Template:Dd-wrt54gs5-6 flash

From TechInfoDepot
Jump to navigationJump to search

Flashing DD-WRT

 

These instructions are for the WRT54gS version v.5, v.5.1 and v.6. NOTE THE S.

IN SPITE OF SOME OTHER INSTRUCTIONS ELSEWHERE, YOU REALLY NEED TO CREATE A CUSTOM VX Image for your router. If you don’t you will get a generic mac address on your router and a generic mac address will mean most ISP won’t let you connect to the internet. Here is how to do it properly

There is good information at the scorpiontek site: http://www.scorpiontek.org/portal/content/view/27/36

Download the zipped files in GV5Flash.zip

Or you can download the same file from me here: Gv5Flash.zip

  1. Read the peacock announcement found here: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
  2. Do a Hard reset or 30/30/30 on the router according to note 1 of the peacock announcement (30/30/30)
  3. Set a static IP on your computer to 192.168.1.7
  4. Connect the lan cable from your computer to a LAN port of your router. Make sure your router is plugged in.
  5. Unzip the file you downloaded and place it in a location you can easily find on your computer
  6. Unzip the VXImgToolGui.zip file to the same folder as where you placed the other files you downloaded
  7. Delete the vxworks_prep_v03.bin file
  8. Go to this location and download the vxworks_prep_GS_v03.bin file: vxworks_prep_gs_v03.zip
  9. Click on the VXImgToolGui.exe program
    • Make sure the top button is on the right for WRT54GS, not the left for WRT54G.
    • Put the mac address from the bottom of your router in the box that says "Desired Mac Address"
    • Click on the three dots next to "output image" and save the file as My54gsImage.bin in the same folder as everything else is located.
  10. Power cycle the router (unplug the power from the router for 30 seconds and then plug it back in)
  11. Open your browser to 192.168.1.1 but putting that in the browser address window of your browser. You should open the linksys webgui and NOT a page that says Management Mode. If you see management mode, power cycle the router again.
  12. Enter "root" as the username and "admin" as the password
  13. Go to administration and firmware upgrade
  14. Navigate to the folder that you are using, and select vxworks_prep_GS_v03.bin
  15. Hit upgrade.
  16. Wait for FIVE FULL MINUTES. Go for a walk. Don't you TOUCH that router for FIVE MINUTES.
  17. When five full earth minutes have passed, power cycle the router
  18. Refresh your browser window. If you get a blank window, clear your browser cache. NOW you should be in the MANAGEMENT MODE window.
  19. Select the My54gImage.bin file that you created. Hit upgrade.
  20. Wait for the "Upgrade Success" message, and then WAIT FIVE FULL MINUTES again. Don't TOUCH your router.
  21. Start tftp.exe
    • Enter 192.168.1.1 as the address in the top box of tftp.exe
    • Leave the password blank
    • Select the 12548 Newd_Micro.bin firmware
    • Set retries to 99.
    • Power cycle the router
    • Count to 2
    • Hit upgrade
  22. When you get a success, wait FIVE FULL minutes.
  23. When you can access the dd-wrt webgui using a browser at 192.168.1.1, power cycle the router.
  24. When you can again access the dd-wrt webgui using a browser at 192.168.1.1, do another Hard reset or 30/30/30 on the router.
  25. Reset your computer ethernet connection to auto IP and auto DNS
  26. Check for recommended builds here.