TP-LINK RE210/Serial info

From TechInfoDepot
Jump to navigationJump to search

Console output

Boot log
U-Boot 1.1.3 (Jun 29 2015 - 14:29:26)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29 
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
============================================ 
Ralink UBoot Version: 4.1.0.0
This UBoot has been rewritten by TPLINK *_*
-------------------------------------------- 
ASIC 7620_MP (Port5<->Phy)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jun 29 2015  Time:14:29:26
============================================ 
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768 

 ##### The CPU freq = 580 MHZ #### 
 estimate memory size =64 Mbytes

Please choose the operation: 
   1: Load system code to SDRAM via TFTP. 
   2: Load system code then write to Flash via TFTP. 
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   6: Load ART data then write to Flash via TFTP.
   7: Load Boot Loader code then write to Flash via Serial. 
   9: Load Boot Loader code then write to Flash via TFTP. 
 0

3: System Boot system code via Flash.
## Booting image at bc020000 ...
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c310) ...
## Giving linux memsize in MB, 64

Starting kernel ...
LINUX started...

 THIS IS ASIC
Linux version 2.6.36+ (canjchen@ubuntu2ccj) 
(gcc version 3.4.2) #2 Mon Jun 29 14:31:06 CST 2015

 The CPU feqenuce set to 580 MHz
 MIPS CPU sleep mode enabled.
 PCIE: bypass PCIe DLL.
 PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
 disable all power about PCIe
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3 
 rw rootfstype=squashfs init=/sbin/init console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0006f7aa
Readback ErrCtl register=0006f7aa
Memory: 62164k/65536k available 
(2016k kernel code, 3372k reserved, 449k data, 144k init, 0k highmem)
NR_IRQS:128
MTK/Ralink System Tick Counter init... cd:80259da8, m:214748, s:32
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 4096 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 1a321d
RALINK_GPIOMODE = 18321d
PPLL_CFG1=0xe64000
MT7620 PPLL lock
PPLL_DRV =0x80080504
start PCIe register access
RALINK_PCI_PCICFG_ADDR = 1000f0

*************** MT7620 PCIe RC mode *************
bio: create slab <bio-0> at 0
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff]
pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff]
pci 0000:01:00.1: BAR 0: set to [mem 0x20100000-0x201fffff] (PCI address [0x20100000-0x201fffff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff]
pci 0000:00:00.0:   bridge window [mem pref disabled]
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 20200000
res[1]->end = 2020ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 200fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20100000
res[0]->end = 201fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
Switching to clocksource Ralink external timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 121
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
Generic platform RAM MTD, (c) 2004 Simtec Electronics
deice id : ef 40 17 0 0 (40170000)
W25Q64BV(ef 40170000) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (0M) 
.erasesize = 0x00000008 (0K) .numeraseregions = 65536

Creating 6 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
NO GPIO Event!
0x000000000000-0x000000020000 : "Bootloader"
0x000000020000-0x000000120000 : "Kernel"
0x000000120000-0x0000007e0000 : "Rootfs"
0x0000007e0000-0x0000007f0000 : "UserConfig"
0x0000007f0000-0x000000800000 : "ART_Data"
SMACCR1 -- : 0x0000ec08
SMACCR0 -- : 0x6b2c02a0
Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
SMACCR1 -- : 0x0000ec08
SMACCR0 -- : 0x6b2c02a0
PROC INIT OK!
PPP generic driver version 2.4.2
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 144k freed
init started:  BusyBox v1.01 (2015.06.29-06:32+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
Raeth v3.0 (Tasklet,SkbRecycle)

phy_tx_ring = 0x03ee2000, tx_ring = 0xa3ee2000
phy_rx_ring0 = 0x03ee3000, rx_ring0 = 0xa3ee3000
SMACCR1 -- : 0x0000ec08
SMACCR0 -- : 0x6b2c02a0
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20010000
This Board use 2.6.36.x
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
nf_conntrack version 0.5.0 (973 buckets, 5120 max)
Netfilter messages via NETLINK v0.30.
ctnetlink v0.93: registering with nfnetlink.

 (none) mips #2 Mon Jun 29 14:31:06 CST 2015 (none)
(none) login: device eth2.1 entered promiscuous mode
device eth2 entered promiscuous mode
br0: port 1(eth2.1) entering forwarding state
br0: port 1(eth2.1) entering forwarding state
Lan Domain: tplinkrepeater.net
Lan Domain: www.tplinkrepeater.net
rt2860v2_ap: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
MT7620-->

=== pAd = c09b1000, size = 907424 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
MT7620-->AP Driver version-2.7.1.6_edcca_monitor_20131227
MT7610-->register rtpci
MT7610-->

=== pAd = c1002000, size = 934536 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
MT7610-->pAd->CSRBaseAddress =0xc0f00000, csr_addr=0xc0f00000!
MT7610-->device_id =0x7650
MT7610-->==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002
MT7610-->MACVersion = 0x76502000
MT7620-->RX DESC a3097000  size = 2048