Linksys WRT54GS v1.1

From TechInfoDepot
Jump to navigationJump to search
multiple revisions of this device, use caution
bg (G54)
Wireless-G Broadband Router with SpeedBooster
Linksys WRT54GS.jpg
Support
Wikipedia
InfoDepot Wiki
WikiDevi.wi-cat.ru
3rd Party Firmware
dd-wrt
OpenWrt
Tomato any flavor
Gargoyle
Status Unknown
Platform
BrandModelRev
Linksys WRT54GS v1.1
Serial number prefix
CGN2
FCC ID
IC ID
Type
wireless router
Series
WRT54GS
CPU1
CPU1 Type
MIPS BMIPS3300 (R1)
CPU1 Speed
200 MHz
Flash1 Chip
Intel TE28F640J3C-120
Flash1 Size
8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br />
RAM1 Size
32 MiB33,554,432 B <br />262,144 Kib <br />32,768 KiB <br />256 Mib <br />0.0313 GiB <br />
RAM1 Chip
SK hynix HY5DU561622DT-J
nvram Size
32K
ETH chip1
Switch
Broadcom BCM5325E
Ethernet Port Count
1-100MbE-WAN
4-100MbE-LAN
Wired Standard
IEEE 802.3/3u
Port-based vlan
Yes - Via GUI & nvram

802dot11 OUI: 00:13:10 (16 E, 17 W)
Ethernet OUI: 00:13:10 (16 E, 17 W)

Stock bootloader
CFE
Stock FW OS
Linux 2.4
Expansion IF types
none specified
Power
12 VDC, 1 A
Connector type
barrel
Serial Port (UART)
yes, 10-pin header, unpopulated, , (115200 8N1)
JTAG Port
yes, 12-pin header, unpopulated
Other

Default SSID: Linksys (4 addl. devices)
Default IP address: 192.168.1.1
the IP 192.168.1.1 is used by 1304 additional devices
of which 153 are Linksys devices
Default login user: blank
Default login password: admin
blank:admin credentials used by 267 additional devices
of which 134 are Linksys devices

Default Channel(s)
6
Manuf/OEM/ODM
3rd Party Firmware Support
Broadband-Hamnet
, DD-WRT • (List)
, OpenWrt • (List | Dev | DLs)
, Tomato • (List | DLs)
, TomatoUSB • (List | DLs)
Retail
FCC approval date 17 September 2004
Country of manuf China
Physical
Dimensions
7.32" x 1.89" x 6.06"
Radio 1
Chip1
Chip2
Broadcom BCM2050
Wireless interface OUI
00:13:10
Antenna Connector Type
RP-TNC
Wireless Standard
IEEE 802.11b/g
802.11g
up to 54 Mbps
802.11b
up to 11 Mbps
WiFi Operating Frequency
2.4 GHz
Radio cor_rev
7
Radio Capabilities
ap sta wet led wme 802.11d 802.11h rm cqa afterburner acktiming
 FCC ID
Linksys WRT54G v2.2Q87-WT54GV22
Linksys WRT54G v3.0Q87-WT54GV22
Linksys WRT54G v3.1Q87-WT54GV22
Linksys WRT54GS v2.0Q87-WT54GV22
Linksys WRT54GS v2.1Q87-WT54GV22
 CPU1 brandRadio1 chip1 brandRadio1 chip2 brand
Linksys WRT54GS v1.0BroadcomBroadcomBroadcom
Linksys WRT54GS v1.1BroadcomBroadcomBroadcom
Linksys WRT54GS v2.0BroadcomBroadcomBroadcom
Linksys WRT54GS v2.1BroadcomBroadcomBroadcom
Linksys WRT54GS v3BroadcomBroadcomBroadcom
Linksys WRT54GS v4BroadcomBroadcomBroadcom
Linksys WRT54GS v5.0BroadcomBroadcomBroadcom
Linksys WRT54GS v5.1BroadcomBroadcomBroadcom
Linksys WRT54GS v6.0BroadcomBroadcomBroadcom
Linksys WRT54GS v7.0BroadcomBroadcom
Linksys WRT54GS v7.2BroadcomBroadcom

For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.

For a list of all currently documented Linksys device with specifications, see Linksys.

54 Mbps - 2.4GHz 802.11g = G54 class


Overview

Links of Interest

Flashing

Flashing DD-WRT

 

Supported by dd-wrt as of = ?

NEWD or VINT

WRT54GS v1.1 uses the Broadcom BCM4712 chip rev 1 but since the "wl0_corerev" is 7 (see NEWD or VINT for more info) WRT54GS v1.1 users should use standard NEWD builds

How to Flash

Make sure to get all the files you need first. Start with dd-wrt.v24_mini_generic.bin

  1. Perform a Hard reset or 30/30/30
  2. Upload dd-wrt through the firmware update page
  3. WAIT for at least five minutes before you continue! (longer is better) Give the router plenty of time to to boot.
  4. Perform a Hard reset or 30/30/30
  5. WAIT for at least five minutes before you continue! (longer is better) Give the router plenty of time to to boot.
  6. Power Cycle
  7. Open your browser to http://192.168.1.1. Configure to your liking. Enjoy.
  8. Check for recommended builds here.

Flashing OpenWrt

On the OpenWrt ToH (techdata entry)
On the OpenWrt Wiki
Support started version: 0.9
Current supported version: 22.03.5

Please insert instructions here

Flashing Tomato

Please insert instructions here

Flashing Gargoyle

Supported

Please insert instructions here

Upgrading

Updating DD-WRT

If dd-wrt is already on the router follow these instructions. If stock firmware is on the router follow the flashing instructions.

  1. Check for recommended builds here first.
  2. Set your computer to a static IP of 192.168.1.7. (or to whatever subnet the router is on) Disable all firewalls and security. Disable wireless on your computer and only have the router connected to the flashing computer by the ethernet cable between the two.
  3. Hard reset or 30/30/30 (If the router supports it, if not, reset to defults in the GUI) prior to flashing. Wait. Check for password page on re-login and change password.
  4. Flash firmware. You can use the webgui except if you have a belkin router. (For belkin use tftp.exe to flash)
  5. Wait...at least three minutes. Lights should return to normal. See important2, below. Failing to wait is how most people brick their routers.
  6. Do a power cycle of the router. (Unplug the cord, count to 30 and plug it back in.)
  7. Wait for the lights to return to normal usually about 2 minutes.
  8. Hard reset or 30/30/30 again (If the router supports it, if not, reset to defults in the GUI). Wait. Check for the password page and re-login to change the password. Then you can reconfigure your settings manually.
  9. Once configured set your computer back to autoIP and autoDNS.

Important1: This Hard reset or 30/30/30 works fine for Asus router, but you do have to power cycle after the reset.

Important2: After you flash the firmware, and before you do the hard reset, the router will be building some nvram settings. YOU MUST WAIT FOR THIS TO FINISH PRIOR TO DOING ANYTHING WITH THE ROUTER INCLUDING A HARD RESET. Usually, you can tell when this process is completed by the WAN light coming on, but it does take several minutes. Go have a beer. There are starting to be more and more people who BRICK their routers by not waiting until the nvram is rebuilt, PRIOR to doing a hard reset. YOU NEED TO WAIT!

Reverting

Reverting to OEM Firmware from DD-WRT

  1. Read the peacock announcement found here: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
  2. Do a Hard reset or 30/30/30 on the router according to note 1 of the peacock announcement (30/30/30)
  3. Set a static IP on your computer to 192.168.1.7. Subnet mask should be 255.255.255.0.
  4. Connect the lan cable from your computer to a LAN port of your router. Make sure your router is plugged in. Nothing should be connected to your computer or the router except the LAN cable between them. Turn your firewall and any wireless computer connections OFF.
  5. Power cycle the router (unplug the power from the router for 30 seconds and then plug it back in)
  6. Open your browser to 192.168.1.1 by putting that in the browser address window of your browser. You should open the linksys webgui and NOT a page that says Management Mode. If you see management mode, power cycle the router again.
  7. Enter your username and password
  8. Go to administration and firmware upgrade
  9. Navigate to the folder that you are using, and select WRT54GSv3_4.71.4.001_fw.bin once you've unzipped it.
  10. Hit upgrade
  11. When you get a success, wait FIVE FULL minutes.
  12. When you can again access the Linksys webgui using a browser at 192.168.1.1, do another Hard reset or 30/30/30 on the router.
  13. Reset your computer Ethernet connection to auto IP and auto DNS

JTAG-Serial Info

JTAG

JTAG Pinouts

 nTRST  1o o2  GND
   TDI  3o o4  GND
   TDO  5o o6  GND
   TMS  7o o8  GND
   TCK  9o o10 GND
 nSRST 11o o12 N/C

Using Universal JTAG Adapter

  white  1o o2	black
    red  3o o4	GND
   blue  5o o6	GND
  green  7o o8	GND
 yellow  9o o10 GND
 orange 11o o12 N/C
  • /noemw switch required for flash

DD-WRT JTAG Recovery

JTAG:

  1. Backup CFE x2 (Compare the files, they must match exactly or there is something wrong with your JTAG setup)
  2. Erase Wholeflash x2
  3. Flash CFE
  4. Unplug Power
  5. Unplug JTAG Cable

TFTP:

  1. Set Rig ip static 192.168.1.10
  2. Plug network cable from rig to port 1
  3. Get TFTP ready, server ip - 192.168.1.1, Password - blank, file - dd-wrt.v24_mini_generic.bin
  4. Plug in power
  5. Wait for DMZ light to do a steady pulse, When it is lit on the 3rd time click upgrade. The DMZ light must be lit when you click upgrade.
  6. Hard Reset 30\30\30

Serial

Serial Pinouts

 VCC 1 o o 2  VCC
 TX1 3 o o 4  TX0
 RX1 5 o o 6  RX0
 N/C 7 o o 8  N/C
 GND 9 o o 10 GND

vlan Info

DD-WRT vlan Info

http://www.dd-wrt.com/phpBB2/viewtopic.php?p=479598#479598

TechInfoDepot:DD-WRT/VLAN Support

Confirmed the WRT54GS v1.1 supports port-based vlans via the GUI & nvram.

WRT54G v1.1's ports are mapped like this:

 4 3 2 1 | case labels
 3 2 1 0 | nvram port numbers

Defaults

root@DD-WRT:~# nvram show | grep vlan.ports
vlan0ports=3 2 1 0 5*
vlan1ports=4 5
size: 19244 bytes (13524 left)
root@DD-WRT:~# nvram show | grep port.vlans
port5vlans=0 1 16
port3vlans=0
port1vlans=0
size: 19244 bytes (13524 left)
port4vlans=0
port2vlans=0
port0vlans=1
root@DD-WRT:~# nvram show | grep vlan.hwname
vlan1hwname=et0
size: 19244 bytes (13524 left)
vlan0hwname=et0
root@DD-WRT:~# lsmod
Module                  Size  Used by
ip_nat_pptp             2560   0 (unused)
ip_conntrack_pptp       3036   1
ip_nat_proto_gre        1664   0 (unused)
ip_conntrack_proto_gre    2584   0 [ip_nat_pptp ip_conntrack_pptp]
etherip                 5104   0 (unused)
switch-robo             5356   0 (unused)
switch-core             6352   0 [switch-robo]
root@DD-WRT:~# ls /proc/switch
eth0
root@DD-WRT:~# cat /proc/switch/eth0/vlan/0/ports
0       1       2       3       5t*
root@DD-WRT:~# cat /proc/switch/eth0/vlan/1/ports
4       5t
root@DD-WRT:~# cat /proc/switch/eth0/vlan/2/ports
4
root@DD-WRT:~#

commands

root@DD-WRT:~# nvram set vlan0ports="2 1 0 5*"
root@DD-WRT:~# nvram set vlan1ports="3 4 5"
root@DD-WRT:~# nvram commit
root@DD-WRT:~# reboot

nvram

root@DD-WRT:~# nvram show | grep vlan.ports
vlan0ports=2 1 0 5*
vlan1ports=3 4 5
size: 19365 bytes (13403 left)
root@DD-WRT:~# nvram show | grep port.vlans
port5vlans=0 1 16
port3vlans=0
port1vlans=0
size: 19365 bytes (13403 left)
port4vlans=0
port2vlans=0
port0vlans=1
root@DD-WRT:~# nvram show | grep vlan.hwname
vlan1hwname=et0
size: 19365 bytes (13403 left)
vlan0hwname=et0
root@DD-WRT:~#

GUI

root@DD-WRT:~# nvram show | grep vlan.ports
vlan0ports=3 2 1 0 5*
vlan1ports=4 5
size: 19348 bytes (13420 left)
root@DD-WRT:~# nvram show | grep port.vlans
port5vlans=0 1 16
port4vlans=1 18 19
port3vlans=0 18 19
port2vlans=0 18 19
port1vlans=0 18 19
port0vlans=1 18 19
size: 19348 bytes (13420 left)
root@DD-WRT:~# nvram show | grep vlan.hwname
vlan1hwname=et0
size: 19348 bytes (13420 left)
vlan0hwname=et0
root@DD-WRT:~#

Pictures

DarkShadow's Unit
FCCID Q87-WT54GV22

Notes

DD-WRT Notes

[comment added 4/25/08 by WellingtonFelix] I installed the new version "dd-wrt.v24_mega_generic.bin" over default configuration of the version "dd-wrt.v23_vpn_generic.bin" and I had no problems.

[comment added 5/7/08 by Sapremias] Flashed dd-wrt.v24_mega_generic.bin directly from linksys web interface (version WRT54GSv3_4.71.4.001_fw.bin) without issue. -Sapremias

[comment added 10/5/08 by richwillal] I installed dd-wrt v24 sp1 Mega Vintage (dd-wrt.v24-9517_VINT_mega) from stock firmware with no issues. Standard process: 1) Reset router - reset for 30 secs w/ power on 2) Upload dd-wrt 3) Reset router - reset for 30 secs w/ power on 4) Disconnect/reconnect or ipconfig /renew

[comment added 04/02/09 by tribble222] I nearly bricked my router going directly from Linksys firmware to dd-wrt.v24-11296_VINT_STD.bin. Pinged on boot but tftp wouldn't work. Router didn't even respond to JTAG. Shorting pins 5&6 with the router unplugged somehow fixed everything. From there I was able to flash to mini, then back to std.