecified' taints kernel.
[    2.775000] Disabling lock debugging due to kernel taint
[    2.825000] load_module: 'emaclib' using DRAM (offset:0x86280000, size:0x509e)
[    2.905000] load_module: 'dpi' using DRAM (offset:0x86194000, size:0x1bb9)
[    2.935000] load_module: 'fwt_if' using DRAM (offset:0x8788e640, size:0x1168)
[    2.965000] load_module: 'switch_tqe' using DRAM (offset:0x86218000, size:0x36ef)Cб
[    2.990000] tqe_descs_alloc: 512 tqe_rx_descriptors at kern uncached 0x550e04a8 bus 0x800164a8
[    3.030000] load_module: 'fwt_ctrl' using DRAM (offset:0x862a0000, size:0x1f091)
[    3.085000] load_module: 'switch_emac' using DRAM (offset:0x86198000, size:0x179d)Cб
[    3.120000] topaz_emac_init, emac0
[    3.125000] Random stuff 96
[    3.785000] emac_eth_mii: probed
[    3.785000] emac_lib eth1_emac0: index 0 id 0x1cc915 addr 0
[    3.790000] emac_lib eth1_emac0: index 1 id 0x1cc915 addr 1
[    3.795000] emac_lib eth1_emac0: phy_id 0x1cc915 addr 1
[    3.835000] emac_lib eth1_emac0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=mdio_bus, irq=-1)
[    3.845000] topaz_dpi_init initialized for emac0
[    3.850000] topaz_emac_init, emac1
[    3.855000] topaz_dpi_init initialized for emac1

emac0 is eth1_1, emac1 is eth1_0
Stateless mode. Using temporary ip address: 
cat: can't open '/mnt/jffs2/nvram.txt': No such file or directory
------------------------------
------------------------------
Using IP address 169.254.39.2
Using netmask 255.255.255.0

[    4.500000] emac_lib eth1_0: force link (1000/Full)
[    4.510000] device eth1_0 entered promiscuous mode
[    4.520000] br0: port 1(eth1_0) entering forwarding state
[    4.525000] br0: port 1(eth1_0) entering forwarding state

sed: mnt/jffs2/wireless_conf.txt: No such file or directory

[    4.600000] device eth1_1 entered promiscuous mode
[    4.605000] br0: port 2(eth1_1) entering forwarding state
[    4.610000] br0: port 2(eth1_1) entering forwarding state
[    4.615000] FWT: [d4:ca:6d:33:41:a3] add entry, port:emac1 node:0 entries:1

/sbin/ifup -a

[    4.740000] FWT: [78:24:af:93:af:f0] add entry, port:emac1 node:0 entries:2

ifconfig: SIOCSIFNETMASK: Cannot assign requested address
ifconfig: SIOCSIFNETMASK: Cannot assign requested address

[    4.905000] eth1_1: link up (1000/Full)
[    4.905000] FWT: [90:2b:34:5e:70:42] add entry, port:emac0 node:0 entries:3

Telnet disabled
Starting wireless...

[    5.215000] FWT: [3c:4a:92:74:35:e8] add entry, port:emac0 node:0 entries:4
[    5.220000] FWT: [ac:f2:c5:35:37:2a] add entry, port:emac0 node:0 entries:5

-----------------------------------------------------------------
-----------------------------------------------------------------
Creating wireless_conf.txt from default_config.txt
[restore] change pwr from 19 to 23

[    5.900000] FWT: [d8:50:e6:f3:36:64] add entry, port:emac0 node:0 entries:6

[5G] ccode_5g us found, set wireless driver and update to wireless_conf
complete

rm: cannot remove '/scripts/router_command.sh': No such file or directory
=== Waiting for stateless slave to boot

[    9.875000] FWT: [00:0c:29:00:2b:eb] add entry, port:emac0 node:0 entries:7
[   10.450000] FWT: [a8:20:66:12:17:ef] add entry, port:emac0 node:0 entries:8
[   10.455000] FWT: [84:34:97:b5:84:38] add entry, port:emac1 node:0 entries:9

=== Starting stateless slave configuration
=== Setting bf to 1
complete

[   11.705000] FWT: [60:51:2c:42:77:20] add entry, port:emac1 node:0 entries:10

=== Setting bw to 80
complete
=== Setting channel to 149
complete
=== Setting mode to ap
complete
=== Setting pwr to 23
complete
=== Setting region to us

Jan  1 00:00:12 qcsapi_regulatory_database[477]: database /proc/bootcfg/qtn_regulatory_db.bin is loaded.

complete
=== Setting staticip to 1
complete
=== Setting vht to 1
complete
=== waiting start-prod
complete
cat: can't open '/mnt/jffs2/nvram.txt': No such file or directory
=== waiting start-prod
------------------------------
------------------------------
Using IP address 169.254.39.2
Using netmask 255.255.255.0
Loading modules

[   13.980000] load_module: 'qtn_debug' using DRAM (offset:0x86216000, size:0x403)
[   14.040000] load_module: 'i2cbus' using DRAM (offset:0x862f9000, size:0xbb2)
[   14.065000] se95-i2c : I2C driver register code = 0 
[   14.130000] load_module: 'qtsens' using DRAM (offset:0x86216800, size:0x7bf)
[   14.150000] temp_sensor: (SE95) has not been detected
[   14.225000] load_module: 'pm_interval' using DRAM (offset:0x86384000, size:0x13b2)
[   14.325000] load_module: 'wlan' using DRAM (offset:0x86400000, size:0x5deb1)
[   14.535000] wlan: 0.8.4.2 (0.9.3.3)
[   14.685000] load_module: 'radar' using DRAM (offset:0x863c0000, size:0x19ded)
[   14.735000] load_module: 'qvspmod' using DRAM (offset:0x863a0000, size:0x10503)
[   14.820000] load_module: 'qdrv' using DRAM (offset:0x86500000, size:0x7cc58)
[   15.050000] load_module: 'wlan_xauth' using DRAM (offset:0x862ea800, size:0x32f)
[   15.250000] load_module: 'wlan_ccmp' using DRAM (offset:0x8639e000, size:0x17b6)
[   15.350000] load_module: 'wlan_tkip' using DRAM (offset:0x863f4000, size:0x265e)

[RT-AC87U] start syslogd
Loading MuC driver (qtn_driver.qtn_ruby.0.bin)
Waiting for Wireless Events from interfaces...
MYROUTER: wifi_mode=[ap]

[   16.125000] MuC: uc_print_initialise_shared_data linux buf 557c1a80
[   16.130000] MuC: build date=Wed Aug 13 18:40:49 PDT 2014
[   16.135000] MuC: slow heap begin=0x001d3a20 end=0x0032fa20
[   16.140000] MuC: fast heap begin=0x800307a0 end=0x800387a0
[   16.145000] MuC: stack start=0x8003efc0 sp=0x8003f724
[   16.150000] MuC: calstate is 3 (prod), dcache on
[   16.155000] MuC: scancnt=4
[   16.155000] MuC: 4x4 11ac FO RGMII/PCIe QV840
[   16.225000] MuC: RFIC version = 1
[   16.240000] MuC: os_uc, after bb_rf_complete_attach.
[   16.245000] MuC: fd start=0xe5040300 count=48 size=108 end=0xe5041740
[   16.250000] MuC: TX QoS schedule=0
[   16.255000] MuC: dynamic one-bit autocorrelation enabled
[   16.260000] MuC: bbrf_get_RFIC_freqID 1 g_proj_ID 1
[   16.265000] MuC: enable IRQs
[   16.270000] MuC: Wait for AuC ready
[   16.270000] MuC: Sync with AuC
[   16.275000] MuC: AuC is booted: 0xe5100ba4:0x6005e918 auc ilink addr: 0xe510025c:0xe5100260
[   16.280000] MuC: node stats - 0x6005d258
[   16.280000] MuC: vap  stats - 0x6005e5d8
[   16.285000] AuC: uc_print_initialise_shared_data linux buf 55fc01f8
[   16.290000] qdrv_wlan_80211_init rf_chipid 1
[   16.295000] QDRV: power adjust scancnt=0
[   16.300000] QDRV: using default temperature profile
[   16.305000] QDRV: could not read temperature sensor
[   16.310000] MuC boot succeeded 0.095 seconds
[   16.395000] load_module: 'wlan_scan_ap' using DRAM (offset:0x864ea000, size:0x1f66)
[   16.515000] MuC: bbrf_get_RFIC_freqID 1 g_proj_ID 1
[   16.545000] VAP create succeeded 0.020 seconds
[   16.815000] set_cap_bw: ic_phymode = 13 
[   16.860000] MuC: g_calibration_algo_ver_to_report_dciq == 0x801

copy /scripts/sysdeps/RT-AC87U/tx_power to /etc/
[5G] ccode_5g us found, set wireless driver and update to wireless_conf
radar in 80MHZ mode

version of /proc/bootcfg/qtn_regulatory_db.bin is v36.5.0.4
version of /etc/qtn_regulatory_db.bin is v36.6.0.3
Select database version: v36.6.0.3
Configuring to load /etc/qtn_regulatory_db.bin

[   17.725000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (52)
[   17.730000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (56)
[   17.735000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (60)
[   17.740000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (64)
[   17.745000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (100)
[   17.750000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (104)
[   17.755000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (108)
[   17.760000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (112)
[   17.765000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (116)
[   17.770000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (120)
[   17.775000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (124)
[   17.780000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (128)
[   17.785000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (132)
[   17.790000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (136)
[   17.795000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (140)
[   17.800000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (144)

radar start with regulatory us

[   18.825000] OCAC: parameters updated, country_code: 840
[   19.100000] device wifi0 entered promiscuous mode
[   19.150000] Enabling SSDP flooding

Enabling beamforming
802.11ac Enabled

[   19.675000] qdrv_sch_red: available tokens (8) is not enough
[   19.775000] qdrv_sch_red: attached to eth1_0

SCS disabled
DSP: load profile off

[   20.005000] qvsp_ioctl_rule_del_index: rule delete done
[   20.055000] qvsp_strm_reset: stream reset

VSP enabled: 0
.K�’б sts: unknown operand

[   20.360000] start ba_setup detect timer 
[   20.745000] [2]Comparing register set Global control
[   20.765000] [6]Comparing register set BB Global regs

RT-AC87U: monitor led
monitor_wifi: no process killed
monitor ID 0, uboot update flag 0
complete
complete

[   21.985000] FWT: [01:00:5e:00:01:01] add entry, port:emac1 node:0 entries:11

=== Setting security parameters
=== Setting AP parameters
=== Setting SSID to ******
complete
=== Setting Authentication protocol to 11i
complete
=== Setting WPA encryption mode to AESEncryption
complete
=== Setting WPA authentication mode to PSKAuthentication
complete
=== Setting passphrase to ******
complete
=== Starting wireless

[   24.120000] MuC: Soft TQE ring init. emac0 size = 1024, emac1 size = 1024
[   24.125000] MuC: RALG: Error 11ac 4ss table index 22 rate 22 has incorrect higher rate 13
[   24.130000] MuC: RALG: Error 11ac 4ss table index 33 rate 34 has incorrect higher rate 24
[   24.135000] AuC: triple: free 0 rxq 8 8 64 descriptors: addr 0x80040100 size 1280 rx status: addr 0x80040600 size 2560
[   24.140000] AuC: last_ilink1 addr=0xe510025c, last_ilink2 addr=0xe5100260
[   24.145000] AuC: AuC rx watchdog started
[   24.155000] WPS: push button is not configured
[   24.160000] MuC: WMM AC 0:3,4,6,0 1:7,4,10,0 2:1,3,4,188 3:1,2,3,188 
[   24.165000] br0: port 3(wifi0) entering forwarding state
[   24.170000] br0: port 3(wifi0) entering forwarding state

start-prod: adding default "manufacturer=ASUS" to /mnt/jffs2/hostapd.conf
start-prod: adding default "device_name=Router" to /mnt/jffs2/hostapd.conf
start-prod: adding default "model_name=Router" to /mnt/jffs2/hostapd.conf
start-prod: adding default "model_number=QV860.00" to /mnt/jffs2/hostapd.conf
start-prod: adding default "serial_number=7824AF93AFF4" to /mnt/jffs2/hostapd.conf
start-prod: adding default "friendly_name=UPnP Access Point" to /mnt/jffs2/hostapd.conf
start-prod: adding default "device_type=6-0050F204-1" to /mnt/jffs2/hostapd.conf

[   24.830000] br0: port 3(wifi0) entering forwarding state
[   24.930000] br0: port 3(wifi0) entering forwarding state
[   25.675000] br0: port 3(wifi0) entering forwarding state

complete

=== Applying security configuration

Wait 20 seconds to start stateless

S55rpc startup

starting pid 1061, tty '/dev/console': '/bin/sh -l'
/scripts/cmdloop starting /sbin/call_qcsapi_rpcd, at 00:00:26 up 0 min, load average: 0.40, 0.09, 0.03
/scripts/cmdloop starting /sbin/qcsapi_rpcd, at 00:00:26 up 0 min, load average: 0.40, 0.09, 0.03

BusyBox v1.10.3 (2014-08-21 23:24:37 CST) built-in shell (ash)

Enter 'help' for a list of built-in commands.

/scripts/cmdloop starting /sbin/rmt_qcsapi_server, at 00:00:26 up 0 min, load average: 0.40, 0.09, 0.03

quantenna # complete

=== Apply some hardware wireless setting
=== Setting IP address and netmask to 169.254.39.75
=== skip get tweak_qcomm
=== Done setting up stateless slave

[   28.060000] (RF,BB) = (12, 3), (12, 3), (12, 0), (12, 10)
[   28.065000]  Voltage = 106, 130, 195, 296
[   28.070000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   28.070000] TEMPERATURE_RFIC_INTERAL = 44.1
[   28.090000] set_cap_bw: ic_phymode = 13 
[   28.165000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (52)
[   28.170000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (56)
[   28.180000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (60)
[   28.185000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (64)
[   28.190000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (100)
[   28.195000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (104)
[   28.200000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (108)
[   28.205000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (112)
[   28.210000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (116)
[   28.215000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (120)
[   28.220000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (124)
[   28.225000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (128)
[   28.230000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (132)
[   28.235000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (136)
[   28.240000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (140)
[   28.245000] ieee80211_ioctl_set_chan_dfs_required: Mark DFS channel (144)
[   29.200000] radar start with
[   29.250000] qdrv_radar_enable: ERROR - radar already enabled regulatory us
[   29.260000] OCAC: parameters updated, country_code: 840
[   31.875000] wifi0: station 10:08:c1:05:b8:ec associated, tot=1/1
[   31.930000] wifi0: station 10:08:c1:05:b8:ec disassociated, tot=0/0
[   31.955000] (RF,BB) = (12, 3), (12, 3), (12, 0), (12, 10)
[   31.960000]  Voltage = 107, 130, 194, 474
[   31.965000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   31.965000] TEMPERATURE_RFIC_INTERAL = 44.1
[   32.350000] FWT: [00:0c:29:2f:56:c3] add entry, port:emac0 node:0 entries:12
[   32.355000] FWT: [00:0c:29:f2:58:b9] add0entry, port:emac0 node:0 entries:13
[   32.360000] FWT: [00:0c:29:1f:d0:5f] add entry, port:emac0 node:0 entries:14
[   32.395000] FWT: [00:0c:29:c2:74:02] add entry, port:emac0 node:0 entries:15
[   32.585000] wifi0: station 10:08:c1:05:b8:ec associated, tot=1/1
[   32.625000] FWT: [10:08:c1:05:b8:ec] add entry, port:wmac node:6 entries:16
[   35.890000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   35.895000]  Voltage = 477, 469, 506, 475
[   35.895000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   35.900000] TEMPERATURE_RFIC_INTERAL = 44.1
[   36.300000] wifi0: [10:08:c1:05:b8:ec] block ack allowed by peer tid: 0 size 16
[   36.300000] wifi0: [10:08:c1:05:b8:ec] block ack allowed by peer tid: 6 size 16
[   36.380000] FWT: [01:00:5e:00:00:fa] add entry, port:wmac node:6 entries:17
[   39.830000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   39.835000]  Voltage = 477, 470, 506, 470
[   39.835000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   39.840000] TEMPERATURE_RFIC_INTERAL = 44.1
[   43.830000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   43.830000]  Voltage = 477, 467, 506, 472
[   43.830000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   43.835000] TEMPERATURE_RFIC_INTERAL = 44.1
[   47.400000] wifi0: station 38:aa:3c:0f:45:c7 associated, tot=2/2
[   47.460000] FWT: [38:aa:3c:0f:45:c7] add entry, port:wmac node:7 entries:18
[   47.825000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   47.830000]  Voltage = 475, 465, 506, 468
[   47.830000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   47.835000] TEMPERATURE_RFIC_INTERAL = 44.1
[   49.440000] wifi0: [38:aa:3c:0f:45:c7] block ack allowed by peer tid: 0 size 8
[   49.440000] wifi0: [38:aa:3c:0f:45:c7] block ack allowed by peer tid: 6 size 8
[   51.820000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   51.825000]  Voltage = 460, 444, 494, 472
[   51.825000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   51.830000] TEMPERATURE_RFIC_INTERAL = 44.1
[   55.820000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   55.825000]  Voltage = 452, 453, 494, 470
[   55.825000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   55.830000] TEMPERATURE_RFIC_INTERAL = 44.1
[   59.900000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   59.905000]  Voltage = 452, 468, 505, 467
[   59.905000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   59.910000] TEMPERATURE_RFIC_INTERAL = 44.1
[   63.835000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   63.840000]  Voltage = 503, 442, 506, 470
[   63.840000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   63.845000] TEMPERATURE_RFIC_INTERAL = 44.1
[   67.830000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   67.835000]  Voltage = 502, 466, 505, 465
[   67.835000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   67.840000] TEMPERATURE_RFIC_INTERAL = 44.1
[   71.830000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   71.835000]  Voltage = 472, 465, 504, 469
[   71.835000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   71.840000] TEMPERATURE_RFIC_INTERAL = 44.1
[   75.830000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   75.835000]  Voltage = 473, 464, 505, 468
[   75.835000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   75.840000] TEMPERATURE_RFIC_INTERAL = 44.1
[   75.840000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   79.835000]  Voltage = 472, 466, 505, 466
[   79.835000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   79.840000] TEMPERATURE_RFIC_INTERAL = 44.1
[   81.640000] wifi0: [38:aa:3c:0f:45:c7] block ack allowed by peer tid: 1 size 8
[   83.830000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   83.830000]  Voltage = 451, 465, 492, 469
[   83.835000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   83.835000] TEMPERATURE_RFIC_INTERAL = 44.1
[   87.830000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   87.835000]  Voltage = 473, 462, 504, 468
[   87.835000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   87.840000] TEMPERATURE_RFIC_INTERAL = 44.1
[   90.590000] FWT: [01:00:5e:00:00:fa] add IPv4: 239.0.0.2500port:emac0 node:0
[   91.810000] FWT: [01:00:5e:00:01:3c] add entry, port:emac1 node:0 entries:19
[   91.840000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   91.840000] Voltage = 469, 465, 498, 469
[   91.850000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   91.850000] TEMPERATURE_RFIC_INTERAL = 44.1
[   91.990000] FWT: [01:00:5e:40:98:8f] add entry, port:emac0 node:0 entries:20
[   94.960000] FWT: [01:00:5e:28:a8:a8] add entry, port:emac0 node:0 entries:21
[   95.830000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   95.835000]  Voltage = 450, 464, 505, 467
[   95.835000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   95.840000] TEMPERATURE_RFIC_INTERAL = 45.3
[   99.830000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[   99.835000]  Voltage = 471, 464, 504, 467
[   99.835000] TEMPERATURE_RFIC_EXTERAL= 0.0
[   99.840000] TEMPERATURE_RFIC_INTERAL = 44.1
[  103.825000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[  103.830000]  Voltage = 470, 463, 504, 467
[  103.835000] TEMPERATURE_RFIC_EXTERAL= 0.0
[  103.835000] TEMPERATURE_RFIC_INTERAL = 44.1
[  107.835000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[  107.840000] Voltage = 470, 463, 505, 465
[  107.840000] TEMPERATURE_RFIC_EXTERAL= 0.0
[  107.845000] TEMPERATURE_RFIC_INTERAL = 45.3
[  111.830000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[  111.835000]  Voltage = 470, 462, 504, 468
[  111.835000] TEMPERATURE_RFIC_EXTERAL= 0.0
[  111.840000] TEMPERATURE_RFIC_INTERAL = 44.1
[  115.830000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[  115.835000]  Voltage = 468, 463, 505, 468
[  115.835000] TEMPERATURE_RFIC_EXTERAL= 0.0
[  115.840000] TEMPERATURE_RFIC_INTERAL = 45.3
[  119.060000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[  119.065000]  Voltage = 438, 464, 504, 462
[  119.065000] TEMPERATURE_RFIC_EXTERAL= 0.0
[  119.070000] TEMPERATURE_RFIC_INTERAL = 45.3
[  121.445000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[  121.450000]  Voltage = 469, 463, 505, 466
[  121.450000] TEMPERATURE_RFIC_EXTERAL= 0.0
[  121.455000] TEMPERATURE_RFIC_INTERAL = 45.3
[  124.815000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[  124.820000]  Voltage = 470, 464, 492, 466
[  124.820000] TEMPERATURE_RFIC_EXTERAL= 0.0
[  124.825000] TEMPERATURE_RFIC_INTERAL = 45.3
[  128.815000] (RF,BB) = (19, 3), (18, 4), (17, 0), (12, 10)
[  128.820000]  Voltage = 470, 463, 504, 462
[  128.820000] TEMPERATURE_RFIC_EXTERAL= 0.0
[  128.825000] TEMPERATURE_RFIC_INTERAL = 45.3

Pictures

PCB @ Asus

Retail Images

User Images

PCB top
PCB serial
Board top
CPU, RAM, RFIC, PA
Quantenna 5 GHz

v t e ASUS AC products.
xDSL Modem / Wireless Router	ASUS DSL-AC88U • AC3100 Dual-Band Wireless Gigabit xDSL Modem Router • Product Page ASUS DSL-AC87VG • AC2400 Dual-Band Wi-Fi xDSL VoIP Modem Router • Product Page ASUS DSL-AC68U • AC1900 Dual-Band Wireless Gigabit xDSL Modem Router • Product Page ASUS DSL-AC56U • AC1200 Dual-Band Wi-Fi xDSL Modem Router • Product Page ASUS DSL-AC55U • AC1200 Dual Band Wi-Fi xDSL Modem Router • Product Page ASUS DSL-AC52U • AC750 Dual-Band Wi-Fi xDSL Gigabit Modem Router • Product Page
Range Extender	ASUS RP-AC87 • (Wireless-AC2400) MTK • Support Page ASUS RP-AC68U • AC1900 (450+1733Mbps) • Product Page ASUS RP-AC66 • (Wireless-AC1750) QCA • Product Page ASUS RP-AC56 • AC1200 (300+867Mbps) • Product Page ASUS RP-AC53 • AC750 Dual-Band Wi-Fi Repeater • Product Page ASUS RP-AC52 • AC750 (300+433Mbps) • Product Page
Media Bridge	ASUS EA-AC87 • AC1800 (1733Mbps) QT • Product Page
Wireless Adapter	ASUS PCE-AC88 • AC3100 (1000+2167Mbps) adapter • Product Page ASUS PCE-AC68 • AC1900 (600+1300Mbps) adapter • Product Page ASUS PCE-AC66 • AC1750 (450+1300Mbps) adapter • Product Page ASUS PCE-AC56 • AC1300 (400+867Mbps) adapter • Product Page ASUS USB-AC68 • AC1900 (600+1300Mbps) adapter • Product Page ASUS USB-AC56 • AC1300 (400+867Mbps) adapter • Product Page ASUS USB-AC56R • AC1300 (400+867Mbps) adapter • Product Page ASUS USB-AC55 • AC1300 (400+867Mbps) adapter • Product Page ASUS USB-AC53 Nano • AC1200 (300+867Mbps) adapter • Product Page ASUS USB-AC53 • AC1200 (300+867Mbps) adapter • Product Page ASUS USB-AC51 • AC600 (150+433Mbps) adapter • Product Page ASUS USB-AC50 • AC450 (433Mbps) adapter • Product Page
Wireless Router	ASUS GT-AC5300 ROG • AC5300 (1000+2x2167Mbps) • Product Page ASUS RT-AC5300 • AC5300 (1000+2x2167Mbps) • Product Page ASUS RT-AC3200 • AC3200 (600+2x1300Mbps) • Product Page • Asus PC DIY ASUS RT-AC3100 • AC3100 (1000+2167Mbps) • Product Page ASUS BRT-AC828/M2 • (Wireless-AC2600) • Product Page ASUS BRT-AC414 • (Wireless-AC1300) • Product Page ASUS RT-AC1900 • (Wireless-AC1900) • Product Page ASUS RT-AC1900P • (Wireless-AC1900) • Product Page ASUS SRT-AC1900 • AC1900 (600+1300Mbps) • Product Page • Asus News (US) ASUS TM-AC1900 • AC1900 (600+1300Mbps) • Support Page ASUS RT-AC1750 • (Wireless-AC1750) • Product Page (US) ASUS RT-ACRH13 • (Wireless-AC1300) • Product Page (US) ASUS RT-AC1200 • AC1200 (300+867Mbps) • Product Page ASUS RT-AC1200G • AC1200 (300+867Mbps) • Product Page ASUS RT-AC1200GP(+) • AC1200 (300+867Mbps) • Product Page ASUS RT-AC1200GU • AC1200 (300+867Mbps) • Product Page ASUS RT-AC1200HP • AC1200 (300+867Mbps) • Product Page ASUS RT-AC88U • AC3100 (1000+2167Mbps) • Product Page ASUS RT-AC87R • AC2400 (600+1733Mbps) • Product Page ASUS RT-AC87U • AC2400 (600+1733Mbps) • Product Page • Asus PC DIY ASUS RT-AC86U • AC2900 (750+2167Mbps) • Product Page ASUS RT-AC85U • (Wireless-AC2600) • Product Page (JP) ASUS RT-AC68P • AC1900 (600+1300Mbps) • Product Page ASUS RT-AC68R • AC1900 (600+1300Mbps) • Product Page ASUS RT-AC68U • AC1900 (600+1300Mbps) • Product Page ASUS RT-AC68W • AC1900 (600+1300Mbps) • Product Page ASUS RT-AC66R • AC1900 (600+1300Mbps) • Product Page ASUS RT-AC66U • AC1750 (450+1300Mbps) • Product Page ASUS RT-AC66U B1 • AC1750 (450+1300Mbps) ASUS RT-AC66W • AC1900 (600+1300Mbps) • Product Page ASUS RT-AC58U • (Wireless-AC1300) • Product Page ASUS RT-AC56R • AC1200 (300+867Mbps) • Product Page ASUS RT-AC56S • AC1200 (300+867Mbps) • Product Page ASUS RT-AC56U • AC1200 (300+867Mbps) • Product Page ASUS RT-AC55UHP • AC1200 (300+867Mbps) • Product Page ASUS RT-AC55U • AC1200 (300+867Mbps) • Product Page ASUS 4G-AC55U • AC1200 (300+867Mbps) • Product Page ASUS RT-AC54U • AC1200 (300+867Mbps) • Product Page ASUS RT-AC53U • AC1200 (300+867Mbps) • Product Page ASUS RT-AC53 • AC750 (300+433Mbps) • Product Page ASUS RT-AC52U • AC750 (300+433Mbps) • Product Page ASUS RT-AC51U • AC 750 (300+433Mbps) • Product Page

ASUS RT-AC87U

Overview

Links of Interest

Reviews

Forum threads

Blogs

Press releases

Other

Flashing

Flashing dd-wrt

Flashing OpenWrt

JTAG-Serial Info

Serial

Broadcom boot log

quantenna boot log

Pictures

See also

Navigation menu

Page actions

Page actions

Personal tools

Search

Navigation

data/misc

Tools

query forms

ShoutWiki messages

abgn+ac (AC2400)
Dual-band Wireless-AC2400 Gigabit Router

Homepage	Product page (RT-AC87U) Product page (RT-AC87R)
Wikipedia	Asus routers
WikiDevi.wi-cat.ru	ASUS RT-AC87U
3rd Party Firmware
dd-wrt	Supported
OpenWrt	Partial Support
Tomato any flavor	Status Unknown
Gargoyle	Status Unknown
Platform
Brand • Model • Rev	ASUS RT-AC87U
FCC ID	MSQ-RTAC87U
IC ID	3568A-RTAC87U
Type	wireless router
CPU1	Broadcom BCM4709A0
CPU1 Type	ARMv7 Cortex-A9
CPU1 Speed	1.0 GHz ( 2 cores )
CPU2	Quantenna QT3840BC
CPU2 Type	ARC 700
CPU2 Speed	500 MHz ( 2 cores )
Flash1 Chip	Spansion S34ML01G100TFI00
Flash1 Size	128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
Flash2 Chip	Winbond W25X05CL
Flash2 Size	0.065 MiB68,157.44 B <br />532.48 Kib <br />66.56 KiB <br />0.52 Mib <br />6.347656e-5 GiB <br />
RAM1 Size	256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br />
RAM1 Chip	ESMT M15F2G16128A-BDB
RAM2 Size	128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br />
RAM2 Chip	ESMT M15F1G1664A-ADB
ETH chip1	Broadcom BCM4709A0
ETH chip2	Realtek RTL8211E
Switch	Broadcom BCM4709A0
Ethernet Port Count	1-1GbE-WAN 4-1GbE-LAN
Wired Standard	IEEE 802.3i/3u/3ab
802dot11 OUI: 10:C3:7B (2 E, 2 W), 78:24:AF Ethernet OUI: 10:C3:7B (2 E, 2 W), 78:24:AF
Stock bootloader	CFE 6.37 U-Boot v36.5
Stock FW OS	Linux 2.6.35
Expansion IF types	USB 2.0, USB 3.0
USB ports	2
USB Hub Compatible	Untested
Power	19 VDC, 2.37 A
Connector type	barrel
Serial Port (UART)	yes, 4-pin header
Flags: Wave2, AiCloud support
Additional chips 2.4GHz Power Amplifier IC;Richwave;RTC6649E;;3; 5GHz Power Amplifier IC;Skyworks;SKY85402-11;SKY, 85402, 11;3;
Other
Default SSID: ASUS (100 addl. devices) , ASUS_5G (46 addl. devices) Default IP address: 192.168.1.1 the IP 192.168.1.1 is used by 1324 additional devices of which 173 are ASUS devices Default login user: admin Default login password: admin admin:admin credentials used by 1342 additional devices of which 207 are ASUS devices
Manuf/OEM/ODM	Arcadyan WG9117A AC44-ASU
3rd Party Firmware Support	AsusWRT-Merlin • (Wiki \| List) , DD-WRT • (List) , OpenWrt • (List \| Dev \| DLs)
Retail
Availability	common
FCC approval date	30 June 2014
Newegg	9SIADXX5TA3027
ASIN	B00MPI5N7U
Country of manuf	China
Radio 1
Chip1	Quantenna QT3840BC
Chip2	Quantenna QT2518B
Wireless interface OUI	10:C3:7B, 78:24:AF
Antenna Connector Type	U.FL, RP-SMA
MIMO status	4x4:4
Wireless Standard	IEEE 802.11a/n/ac
802.11ac	up to 1733 Mbps
802.11n	up to 600 Mbps
802.11a	up to 54 Mbps
WiFi Operating Frequency	5 GHz
Radio 2
Chip1	Broadcom BCM4360
Wireless interface OUI	10:C3:7B, 78:24:AF
Antenna Connector Type	U.FL, RP-SMA
MIMO status	3x3:3
Wireless Standard	IEEE 802.11b/g/n
N-QAM	up to 600 Mbps
802.11n	up to 450 Mbps
802.11g	up to 54 Mbps
802.11b	up to 11 Mbps
WiFi Operating Frequency	2.4 GHz
Radio cor_rev	40