Netgear WG602v3

From TechInfoDepot
Jump to navigationJump to search
multiple revisions of this device, use caution
bg (G54)
54 Mbps Wireless Access Point
Netgear WG602 v3.0 front.jpg
Support
Wikipedia
InfoDepot Wiki
3rd Party Firmware
dd-wrt
OpenWrt
Incompatible
Tomato any flavor
Incompatible
Gargoyle
Incompatible
Platform
BrandModelRev
Netgear WG602 v3
FCC ID
IC ID
Type
access point
CPU1
CPU1 Type
MIPS3300
CPU1 Speed
200 MHz
Flash1 Chip
Intel 28F160C3
Flash1 Size
2 MiB2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br />
RAM1 Size
8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br />
RAM1 Chip
EtronTech EM638425TS-6
ETH chip1
Ethernet Port Count
1-100MbE-LAN
Wired Standard
IEEE 802.3/3u

802dot11 OUI: none specified

Expansion IF types
none specified
Power
7.5 VDC, 1 A
Connector type
barrel
Other

Default SSID: NETGEAR (43 addl. devices)
Default IP address: 192.168.0.227
the IP 192.168.0.227 is used by 3 additional devices
of which 3 are Netgear devices
Default login user: admin
Default login password: password
admin:password credentials used by 420 additional devices
of which 301 are Netgear devices

Manuf/OEM/ODM
3rd Party Firmware Support
DD-WRT • (List)
Retail
FCC approval date 09 September 2004
Radio 1
Chip1
Chip2
Broadcom BCM2050
Wireless interface OUI
none specified
Antenna Connector Type
RP-SMA
Wireless Standard
IEEE 802.11b/g
802.11g
up to 54 Mbps
802.11b
up to 11 Mbps
WiFi Operating Frequency
2.4 GHz
Radio cor_rev
7
 CPU1 brandRadio1 chip1 brandRadio1 chip2 brand
Netgear WG602v1IDTIntersilIntersil
Netgear WG602v2IntersilIntersilIntersil
Netgear WG602v3BroadcomBroadcomBroadcom
Netgear WG602v4BroadcomBroadcom

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.

For a list of all currently documented Netgear device with specifications, see Netgear.

54 Mbps - 2.4GHz 802.11g = G54 class

Overview

"297632301" is silkscreened on the board in the FCC photos.

Links of Interest

On the DD-WRT wiki
On the DD-WRT supported devices table
On the OpenWrt wiki


Flashing

Flashing dd-wrt

Supported by dd-wrt as of = v24 RC-5 (11/05/07) micro - build 8332

initial flash: use Tftp flash

Someone who has this router should write a proper wiki entry on how to upgrade, but until that is done, here is a link to some basic information

http://www.dd-wrt.com/phpBB2/viewtopic.php?p=475282



dd-wrt Firmware Replacement on Netgear WG602v3 Wireless Access Point
Augur 11:34, 30 August 2010 (CEST)

Read This First

READ the Peacock Thread first. use the wiki and forums to do research before even contemplating installing dd-wrt
check the WG602v3 works before flashing
check your WG602v3 matches the details in the [Supported Devices page]

Firmware

the WG602v3 only has 2mb flash memory so can only support the micro builds
BrainSlayer builds (13525) dd-wrt.v24_micro_generic.bin
ftp://dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/older/12-28-09-r13525/broadcom/
[dd-wrt.v24_micro_generic.bin]
using [tftp2.exe]

Preparing The WG602v3

  1. connect the WG602v3 to a computer using a network cable
  2. set static ip of computer to 192.168.0.220/24
    • there should be no means of access to any other router or dhcp server or the WG602v3 will not set its default ip address.
  3. perform a [30-30-30 Hard Reset]
  4. in browser go to http://192.168.0.227 L:admin P:password and check it is the default netgear setup


Installing dd-wrt

  1. on the computer disable firewall and antivirus
  2. run tftp2.exe
    • configure as follows
    • Server to 192.168.0.227
    • password leave blank
    • pick the firmware
    • set rety to 50
  3. open a command prompt and type in ping 192.168.0.227 -t
  4. unplug power lead from router
  5. replug power lead into router
  6. the instant you get a ping response from the router click Upgrade
    • if it doesn't work try unplugging again (timing matters)
    • stop pinging the router (ctrl-c)


  • (very important) wait 5-7 minutes after you get the success message before doing anything. recomend you walk away and get a drink


After Install. Initial Preparation Before Use

  1. reconfigure the static ip of the computer to 192.168.1.220/24
  2. in browser go to http://192.168.1.1
    • if you get the dd-wrt web gui password change page perform a power cycle on the router
  3. when the web gui comes up again perform a 30-30-30 hard reset
  4. wait for gui to come up again
    • change default username and password
    • close browser
  5. open browser and load the gui again. you should now have the status screen
    • login and configure
  6. remember to re-enable firewall, antivirus, and dhcp on the computer

JTAG-Serial Info

Serial

Serial Pinouts

Pinout for the UART1 connector

Looking from the backside of the device the pinout of UART1 (J5) is

   *      Pin 1 = 3,3V
   *      Pin 2 = RxD
   *      Pin 3 = TxD
   *      Pin 4 = Gnd

Pictures

Retail Images