Linksys WRT160N v2

From TechInfoDepot
Jump to navigationJump to search
multiple revisions of this device, use caution
bgn (N300)
Ultra RangePlus Wireless-N Broadband Router
Linksys WRT160N 01.jpg
Support
Wikipedia
InfoDepot Wiki
WikiDevi.wi-cat.ru
3rd Party Firmware
dd-wrt
OpenWrt
Tomato any flavor
Incompatible
Gargoyle
Status Unknown
Platform
BrandModelRev
Linksys WRT160N v2
FCC ID
IC ID
Type
wireless router
CPU1
Ralink RT2880
CPU1 Type
MIPS 4KEc
CPU1 Speed
266 MHz
Flash1 Chip
Eon EN29LV320AB-70TCP
Flash1 Size
4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br />
RAM1 Size
16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br />
RAM1 Chip
PSC A2V64S40CTP-G6 x 2
ETH chip1
Ralink RT2880
Switch
Realtek RTL8306SD
Ethernet Port Count
1-WAN
4-100MbE-LAN
Wired Standard
IEEE 802.3i/3u

802dot11 OUI: 00:21:29 (9 E, 16 W), 00:22:6B (8 E, 11 W), 00:23:69 (12 E, 19 W)
Ethernet OUI: 00:21:29 (9 E, 16 W), 00:22:6B (8 E, 11 W), 00:23:69 (12 E, 19 W)

Expansion IF types
none specified
Power
12 VDC, 1 A
Connector type
barrel
Serial Port (UART)
yes, 5-pin header, internal, J10, (115200 8N1)
JTAG Port
yes, looks like it, J11

Additional chips
2.4GHz Power Amplifier IC;Richwave;RTC6694;;2;SiGe;QFN24;

Other

Default IP address: 192.168.1.1
the IP 192.168.1.1 is used by 1311 additional devices
of which 153 are Linksys devices
Default login user: blank
Default login password: admin
blank:admin credentials used by 267 additional devices
of which 134 are Linksys devices

Manuf/OEM/ODM
3rd Party Firmware Support
Retail
FCC approval date 15 May 2008
ASIN B000Z3U1P6 Flag of the United States.svg
Country of manuf China
Radio 1
Chip1
Ralink RT2880
Chip2
Ralink RT2820
Wireless interface OUI
00:21:29, 00:22:6B, 00:23:69
Antenna Connector Type
none specified
MIMO status
2x2:2
Wireless Standard
IEEE 802.11b/g/n
802.11n
up to 300 Mbps
802.11g
up to 54 Mbps
802.11b
up to 11 Mbps
WiFi Operating Frequency
2.4 GHz
 CPU1 brandRadio1 chip1 brandRadio1 chip2 brand
Linksys WRT160N v1.0BroadcomBroadcomBroadcom
Linksys WRT160N v1.1BroadcomBroadcomBroadcom
Linksys WRT160N v2RalinkRalinkRalink
Linksys WRT160N v3BroadcomBroadcom

For a list of all currently documented Ralink chipsets with specifications, see Ralink.
For a list of all currently documented Realtek chipsets with specifications, see Realtek.

For a list of all currently documented Linksys device with specifications, see Linksys.

300 Mbps - 2SS 2.4GHz 802.11n (40MHz chan.) = N300 class

Overview

"3763-01001201R" is silkscreened on the board in the FCC photos.

WRT160N v2 serial numbers appear to start with CSE1.

Links of Interest

Firmware projects

Wikis

Forum threads

(Note: DD-WRT doesn't currently support the WRT160Nv2)

Flashing

Flashing dd-wrt

Flashing OpenWrt

On the github
Support started version: ?
Current supported version: ?
Comment:
OpenWrt (leitec)

Please insert instructions here

JTAG-Serial Info

Serial

Serial Pinouts

WAN Port    
        (   )
        (RxD)
        (TxD)
        (   )
        (GND)
         J10

Boot log

boot log
U-Boot 1.1.3 (Jul 26 2008 - 17:24:31)

Board: RT2880 DRAM:  16 MB
******************************
Switch Reset Occurred
******************************
The Flash ID =22F9 MAN_ID=7F
CFI QUERY flash sectors=[8],sector_size=[2000]
CFI QUERY flash sectors=[63],sector_size=[10000]
============================================
ASIC -VerB/C (MAC to 100PHY Mode)
DRAM COMPONENT=64Mbits
DRAM BUS=32BIT
Total memory = 16Mbytes
Date:Jul 26 2008  Time:17:24:31
============================================

--------***** Rtl8306_asicSoftReset *****-------

 --------***** Get the RTL8306SD Manufactory ID=5988 *****-------
Found valid NVRAM.
Board IP Address                192.168.1.1
Default host ip Address         192.168.1.10
Board MAC Address               00:22:6b:78:29:ee
Boot file name                  "uboot.bin"
Boot address                    BFC40000
Deafult baud rate               115200

*** Press Ctrl-C or ESC key to stop boot run ***                                                                                         0 
3: System Boot system code via Flash.
## Booting image at bf040000 ...
   Image Name:   Linux Kernel Image
   Created:      2009-08-21   3:23:49 UTC
System Control Status = 0x02110084
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3416064 Bytes =  3.3 MB
   Load Address: 8a000000
   Entry Point:  881d6040
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 881d6040) ...
## Giving linux memsize in MB, 16

Starting kernel ...


THIS IS ASIC
ramsize = 16 MBytes
rambase not set, set to default (0x08000000)
MEMORY DESCRIPTOR dump:
[0,88259e40]: base<08000000> size<01000000> type<Free RAM memory>

 The CPU feqenuce set to 266 MHz
CPU revision is: 0001906c
icache: sets:256, ways:4, linesz:16 ,total:16384, waybit:12, flags:0x0
dcache: sets:256, ways:4, linesz:16 ,total:16384, waybit:12, flags:0x0
i waysize = 4 GiB, d waysize = 4 GiB, i sets= 256, d sets=256
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, linesize 16 bytes.
[setup_scache]:1032
Linux version 2.4.30 (tcy@cybertan) (gcc version 3.3.6) #9 Fri Aug 21 11:23:36 CST 2009
Determined physical RAM map:
 memory: 01000000 @ 08000000 (usable)
On node 0 totalpages: 36864
zone(0): 36864 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock2 noinitrd
cause = f080837c, status = 1000c700
calculating r4koff... 00144b50(1330000)
CPU frequency 133.00 MHz
Using 133.000 MHz high precision timer.
Calibrating delay loop... 265.42 BogoMIPS
Memory: 12376k/16384k available (1870k kernel code, 4008k reserved, 112k data, 100k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
pci.c pcibios_init():840
BAR0 at slot 0 = ffffffff
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
bootnv start=0xbf03ea00, end=0xbf03fe00
Ralink gpio driver initialized
spidrv_major = 217
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x300500 (irq = 9) is a 16550A
ttyS01 at 0x300c00 (irq = 8) is a 16550A
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
RA2880 Ethernet Driver Initilization. v1.01  256 rx/tx descriptors allocated!
Netlink init ok!
PROC INIT OK!

--------***** Rtl8306_asicSoftReset *****-------
--------***** Get the RTL8306SD Manufactory ID=5988 *****-------
rdm_major = 254
PPP generic driver version 2.4.2
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
FLASH_API: MAN_ID=7F DEV_ID=22F9 SIZE=4MB
physmap flash device: 400000 at bc400000
cfi_cmdset_0002():
    cfi->cmdset=0
    cfi->interleave=1
    cfi->device_type=2
    cfi->cfi_mode=1
    cfi->addr_unlock1=0
    cfi->addr_unlock2=0
    cfi->fast_prog=1
    cfi->mfr=0
    cfi->id=0
    cfi->numchips=1
    cfi->chipshift=22
    cfi->cfiq->P_ADR=40
    cfi->cfiq->NumEraseRegions=2
Pirmary Extended Table:
    major='1'
    minor='1'
    Address Sensitive Unlock=0
    Erase Subspend=2
    Block Protect=4
    Block Temp Unprotect=1
    Block [Un]Protect Scheme=4
    Simultaneous Operation=0
    Burst Mode=0
    Page Mode=0
    ACC Min=165
    ACC Max=181
    TopBottom=2
 Amd/Fujitsu Extended Query Table v1.1 at 0x0040
cfi_cmdset_0002(): bootloc=2
cfi_cmdset_0002(): Region=0 BlockSize 0x2000 bytes, 8 blocks
cfi_cmdset_0002(): Region=1 BlockSize 0x10000 bytes, 63 blocks
cfi_cmdset_0002(): cfi->chips[0].word_write_time=16
cfi_cmdset_0002(): cfi->chips[0].buffer_write_time=1
cfi_cmdset_0002(): cfi->chips[0].erase_time=1024
number of CFI chips: 1
Region0: SectorSize=0x2000 SectorNum=8
Region1: SectorSize=0x10000 SectorNum=63
cfi_cmdset_0002: Using word write method.
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Using physmap partition definition
Creating 4 MTD partitions on "RT2880 SOC Physically mapped flash":
0x00000000-0x00040000 : "Bootloader"
mtd: Giving out device 0 to Bootloader
0x00040000-0x003f0000 : "Kernel"
mtd: Giving out device 1 to Kernel
0x000e2464-0x003f0000 : "Rootfs"
mtd: partition "Rootfs" doesn't start on an erase block boundary -- force read-only
mtd: Giving out device 2 to Rootfs
0x003f0000-0x78633858 : "nvram"
mtd: partition "nvram" extends beyond the end of device "RT2880 SOC Physically mapped flash" -- size truncated to 0x10000
mtd: Giving out device 3 to nvram
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (1152 buckets, 9216 max) - 368 bytes per conntrack
Register conntrack protocol helper for ESP...
init IP_nat_proto_esp register.
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
ip_tables: (C) 2000-2002 Netfilter core team
ipt_random match loaded
ipt_time loading
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 100k freed
console started
trying to start /sbin/init
MTD_open
MTD_read
MTD_close
Needed modules: rt2860v2_ap
cmd=[insmod rt2860v2_ap ]
The chipset is RA_RT2880

Hit enter to continue...
Bootloader is UBOOT.

CODE_PATTERN =>N160
Make date==>Year:9,Month:8,Day:20
Firmware version =>v2.0.03
MD5=[e8235438ca0893272b95da2368931c57]
killall: httpd: no process killed
Console log level set to 1
cmd=[vconfig set_name_type VLAN_PLUS_VID_NO_PAD ]
start_vlan():set eth2 hwaddr to 00:22:6b:78:29:ee
cmd=[vconfig add eth2 1 ]
ioctl: Device or resource busy
cmd=[vconfig add eth2 2 ]
cmd=[brctl addbr br0 ]
cmd=[brctl setfd br0 0 ]
name=[vlan1] lan_ifname=[br0]
start_lan():set vlan1 hwaddr to 00:22:6b:78:29:ee
cmd=[brctl addif br0 vlan1 ]
name=[ra0] lan_ifname=[br0]
cmd=[brctl addif br0 ra0 ]
lo: File exists
Set 66560 to /proc/sys/net/core/rmem_max ...
cmd=[resetbutton ]
start syslogd...
br0 192.168.1.100  86400
cmd=[udhcpd /tmp/udhcpd.conf ]
info, udhcp server (v0.9.8) started
cmd=[tftpd -s /tmp -c -l -P N160 ]
tftp server started
tftpd: standalone socket
[HTTPD Starting on /www]
cmd=[httpd ]
zebra disabled.
upnpd adding route[route add -net 239.0.0.0 netmask 255.0.0.0 br0]

J>>>>>> START WSC  >>>>>>>>>>>
Name to be unset = wsc_config_method=pin

led reset.....LED1 orange, LED2 Green
iwpriv cmd is iwpriv ra0 set WscConfMode=7
iwpriv cmd is iwpriv ra0 set WscConfStatus=1
cmd=[udhcpc -i vlan2 -l br0 -p /var/run/wan_udhcpc.pid -s /tmp/udhcpc ]
info, udhcp client (v0.9.8) started

Hit enter to continue...
HNAP:using uuid:00220022-6b78-29ef-efee-00226b7829ef
               libupnp: using UDP SSDP_PORT = 1900

Hit enter to continue...

Info

cat /proc/mtd

# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00040000 00010000 "Bootloader"
mtd1: 003b0000 00010000 "Kernel"
mtd2: 0030db9c 00010000 "Rootfs"
mtd3: 00010000 00010000 "nvram"

cat /proc/cpuinfo

# cat /proc/cpuinfo
system type             : Palmchip Surfboard
processor               : 0
cpu model               : unknown V6.12
BogoMIPS                : 265.42
wait instruction        : no
microsecond timers      : yes
tlb_entries             : 16
extra interrupt vector  : yes
hardware watchpoint     : no
VCED exceptions         : not available
VCEI exceptions         : not available

lsmod

# lsmod
Module                  Size  Used by
rt2860v2_ap           777824   1

ps

# ps
  PID  Uid        VSZ Stat Command
    1 root       1808 S   /sbin/init noinitrd
    2 root            SW  [keventd]
    3 root            SWN [ksoftirqd_CPU0]
    4 root            SW  [kswapd]
    5 root            SW  [bdflush]
    6 root            SW  [kupdated]
    7 root            SW  [mtdblockd]
    9 root            SW  [rtmpWscHandle]
   22 root       1764 S   resetbutton
   25 root       1192 S   syslogd -O /dev/null
   30 root       1768 S   tftpd -s /tmp -c -l -P N160
   32 root       1476 S   udhcpd /tmp/udhcpd.conf
   33 root       1200 S   crond -c /etc/cron.d
   36 root       5472 S   httpd
   40 root       1928 S   upnpd br0
   46 root       2364 S   wscd -m 1 -a 192.168.1.1
   61 root       1452 S   udhcpc -i vlan2 -l br0 -p /var/run/wan_udhcpc.pid -s
   63 root       2364 S   wscd -m 1 -a 192.168.1.1
   64 root       2364 S   wscd -m 1 -a 192.168.1.1
   65 root       2364 S   wscd -m 1 -a 192.168.1.1
   66 root       2364 S   wscd -m 1 -a 192.168.1.1
   68 root       2364 S   wscd -m 1 -a 192.168.1.1
   69 root       2364 S   wscd -m 1 -a 192.168.1.1
   70 root       2364 S   wscd -m 1 -a 192.168.1.1
   72 root       2364 S   wscd -m 1 -a 192.168.1.1
   73 root       2364 S   wscd -m 1 -a 192.168.1.1
   82 root       1296 S   /bin/sh
   94 root       1192 R   ps

cat /proc/meminfo

# cat /proc/meminfo
        total:    used:    free:  shared: buffers:  cached:
Mem:  12775424 10489856  2285568        0  1245184  2834432
Swap:        0        0        0
MemTotal:        12476 kB
MemFree:          2232 kB
MemShared:           0 kB
Buffers:          1216 kB
Cached:           2768 kB
SwapCached:          0 kB
Active:           1696 kB
Inactive:         2300 kB
HighTotal:           0 kB
HighFree:            0 kB
LowTotal:        12476 kB
LowFree:          2232 kB
SwapTotal:           0 kB
SwapFree:            0 kB

Pictures

mode="slideshow"

User Images