Sagemcom F@ST 3764/Serial info

From TechInfoDepot
Jump to navigationJump to search

Boot log

bootlog • >>
SAGEM Secure-boot SU2_2_1 fast_3764

CPU: IKANOS Fusiv 180 Family
PCI:   33 MHz
DRAM:  128 MB
Flash: 32 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   emac2

Marvell 88e6161 initialized as hub
MCU awaken (22)
MCU v.8 initialized 9600bps on port 2
emac2

Permanent parameters are programmed but not activated : skip DSA signature
Potential firmware found at address : bf080000
half-flash parsed !
Potential firmware found at address : be000000
Found 2 firmwares !
Searching valid operational firmware
Operational Firmware found with no key at address be000000
good regular firmware at @0xBE000000 with key @0x00000000
No bootloader arg
partition not moved
updating kernel args
bootargs root=/dev/mtdblock6 ro rootfstype=squashfs operational_start=0xbe000000 
rescue_start=0xbf080000 myfs_start=0xbe940000 type=operational image_addr=0xBE000000
kernel args update done
Launch regular code from flash
alarmLEDMode(E_FLASH)!
bootm BE000140
## Booting image at be000140 ...
   Image Name:   TPSA_v8058.img
   Created:      2011-08-10   9:44:06 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    9577942 Bytes =  9.1 MB
   Load Address: 80010000
   Entry Point:  802e5000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.16.26 #1 Wed Aug 10 10:44:02 CET 2011
argc 9 arg <NULL> env memsize=128
memsize  board_memsize = 128
env memsize=128
env initrd_start=0xA0000000
env initrd_size=0x0
flash_start be000000
env flash_start=0xBE000000
board_flash_size 2000000
env flash_size=0x2000000
arg[1] root=/dev/mtdblock6
arg[2] ro
arg[3] rootfstype=squashfs
arg[4] operational_start=0xbe000000
arg[5] rescue_start=0xbf080000
arg[6] myfs_start=0xbe940000
arg[7] type=operational
arg[8] image_addr=0xBE000000

CPU revision is: 0001964c
Determined physical RAM map:
 memory: 07800000 @ 00000000 (usable)
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock6 ro rootfstype=squashfs 
operational_start=0xbe000000 rescue_start=0xbf080000 myfs_start=0xbe940000 
type=operational image_addr=0xBE000000
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 512 (order: 9, 8192 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 109752k/122880k available (2368k kernel code, 
12992k reserved, 527k data, 132k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
NET: Registered protocol family 16
Fusiv PCI: starting...
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
fs/cramfs_block_uncompressed created
NTFS driver 2.1.26 [Flags: R/O].
08x, <6>Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered

Random: 0x849a9548
Serial: 8250/16550 driver $Revision: 1.9.6.1 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO map 0xb9020000 mem 0xb9020000 (irq = 6) is a 16450
serial8250: ttyS1 at MMIO map 0xb90a0000 mem 0xb90a0000 (irq = 29) is a 16450
ikf68xx-ehci-hcd ikf68xx-ehci-hcd.0: Ikanos On-Chip EHCI Host Controller
ikf68xx-ehci-hcd ikf68xx-ehci-hcd.0: new USB bus registered, assigned bus number 1
ikf68xx-ehci-hcd ikf68xx-ehci-hcd.0: irq 35, io mem 0x19230000
ikf68xx-ehci-hcd ikf68xx-ehci-hcd.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ikf68xx-ohci-hcd ikf68xx-ohci-hcd.0: Ikanos On-Chip OHCI Host Controller
ikf68xx-ohci-hcd ikf68xx-ohci-hcd.0: new USB bus registered, assigned bus number 2
ikf68xx-ohci-hcd ikf68xx-ohci-hcd.0: irq 35, io mem 0x19240800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
/home/G545662/37XX/SRC/1.0.5_RC1/checkoutdir/openrg/package/rg/os/linux-2.6/
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
u32 classifier
    OLD policer on
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
NET: Registered protocol family 1
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.5
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.7
Bluetooth: BNEP (Ethernet Emulation) ver 1.2
Bluetooth: BNEP filters: protocol multicast
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
openrg_flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
openrg_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 1 MTD partitions on "openrg_flash":
0x00000000-0x02000000 : "openrg"
openrg_flash: detected at 0x1e000000 size 33554432 bytes
Freeing unused kernel memory: 132k freed
Version: 4.9.4.TPSA_v8058
Platform: Sagem 376X GE
Compilation Time: 10-Aug-11 09:31:28
Tag: NRD_?bldorg?rg_liveboxPro-V3_0-0-1
Compilation Flags: SOUCHE_DEVICE_DISCOVERY=y CONFIG_TELEFONICA=y CONFIG_VDSL=y CONFIG_ROUTING_WITH_DSPRULES=y CONFIG_37xx_STANDARD=y CONFIG_RGCONF_MIGRATION=y CONFIG_SOUCHE_RECONF=y CONFIG_RG_DB_SEMAPHORE=y CONFIG_SAGEM_DB_ACCESS=y CONFIG_DEFAULT_RGCONF_TELNET=y CONFIG_RG_TELNETS=y CONFIG_SAGEM_IPPRINT=y CONFIG_USB_PRINTER=y CONFIG_HFS_FS=y CONFIG_HFSPLUS_FS=y CONFIG_SAGEM_WIFI_MODE_11N=y CONFIG_LIVEBOX_VOIP=y CONFIG_LOG_ENTITIES=0 CONFIG_KALLSYMS=y CONFIG_RG_GDBSERVER=y CONFIG_LIVEBOX_TV=y CONFIG_SOUCHE_USE_EXTERNAL_OPENSSL=y DIST=SAGEM_376X CONFIG_TPSA=y CONFIG_INTERNAL_FIRMWARE_VERSION=1.1.0.5 CONFIG_FIRMWARE_VERSION=TPSA_v8058 LIC=../../../license/jpkg_ikanos_vx.lic
User Information: G545662@sst-ESPRIMO-P2760 /home/G545662/37XX/SRC/1.0.5_RC1/checkoutdir/openrg/package/rg
############### xdsl_mode = 1 ######################
###### Kernel Debug mode (rg_conf/kernel/debug) = 0 ######
ADSL LED controlled by interface eth2
WAN LED controlled by interface ppp0

insmod: add-symbol-file build/debug/hard_watchdog_module.o 0xc0004000 -s .data 0xc0005800 -s .bss 0xc0005940

HardwareWatchdogInitialize : NORMAL BOOT

HardwareWatchdogInitialize :: --- WATCHDOG -- INITIALIZED with ED72 value (i.e. 5999ms)
HardwareWatchdogInitialize :: --- WATCHDOG -- Pacify timer of 2000 ms STARTED

insmod: add-symbol-file build/debug/be_pppoa_mod.o 0xc0007000 -s .data 0xc00086e0 -s .bss 0xc0008840

insmod: add-symbol-file build/debug/fusivlib.o 0xc0022000 -s .data 0xc002eaf0 -s .bss 0xc0030e80
fusiv library initializing...
Buffer Copy Through DMA is enabled

fusiv library initialized SUCCESSFULLY...

insmod: add-symbol-file build/debug/bus_arbiter_lkm.o 0xc000a000 -s .data 0xc000b380 -s .bss 0xc000b4e0
vox bus arbiter interrupt handlers registered

insmod: add-symbol-file build/debug/opensrc_lkm.o 0xc0002000 -s .data 0xc00026d0 -s .bss 0xc0002820

insmod: add-symbol-file build/debug/bm.o 0xc0014000 -s .data 0xc0017170 -s .bss 0xc0017340

 Buffer Manager is initializing...
BMU GIGE clock
Slave Mem Alloc: Req size 16   Ptr2Block 0x191f0000
Load into BM APU Successful !!!

 Buffer Manager initialized SUCCESSFULLY...

insmod: add-symbol-file build/debug/sysutil.o 0xc0019000 -s .data 0xc001c0c0 -s .bss 0xc001c220

insmod: add-symbol-file build/debug/timerlib.o 0xc0010000 -s .data 0xc0010dc0 -s .bss 0xc0010f20
Timers are getting initalized
Timers are initilized SUCCESSFULLY...

insmod: add-symbol-file build/debug/ethdriver.o 0xc0044000 -s .data 0xc004baf0 -s .bss 0xc004e8c0
Module params: eth0_mii=0   eth1_mii=0
eth0: Netpro Sierra Ethernet found at 0xb9110000, irq 14
GIGE 1 clock dev->baseAddr b9110000
Slave Mem Alloc: Req size 16   Ptr2Block 0x191f0010
eth1: Netpro Sierra Ethernet found at 0xb9150000, irq 13
GIGE 2 clock dev->baseAddr b9150000
Slave Mem Alloc: Req size 16   Ptr2Block 0x191f0020
eth0 interface configured in GMII mode

Ethernet Driver is initialized SUCCESSFULLY
eth1 interface configured in GMII mode

insmod: add-symbol-file build/debug/vdsldriver_lkm.o 0xc003c000 -s .data 0xc003f9e0 -s .bss 0xc0040ec0
VDSL AP and VDSL PHY  clocks are enabled
eth2: Netpro VDSL Ethernet found at 0x0, irq 36
>>> bmChangeMacList currNumConfiguredMacAddrs = 0 MAX_NUM_SUPPORTED_MAC_ADDRESSES = 4
0x0:0x1:0x2:0x3:0x4:0x7
User parameters for VDSL AP configured successfully
Slave Mem Alloc: Req size 16   Ptr2Block 0x191f0030
VDSL AP started successfully

VDSL Driver is initialized SUCCESSFULLY

insmod: add-symbol-file build/debug/periap.o 0xc0050000 -s .data 0xc0051c20 -s .bss 0xc0053c60
periApDriverInit: doneSlave Mem Alloc: Req size 16   Ptr2Block 0x191f0040

 *******LOAD firmware to AP:PERI_ID result:0Load into PERI_AP APU Successful !!!

insmod: add-symbol-file build/debug/ath_hal.o 0xc00e1000 -s .data 0xc014e550 -s .bss 0xc0158e80
ath_hal: 0.9.14.25 (AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, DEBUG, REGOPS_FUNC)

insmod: add-symbol-file build/debug/wlan.o 0xc015c000 -s .data 0xc0199b20 -s .bss 0xc019a200
wlan: 0.8.4.2 (Atheros/multi-bss)

insmod: add-symbol-file build/debug/ath_rate_atheros.o 0xc0066000 -s .data 0xc006b970 -s .bss 0xc0074440
ath_rate_atheros: Version 2.0.1
Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved

insmod: add-symbol-file build/debug/ath_dfs.o 0xc0076000 -s .data 0xc007ec00 -s .bss 0xc007ed80
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved

insmod: add-symbol-file build/debug/wlan_wep.o 0xc000d000 -s .data 0xc000e800 -s .bss 0xc000e940

insmod: add-symbol-file build/debug/wlan_tkip.o 0xc0055000 -s .data 0xc00583c0 -s .bss 0xc0058500

insmod: add-symbol-file build/debug/wlan_ccmp.o 0xc001e000 -s .data 0xc00201e0 -s .bss 0xc0020320

insmod: add-symbol-file build/debug/wlan_xauth.o 0xc0033000 -s .data 0xc0033300 -s .bss 0xc0033440

insmod: add-symbol-file build/debug/wlan_acl.o 0xc0038000 -s .data 0xc0039010 -s .bss 0xc0039160
wlan: mac acl policy registered

insmod: add-symbol-file build/debug/ath_pci.o 0xc019c000 -s .data 0xc01c7730 -s .bss 0xc01c8320
ath_pci: 0.9.4.5 (Atheros/multi-bss)
ath_pci: CR-LSDK-1.3.1.110
PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
Chan  Freq  RegPwr  HT   CTL CTL_U CTL_L DFS
   1  2412n     20  HT20  1    0    1     N
   1  2412n     20  HT40  1    0    1     N
   2  2417n     20  HT40  1    0    1     N
   3  2422n     20  HT40  1    1    1     N
   4  2427n     20  HT40  1    1    1     N
   5  2432n     20  HT40  1    1    1     N
   6  2437n     20  HT40  1    1    1     N
   7  2442n     20  HT40  1    1    1     N
   8  2447n     20  HT40  1    1    1     N
   9  2452n     20  HT40  1    1    1     N
  10  2457n     20  HT40  1    1    1     N
  11  2462n     20  HT40  1    1    1     N
  12  2467n     20  HT40  1    1    0     N
  13  2472n     20  HT40  1    1    0     N
dfs_init_radar_filters: dfs->dfs_rinfo.rn_numradars: 0
DFS min filter rssiThresh = 21
DFS max pulse dur = 131 ticks
wifi0: 11ng rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11ng MCS:  0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
wifi0: mac 384.2 phy 15.15 radio 12.0
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Use hw queue 7 for UAPSD
wifi0: Atheros 9287: mem=0x1a000000, irq=25 hw_base=0xba000000

insmod: add-symbol-file build/debug/one_module.o 0xc0249000 -s 
.main_flow 0xc02856c0 -s .data 0xc02a4e50 -s .bss 0xc02a6ce0
Loading license 2e7cce03ae1ecdf8664e2a9d4237505fb4b92a03b3c702e282dad8703897fb79647f254aad168a0000
42689d4bbeae320ee12b21d44036dba65548ebd421923317a5e6fd3f30792f5c8c58b63fbb65f614a9b3010287.SAGEM
loading license key: SAGEM
loading license key: SAGEM

insmod: add-symbol-file build/debug/kleds_mod.o 0xc0035000 -s .data 0xc00364c0 -s .bss 0xc0036640

insmod: add-symbol-file build/debug/lb_jffs_mod.o 0xc0042000 -s .data 0xc0042200 -s .bss 0xc0042360
Creating 1 MTD partitions on "openrg_flash":
0x01b00000-0x02000000 : "jffs2"
Press ESC to enter BOOT MENU mode.
dd_openrg_init: registering openrg device discovery entity
MAPS:
00400000-007d5000 r-xp 00000000 00:09 861352     /mnt/cramfs/bin/openrg
10000000-1006d000 rw-p 003d5000 00:09 861352     /mnt/cramfs/bin/openrg
1006d000-10091000 rwxp 1006d000 00:00 0          [heap]
2aaa8000-2aaae000 r-xp 00000000 00:09 5203032    /mnt/cramfs/lib/ld-uClibc.so.0
2aaae000-2aaaf000 rw-p 2aaae000
insmod: add-symbol-file build/debug/wlan_scan_ap.o 0xc0080000 -s .data 0xc0083910 -s .bss 0xc0083a60
00:00 0
2aab0000-2aab1000 rw-p 2aab0000 00:00 0
2aab2000-2aab3000 rw-s 00000000 00:06 0          /SYSV0000162e (deleted)
2aab4000-2aab5000 rw-s 00000000 00:06 32769      /SYSV0000162d (deleted)
2aaed000-2aaee000 rw-p 00005000 00:09 5203032    /mnt/cramfs/lib/ld-uClibc.so.0
2aaee000-2ab03000 r-xp 00000000 00:09 6258740    /mnt/cramfs/lib/libopenrg.so
2ab03000-2ab43000 ---p 2ab03000
insmod: add-symbol-file build/debug/hw_qos_ikanos_mod.o 0xc0060000 -s .data 0xc0060900 -s .bss 0xc0060a80
 00:00 0
2ab43000-2ab44000 rw-p 00015000 00:09 6258740    /mnt/cramfs/lib/libopenrg.so
2ab44000-2ab81000 r-xp 00000000 00:09 5975448    /mnt/cramfs/lib/libjutil.shw_qos_init:183      init module
o
2ab81000-2abc1000 ---p 2ab81000 00:00 0
2abc1000-2abc6000 rw-p 0003d000 00:09 5975448    /mnt/cramfs/lib/libjutil.so
2abc6000-2abcc000 rw-p 2abc6000 00:00 0
2abcc000-2ac0a000 r-xp 00000000 00:09 6343272    /mnt/cramfs/lib/libssl.so.0.9.8
2ac0a000-2ac49000 ---p 2ac0a000 00:00 0
2ac49000-2ac4d000 rw-p 0003d000 00:09 6343272    /mnt/cramfs/lib/libssl.so.0.9.8
2ac4d000-2ad8f000 r-xp 00000000 00:09 5439004    /mnt/cramfs/lib
insmod: add-symbol-file build/debug/igmp_proxy_mod.o 0xc0090000 -s .data 0xc0096ef0 -s .bss 0xc0097040
/libcrypto.so.0.9.8
2ad8f000-2adce000 ---p 2ad8f000 00:00 0
2adce000-2ade4000 rw-p 00141000 00:09 5439004    /mnt/cramfs/lib/libcrypto.so.0.9.8
2ade4000-2ade7000 rw-p 2ade4000 00:00 0
2ade7000-2adea000 r-xp 00000000 00:09 5906848    /mnt/cramfs/lib/libdl.so.0
2adea000-2ae29000 ---p 2adea000 00:00 0
2ae29000-2ae2a000 rw-p 00002000 00:09 5906848    /mnt/cramfs/lib/libdl.so.0
2ae2a000-2ae3f000 r-xp 00000000 00:09 6313776    /mnt/cramfs/lib/librg_config.so
2ae3f000-2ae7e000 ---p 2ae3f000 00:00 0
2ae7e000-2ae81000 rw-p 00014000 00:09 6313776    /m
insmod: add-symbol-file build/debug/rg_usfs.o 0xc0085000 -s .data 0xc0086500 -s .bss 0xc0086680
nt/cramfs/lib/librg_config.so
2ae81000-2aeaf000 r-xp 00000000 00:09 6061520    /mnt/cramfs/lib/libm.so.0
2aeaf000-2aeef000 ---p 2aeaf000 00:00 0
2aeef000-2aef0000 rw-p 0002e000 00:09 6061520    /mnt/cramfs/lib/libm.so.0
2aef0000-2aef2000 r-xp 00000000 00:09 6511232    /mnt/cramfs/lib/libutil.so.0
2aef2000-2af31000 ---p 2aef2000 00:00 0
2af31000-2af32000 rw-p 00001000 00:09 6511232    /mnt/cramfs/lib/libutil.so.0
2af3
insmod: add-symbol-file build/debug/tcp_mss.o 0xc0000000 -s .data 0xc0000a00 -s .bss 0xc0000b80
2000-2af73000 r-xp 00000000 00:09 5227592    /mnt/cramfs/lib/libSwitch.so
2af73000-2afb2000 ---p 2af73000 00:00 0
2afb2000-2afb3000 rw-p 00040000 00:09 5227592    /mnt/cramfs/lib/libSwitch.so
2afb3000-2afbd000 r-xp 00000000 00:09 6090768    /mnt/cramfs/lib/libmsg-api.so
2afbd000-2affc000 ---p 2afbd000 00:00 0
2affc000-2affd000 rw-p 00009000 00:09 6090768    /mnt/cramfs/lib/libmsg-api.so
2affd00
insmod: add-symbol-file build/debug/rg_dhcp_pktfil.o 0xc0088000 -s .data 0xc0089440 -s .bss 0xc00895c0
0-2b00a000 rw-p 2affd000 00:00 0
2b00a000-2b01b000 r-xp 00000000 00:09 6297412    /mnt/cramfs/lib/libpthread.so.0
2b01b000-2b05a000 ---p 2b01b000 00:00 0
2b05a000-2b05f000 rw-p 00010000 00:09 6297412    /mnt/cramfs/lib/libpthread.so.0
2b05f000-2b061000 rw-p 2b05f000 00:00 0
2b061000-2b064000 r-xp 00000000 00:09 6501972    /mnt/cramfs/lib/libtr69If.so
2b064000-2b0a3000 ---p 2b064000 0
insmod: add-symbol-file build/debug/rg_ipv4.o 0xc0064000 -s .data 0xc0064440 -s .bss 0xc00645c0
0:00 0
2b0a3000-2b0a4000 rw-p 00002000 00:09 6501972    /mnt/cramfs/lib/libtr69If.so
2b0a4000-2b149000 r-xp 00000000 00:09 5296460    /mnt/cramfs/lib/libIPV4 device driver registered
c.so.0
2b149000-2b189000 ---p 2b149000 00:00 0
2b189000-2b18b000 rw-p 000a5000 00:09 5296460    /mnt/cramfs/lib/libc.so.0
2b18b000-2b18f000 rw-p 2b18b000 00:00 0
2b18f000-2b19d000 r-xp 00000000 00:09 5947060    /mnt/cramfs/lib/libgcc_s.so.1
2b19d000-2b1dd000 ---p 2b19d000 00:00 0
2b1dd000-2b1de0
insmod: add-symbol-file build/debug/pppoe_relay.o 0xc009f000 -s .data 0xc00a2670 -s .bss 0xc00a27c0
00 rw-p 0000e000 00:09 5947060    /mnt/cramfs/lib/libgcc_s.so.1
2b1de000-2b3de000 rw-p 2b1de000 00:00 0
7fe71000-7fe86000 rwxp 7fe71000 00:00 0          [stack]

insmod: add-symbol-file build/debug/rg_pppoe_relay.o 0xc0062000 -s .data 0xc0062da0 -s .bss 0xc0062f20

insmod: add-symbol-file build/debug/ife6DriverLoad_mod.o 0xc008d000 -s .data 0xc008d440 -s .bss 0xc008d5c0
Initializing IFE6 Driver Load module

insmod: add-symbol-file build/debug/btn.o 0xc008b000 -s .data 0xc008bc20 -s .bss 0xc008bdc0

insmod: add!!!

DSP Ver No:1.1
 Initialization SLIC system
 Initializing Voice
slic GPIO is 7
Initializing SPI Module
SAGEM SLIC card as SILABS
Initializing SLICs
LOAD Si3226 PATCH for Rev C
Si3226 patch version 0X06102008
Patch loaded successfully channel 0
Patch loaded successfully channel 1
MDAC Calibration for channel 0
MDAC Calibration for channel 1
other Calibration
Activate SLICs => 2

# DSP Voice Module Part 2 Loading Ok
##################################################

insmod: add-symbol-file build/debug/rtp.o 0xc00cd000 -s .data 0xc00d7d00 -s .bss 0xc00d87c0

##################################################
# RTP Stack Module Loading ...

Register /dev/rtp Device ...Register /sys/sagem/rtp SysCtl ...
 insmod: cannot open module `/lib/modules/relay.o': No such file or directory
 Permanent Parameters were stored in Rgconf RAM

__BEI:config_xdsl_mode:xdslmode=1,autodetect=2__

__BEI:VDSL config_xdsl_mode:xdslmode=1,autodetect=2__
wifi_init: Atheros Wifi card: device AR5416_DEVID_AR9287_PCI (Kiwi).
Atheros Wifi card found: ath0
wlanconfig: ioctl: No such device
mt_ma_open : entering in -------------------
mt_ma_start_process : entering in -------------------
opening reconfentity Entity

MAIN AUTOM ID IS 345 warning #1 :new rg_conf entry but not signaled
warning #1 :new rg_conf entry but not signaled
warning #1 :new rg_conf entry but not signaled
warning #1 :new rg_conf entry but not signaled
warning #1 :new rg_conf entry but not signaled
warning #1 :new rg_conf entry but not signaled
warning #1 :new rg_conf entry but not signaled
warning #1 :new rg_conf entry but not signaled
------>dev_if_notify : <eth1> [0 -> 1]
------>dev_if_notify : <eth1.1> [0 -> 1]
------>dev_if_notify : <br0> [0 -> 1]
------>dev_if_notify : <eth0> [0 -> 1]
------>dev_if_notify : <wifi0> [0 -> 1]
------>dev_if_notify : <ath0> [0 -> 1]
------>dev_if_notify : <eth2> [0 -> 1]
------>dev_if_notify : <eth2.35> [0 -> 1]
------>dev_if_notify : <eth2.838> [0 -> 1]
------>dev_if_notify : <eth2.839> [0 -> 1]
------>dev_if_notify : <eth0.35> [0 -> 1]
------>dev_if_notify : <eth0.838> [0 -> 1]
------>dev_if_notify : <eth0.839> [0 -> 1]
------>dev_if_notify : <eth1.839> [0 -> 1]
------>dev_if_notify : <dsl0> [0 -> 1]
------>dev_if_notify : <ethoa0> [0 -> 1]
------>dev_if_notify : <ethoa1> [0 -> 1]
------>dev_if_notify : <br1> [0 -> 1]
------>dev_if_notify : <ppp0> [0 -> 1]
------>dev_if_notify : <ppp1> [0 -> 1]
------>dev_if_notify : <br0> [1 -> 2]
------>dev_if_notify : <br0> [2 -> 3]
------>dev_if_notify : <br0> [3 -> 4]
OS: VDSL daemon already running
Access: Failed to open bme module
------>dev_if_notify : <eth0> [1 -> 2]
------>dev_if_notify : <eth0> [2 -> 3]
------>dev_if_notify : <eth0> [3 -> 4]
------>dev_if_notify : <eth1> [1 -> 2]
------>dev_if_notify : <eth1> [2 -> 3]
------>dev_if_notify : <eth1> [3 -> 4]
------>dev_if_notify : <wifi0> [1 -> 2]
------>dev_if_notify : <wifi0> [2 -> 3]
------>dev_if_notify : <wifi0> [3 -> 4]
------>dev_if_notify : <ath0> [1 -> 2]
 Unset HTIE 11n in beacon
<6>ar9287EepromSetPowerPerRateTable: Reg power: 20 dBm Net ant gain allowed: 0 dB
ar9287EepromSetPowerPerRateTable: Power Limit (Reg power - Net ant gain): 20 dBm
ar9287EepromSetPowerPerRateTable: Number of chains: 2 Per chain power limit: 17 dBm
ar9287EepromSetPowerPerRateTable: Target powers: 1Mb/s: 15 dBm 11Mb/s: 15 dBm 6Mb/s: 15 dBm 54Mb/s: 12 dBm 
MCS0(HT20): 15 dBm MCS7(HT20): 10 dBm MCS0(HT40): 0 dBm MCS7(HT40): 0 dBm
ar9287EepromSetPowerPerRateTable: syn 2412 ctl 2412 ext 2412 is40 0
ar9287EepromSetPowerPerRateTable: Ctl mode: 1 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Ctl mode: 2 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Ctl mode: 5 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Chosen powers:1Mb/s: 15 dBm 11Mb/s: 15 dBm 6Mb/s: 15 dBm 54Mb/s: 12 dBm 
MCS0(HT20): 15 dBm MCS7(HT20): 10 dBm MCS0(HT40): 0 dBm MCS7(HT40): 0 dBm
2xMaxPowerLevel: 37 (LEG)
ar9287EepromSetPowerPerRateTable: Reg power: 20 dBm Net ant gain allowed: 0 dB
ar9287EepromSetPowerPerRateTable: Power Limit (Reg power - Net ant gain): 19 dBm
ar9287EepromSetPowerPerRateTable: Number of chains: 2 Per chain power limit: 16 dBm
ar9287EepromSetPowerPerRateTable: Target powers: 1Mb/s: 15 dBm 11Mb/s: 15 dBm 6Mb/s: 15 dBm 54Mb/s: 12 dBm 
MCS0(HT20): 15 dBm MCS7(HT20): 10 dBm MCS0(HT40): 0 dBm MCS7(HT40): 0 dBm
ar9287EepromSetPowerPerRateTable: syn 2412 ctl 2412 ext 2412 is40 0
ar9287EepromSetPowerPerRateTable: Ctl mode: 1 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Ctl mode: 2 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Ctl mode: 5 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Chosen powers:1Mb/s: 15 dBm 11Mb/s: 15 dBm 6Mb/s: 15 dBm 54Mb/s: 12 dBm 
MCS0(HT20): 15 dBm MCS7(HT20): 10 dBm MCS0(HT40): 0 dBm MCS7(HT40): 0 dBm
2xMaxPowerLevel: 37 (LEG)

JXU: set the rxBufsize to 3851
ath_newstate: Resetting VAP dfswait_run
ath_newstate: Resetting VAP dfswait_run
ar9287EepromSetPowerPerRateTable: Reg power: 20 dBm Net ant gain allowed: 0 dB
ar9287EepromSetPowerPerRateTable: Power Limit (Reg power - Net ant gain): 19 dBm
ar9287EepromSetPowerPerRateTable: Number of chains: 2 Per chain power limit: 16 dBm
ar9287EepromSetPowerPerRateTable: Target powers: 1Mb/s: 15 dBm 11Mb/s: 15 dBm 6Mb/s: 15 dBm 54Mb/s: 12 dBm 
MCS0(HT20): 15 dBm MCS7(HT20): 10 dBm MCS0(HT40): 0 dBm MCS7(HT40): 0 dBm
ar9287EepromSetPowerPerRateTable: syn 2457 ctl 2457 ext 2457 is40 0
ar9287EepromSetPowerPerRateTable: Ctl mode: 1 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Ctl mode: 2 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Ctl mode: 5 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Chosen powers:1Mb/s: 15 dBm 11Mb/s: 15 dBm 6Mb/s: 15 dBm 54Mb/s: 12 dBm 
MCS0(HT20): 15 dBm MCS7(HT20): 10 dBm MCS0(HT40): 0 dBm MCS7(HT40): 0 dBm
2xMaxPowerLevel: 37 (LEG)
ath_chan_set: Changing to channel 2457, Flags 30080, PF 0

JXU: set the rxBufsize to 3851
device ath0 entered promiscuous mode
------>dev_if_notify : <ath0> [2 -> 3]
------>dev_if_notify : <ath0> [3 -> 4]
------>dev_if_notify : <eth2.35> [1 -> 2]
eth2.35: Setting MAC address to  94 fe f4 a9 75 83.
device eth2 entered promiscuous mode
VLAN (eth2.35):  Setting underlying device (eth2) to promiscious mode.
------>dev_if_notify : <eth2.838> [1 -> 2]
eth2.838: Setting MAC address to  94 fe f4 a9 75 84.
------>dev_if_notify : <eth2.839> [1 -> 2]
eth2.839: Setting MAC address to  94 fe f4 a9 75 85.
------>dev_if_notify : <eth2> [1 -> 2]
------>dev_if_notify : <eth1.1> [1 -> 2]
eth1.1: Setting MAC address to  94 fe f4 a9 75 82.
VLAN (eth1.1):  Underlying device (eth1) has same MAC, not checking promiscious mode.
eth1.1: Setting MAC address to  94 fe f4 a9 75 82.
VLAN (eth1.1):  Underlying device (eth1) has same MAC, not checking promiscious mode.
eth1.1: dev_set_promiscuity(master, 1)
device eth1 entered promiscuous mode
device eth1.1 entered promiscuous mode
------>dev_if_notify : <eth1.1> [2 -> 3]
------>dev_if_notify : <eth1.1> [3 -> 4]
------>dev_if_notify : <eth1.839> [1 -> 2]
eth1.839: Setting MAC address to  94 fe f4 a9 75 82.
VLAN (eth1.839):  Underlying device (eth1) has same MAC, not checking promiscious mode.
eth1.839: Setting MAC address to  94 fe f4 a9 75 82.
VLAN (eth1.839):  Underlying device (eth1) has same MAC, not checking promiscious mode.
eth1.839: dev_set_promiscuity(master, 1)
------>dev_if_notify : <eth1.839> [2 -> 3]
------>dev_if_notify : <eth1.839> [3 -> 4]
------>dev_if_notify : <br1> [1 -> 2]
------>dev_if_notify : <br1> [2 -> 3]
------>dev_if_notify : <br1> [3 -> 4]
------>dev_if_notify : <ppp0> [1 -> 2]

__BEI:load_rgconf_switch_config called__

__BEI:sg_switch_check_config called__

__BEI:sg_switch_write_config_files called__

__BEI:sg_switch_parse_config called__

__BEI:sg_switch_set_mode called__

__BEI:sg_switch_run_config called__
../../common/MasterControl/Info.cpp(188):Read WSC Config File:/etc/wsc_config.txt
../../common/MasterControl/Info.cpp(1529):Use eth0 address 94:fe:f4:a9:75:81
../../common/MasterControl/Info.cpp(188):Read WSC Config File:/etc/wsc_config.txt
../../common/MasterControl/Info.cpp(1529):Use eth0 address 94:fe:f4:a9:75:81
../../common/MasterControl/MasterControl.cpp(2832):Generated devPwd: 29757909
../../common/WscCmd/WscCmd.cpp(1808):WscCmd::AP tmp file =cp /etc/template.conf
../../common/WscCmd/WscCmd.cpp(1814):WscCmd::AP Config file copied: cmd=cp /etc/template.conf /etc/hostapd.conf
../../common/WscCmd/WscCmd.cpp(2002):WscCmd::Params added to AP config file
ni->ni_vap->iv_opmode = 6
ni->ni_vap->iv_opmode = 6
ar9287EepromSetPowerPerRateTable: Reg power: 20 dBm Net ant gain allowed: 0 dB
ar9287EepromSetPowerPerRateTable: Power Limit (Reg power - Net ant gain): 19 dBm
ar9287EepromSetPowerPerRateTable: Number of chains: 2 Per chain power limit: 16 dBm
ar9287EepromSetPowerPerRateTable: Target powers: 1Mb/s: 15 dBm 11Mb/s: 15 dBm 6Mb/s: 15 dBm 54Mb/s: 12 dBm 
MCS0(HT20): 15 dBm MCS7(HT20): 10 dBm MCS0(HT40): 0 dBm MCS7(HT40): 0 dBm
ar9287EepromSetPowerPerRateTable: syn 2457 ctl 2457 ext 2457 is40 0
ar9287EepromSetPowerPerRateTable: Ctl mode: 1 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Ctl mode: 2 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Ctl mode: 5 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Chosen powers:1Mb/s: 15 dBm 11Mb/s: 15 dBm 6Mb/s: 15 dBm 54Mb/s: 12 dBm 
MCS0(HT20): 15 dBm MCS7(HT20): 10 dBm MCS0(HT40): 0 dBm MCS7(HT40): 0 dBm
2xMaxPowerLevel: 37 (LEG)

JXU: set the rxBufsize to 3851
ath_newstate: Resetting VAP dfswait_run
ath_newstate: Resetting VAP dfswait_run
ar9287EepromSetPowerPerRateTable: Reg power: 20 dBm Net ant gain allowed: 0 dB
ar9287EepromSetPowerPerRateTable: Power Limit (Reg power - Net ant gain): 19 dBm
ar9287EepromSetPowerPerRateTable: Number of chains: 2 Per chain power limit: 16 dBm
ar9287EepromSetPowerPerRateTable: Target powers: 1Mb/s: 15 dBm 11Mb/s: 15 dBm 6Mb/s: 15 dBm 54Mb/s: 12 dBm 
MCS0(HT20): 15 dBm MCS7(HT20): 10 dBm MCS0(HT40): 0 dBm MCS7(HT40): 0 dBm
ar9287EepromSetPowerPerRateTable: syn 2457 ctl 2457 ext 2457 is40 0
ar9287EepromSetPowerPerRateTable: Ctl mode: 1 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Ctl mode: 2 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Ctl mode: 5 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Chosen powers:1Mb/s: 15 dBm 11Mb/s: 15 dBm 6Mb/s: 15 dBm 54Mb/s: 12 dBm 
MCS0(HT20): 15 dBm MCS7(HT20): 10 dBm MCS0(HT40): 0 dBm MCS7(HT40): 0 dBm
2xMaxPowerLevel: 37 (LEG)
ath_chan_set: Changing to channel 2457, Flags 30080, PF 0

JXU: set the rxBufsize to 3851
 key_alloc_2pair: sc_splitmic SET to 1
../../common/InbWlan/InbWlan.cpp(244):UDP recv m_recvPort[0]= 1026
 key_alloc_2pair: sc_splitmic SET to 1

__BEI:sg_switch_free_switch_config called__
------>dev_if_notify : <eth0> [4 -> 1]
------>dev_if_notify : <eth0.35> [1 -> 1]
------>dev_if_notify : <eth0.838> [1 -> 1]
------>dev_if_notify : <eth0.839> [1 -> 1]
Username: ../../common/UPnPDevLib/UPnPMicroStack.c(2689):HTTP receive GET
../../common/UPnPDevLib/UPnPMicroStack.c(2696):HTTP receive /
../../common/UPnPDevLib/UPnPMicroStack.c(2689):HTTP receive GET
../../common/UPnPDevLib/UPnPMicroStack.c(2696):HTTP receive /
../../common/UPnPDevLib/UPnPMicroStack.c(2689):HTTP receive GET
../../common/UPnPDevLib/UPnPMicroStack.c(2696):HTTP receive /
../../common/UPnPDevLib/UPnPMicroStack.c(2689):HTTP receive GET
../../common/UPnPDevLib/UPnPMicroStack.c(2696):HTTP receive /

 xdsl autodetect mode non actif

CPE start address is a7800000

ipos system initialized

BME 1 is coming up
msg[0]=0x22 received from mcu (Power Monitoring Failure as the Wake Up Source)

 Transfer to SDRAM Successful

BmeHw: Downloading BME 1 software .....!

BmeHw: Bme 1 software code downloaded successfully

The feature bit has been successfully modified for  eth0 eth1 PERI VDSL APs...

******sysutil apfeature all vlanbridge enable******

 alm freq 20
 status freq 30
/tmp/dslSavedConfig.conf file not found

configuration file /etc/vdsl.conf:start______

configuration file /etc/vdsl.conf:start0______

OamOptionMask Set to 3
_____________________BEI:fpvdslconfigfile == NULL__________________
 taskUi: profileNum = 2 Sizeof ipos_port_profile=144

Please execute 'vdsl' in 15 seconds to enter into Supervisor mode
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0

Changing port profile #2 BAND_PLAN=0x1 PTM MODE=0x0
OamoptionMask 3
optionMask 8ath_tx_reset Started tx reset
ath_tx_reset Completed tx reset
ath_bstuck_tasklet: stuck beacon; resetting (bmiss count 36)
ar9287EepromSetPowerPerRateTable: Reg power: 20 dBm Net ant gain allowed: 0 dB
ar9287EepromSetPowerPerRateTable: Power Limit (Reg power - Net ant gain): 19 dBm
ar9287EepromSetPowerPerRateTable: Number of chains: 2 Per chain power limit: 16 dBm
ar9287EepromSetPowerPerRateTable: Target powers: 1Mb/s: 15 dBm 11Mb/s: 15 dBm 6Mb/s: 15 dBm 54Mb/s: 12 dBm 
MCS0(HT20): 15 dBm MCS7(HT20): 10 dBm MCS0(HT40): 0 dBm MCS7(HT40): 0 dBm
ar9287EepromSetPowerPerRateTable: syn 2457 ctl 2457 ext 2457 is40 0
ar9287EepromSetPowerPerRateTable: Ctl mode: 1 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Ctl mode: 2 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Ctl mode: 5 Per chain minimum CTL power: 15 dBm
ar9287EepromSetPowerPerRateTable: Chosen powers:1Mb/s: 15 dBm 11Mb/s: 15 dBm 6Mb/s: 15 dBm 54Mb/s: 12 dBm 
MCS0(HT20): 15 dBm MCS7(HT20): 10 dBm MCS0(HT40): 0 dBm MCS7(HT40): 0 dBm
2xMaxPowerLevel: 37 (LEG)

JXU: set the rxBufsize to 3851