ZyXEL XGS1250-12

From TechInfoDepot
Jump to navigationJump to search
3rd Party Firmware
dd-wrt
Status Unknown
OpenWrt
Status Unknown
Tomato any flavor
Incompatible
Platform
Brand • Model • Rev
ZyXEL XGS1250-12
Board ID
2976966401
CPU1
Realtek RTL9302B
CPU1 Type
MIPS 34Kc
CPU1 Speed
800 MHz
Flash1 Chip
Macronix MX25L12833F
Flash1 Size
16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br />
RAM1 Size
128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> (DDR3 SDRAM)
RAM1 Chip
Winbond W613GU6MB-12
ETH chip1
Realtek RTL9302B
ETH chip2
Realtek RTL8218D
ETH chip3
Aquantia AQR113C
ETH chip4
Aquantia AQR113C
ETH chip5
Aquantia AQR113C
Switch
Realtek RTL9302B
Ethernet Port Count 12-1GbE
Ethernet connector 8P8C
Wired Standard unspecified
Auto-MDIX supported
Jumbo frame
yes
Switch Class
managed

Ethernet OUI: none specified

Expansion IF types
SFP+
SFP ports
1
Serial Port (UART)
yes, 4-pin header
Other
Manuf/OEM/ODM

Additional chips
Serial GPIO/LED Display Controller;Realtek;RTL8231;;1;

Retail
(Est.) release date November 2021

For a list of all currently documented Aquantia SoC's with specifications, see Aquantia.
For a list of all currently documented Realtek chipsets with specifications, see Realtek.

For a list of all currently documented ZyXEL device with specifications, see ZyXEL.

Overview

The XGS1250-12 is a 11 + 1-port Multi-Gigabit L3 switch. It has 8 Gigabit ports, three 2.5/5/10GBit Ethernet ports and one SFP+ 10GBit uplink cages.

Power is supplied via a 12V 2A standard barrel connector. At the right side behind the grid is UART serial connector. A Serial header can be connected to from the outside of the switch trough the airvents with a standard 2.54mm header. Pins are from top to bottom Vcc(3.3V), TX, RX and GND. Serial connection is via 115200 baud, 8N1.

Links of Interest

Notes

------------------ Board Configuration ------------------

****************************
 ZYXEL XGS1250-12
****************************
============================
 Board GPIO
============================
Device  Pin  Direction  Default  Current  Purpose
------- ---- ---------- -------- -------- --------
INT     0    OUT        0        0        
INT     1    IN         1        1        FAN_CONTROL
INT     6    IN         1        0        HW_VER_BIT1
INT     7    IN         1        1        HW_VER_BIT0
INT     11   OUT        0        0        FAN_EN
INT     15   OUT        0        0        TX_DIS_P11
INT     16   IN         0        1        SFP_Present_P11
INT     17   IN         0        1        SFP_LOS_P11
INT     20   IN         0        0        TX_FAULT_P11
INT     21   OUT        1        1        RESET_PHY
INT     22   IN         1        1        RST_BTN_OUT

============================
 Board Configuration
============================
====== Port ==================
Type        Usr  Phy     Media       Speed          Duplex   Attr
----------- ---- ------- ----------- -------------- -------- -------
1000M       1    (0) 0   Copper      (A) ALL        Auto     0      
1000M       2    (0) 1   Copper      (A) ALL        Auto     0      
1000M       3    (0) 2   Copper      (A) ALL        Auto     0      
1000M       4    (0) 3   Copper      (A) ALL        Auto     0      
1000M       5    (0) 4   Copper      (A) ALL        Auto     0      
1000M       6    (0) 5   Copper      (A) ALL        Auto     0      
1000M       7    (0) 6   Copper      (A) ALL        Auto     0      
1000M       8    (0) 7   Copper      (A) ALL        Auto     0      
10G         9    (0) 24  Copper      (A) ALL        Auto     0      
10G         10   (0) 25  Copper      (A) ALL        Auto     0      
10G         11   (0) 26  Copper      (A) ALL        Auto     0      
10G         12   (0) 27  Fiber       (F) 10G        (F) Full 0      


====== Fiber =================
Fiber Port Number: 1

------------ Fiber Detect
LPort  Present  MediaChg  OE Status              LOS Status
------ -------- --------- ---------------------- ----------------------
11     OE       None      Enabled  (GPIO:INT_16) Enabled  (GPIO:INT_17)

------------ Fiber Optical
LPort  I2C DEV  I2C TYPE  ID    Delay   SCK    SDA
------ -------- --------- ----- ------- ------ ------
11     2        8 BITS    0x50  50      INT_8  INT_10

------------ Fiber TX Disable
LPort  Method
------ ------
11     GPIO(INT_15)


====== Button ================

------------ Reset Button
GPIO: INT_22
Timer: 3(sec)  Action: Reboot
Timer: 6(sec)  Action: Restore Factory


====== Led ===================
SYSTEM
  ON [ASIC(G)]
  OFF [ASIC(G)]
  BLINK [ASIC(G)]
Port
  ON [ASIC(P)]
  ON C2 [ASIC(P)]
  OFF [ASIC(P)]
  AUTO [ASIC(P)]


====== Reset =================
Type: GPIO
GPIO: INT_21


====== WatchDog ==============
Type: REG