Serial info

From TechInfoDepot
Jump to navigationJump to search

Info dervied from[edit]

boot log
U-Boot 1.1.4 (Jun 19 2008 - 14:02:55)

U-Boot code: 00000000 -> 0001C1F0  BSS: -> 00021498
CPU Clock: 200 MHz
1.8V Vdd Output: 1.793
2.5V Vdd Output: 2.531
___ PCI Device List Start ____
bus:00 device:01 function:00
    vendor:1a30 device_id:0680 class:0d80 interrupt:06
____ PCI Device List End ____
RAM Configuration:
Bank #0: 00000000 32 MB
Flash Manufacturer: EON
Flash Device: ENLV320B(4MB)
Flash:  4 MB
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0
Verifying image integrity.
Good checksum
## Starting application at 0x10040000 ...
Uncompressing Linux ... done, booting the kernel.
Linux version 2.6.16-star (jacky.yang@RH001.u-media.com)
(gcc version 3.4.6) #1 Mon Jun 22 18:20:51 CST 2009
CPU: FA526id(wb) [66015261] revision 1 (ARMv4)
Machine: STAR STR9100
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 2, 16 byte lines, 512 sets
CPU0: D cache: 16384 bytes, associativity 2, 16 byte lines, 512 sets
CPU clock at 200MHz
AHB clock at 100MHz
APB clock at 50MHz
D-scratchpad of size 8192 at f7800000
Built 1 zonelists
Kernel command line: root=/dev/ram0
PID hash table entries: 256 (order: 8, 4096 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB = 32MB total
Memory: 28356KB available (1736K code, 195K data, 88K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (<NULL>); looks like an initrd
Freeing initrd memory: 2011K
NET: Registered protocol family 16
PCI clock at 33M
PCI: bus0: Fast back to back transfers disabled
PCI Bridge found
PCI map irq: 00:00.00 slot 0, pin 1, irq: 0
PCI map irq: 00:01.00 slot 1, pin 1, irq: 5
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
io scheduler noop registered
io scheduler deadline registered (default)
GPIO interrupt handler install ok.
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x78000000 (irq = 10) is a 16550A
RAMDISK driver initialized: 4 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
VLAN0_VLAN_TAG: 0
init RTL8201CP
STR9100 NOR Flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
config_offset=0x3f0000
Creating 4 MTD partitions on "STR9100 NOR Flash":
0x00000000-0x00020000 : "ARMBOOT"
0x00040000-0x003f0000 : "Linux Kernel"
0x00020000-0x00030000 : "Non-volatile Config Partition"
0x003f0000-0x00800000 : "Config Partition"
mtd: partition "Config Partition" extends beyond the end of device "STR9100 NOR Flash" -- size truncated to 0x10000
GACT probability on
Mirror/redirect action on
Simple TC action Loaded
u32 classifier
    Actions configured
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
RAMDISK: lzma compressed image found at block 0
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 88K
init started: BusyBox v1.8.1 (2009-06-22 18:22:59 CST)
starting pid 610, tty '/dev/ttyS0': '/bin/sh'
U-Media, mount_config.sh: Who call me?
 (610) Got config lock
 (610) Mounting configuration filesystem
0
0
 (610) Released config lock.
0
starting pid 636, tty '/dev/ttyS0': '/bin/sh'
@@@@@@@@@@ Before disable SA learning in STAR CPU @@@@@@@@@@
dump 0x70000008
physical addr: 0x70000008 content: 0x00463d96
dump 0x7000000c
physical addr: 0x7000000c content: 0x00463d96
@@@@@@@@@@ After disable SA learning in STAR CPU @@@@@@@@@@
dump 0x70000008
physical addr: 0x70000008 content: 0x004e3d96
dump 0x7000000c
physical addr: 0x7000000c content: 0x004e3d96
open mac port 0
close mac port 0
open mac port 0
device eth0 entered promiscuous mode
1
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
br0 has the IP 192.168.1.226
Disabling SA learning in the STAR internal switch
Configure ethernet port IP to 0.0.0.0
Loaded GPIO driver
registered 0
Num LEDs to init 3
Starting upnpd monitor
15.03
The firmware version is 1.0.00 build 832
WAP610N [UUID 1c9477d4-1dd2-11b2-a242-8db32ac1cc4e] UPNP1.0 Daemon.

/root/mtlk/etc
END CREATE LINKS IN TMP
END MAKE DEVICE PIN
[4294684196] <6>mtlk: Using D-scratchpad for hot context (hw = 784 bytes)
[4294684906] mtlk0 (_mtlk_pci_init_card:1150): PCI: PCI self test status: 0x00000004
[4294687076] <6>mtlk: wlan0 at PCI-0000:00:01.0
cp= 0xc028dcc0 l=256
0000:  fc 1b cd 00 00 00 01 00  80 0d 00 00 00 00 00 00
0010:  30 1a 80 06 00 00 00 00  08 f0 ff ff 08 00 e0 ff
0020:  06 08 7e 00 30 1a 80 06  ff ff ff ff ff ff ff ff
0030:  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff
0040:  c0 00 00 00 00 00 01 03  80 10 b5 41 27 02 44 00
0050:  23 69 7b 11 03 00 00 01  01 08 43 41 00 16 24 09
0060:  0d d0 89 9f 63 dc 8b aa  63 00 01 01 00 00 00 00
0070:  00 00 00 00 34 0b 0a d0  84 a0 5e ee 8c b5 68 00
0080:  00 01 00 00 aa 5d 00 00  00 00 64 0a 86 f5 84 b6
0090:  60 0a 8e be 66 00 01 01  00 00 b3 5d 00 00 00 00
00a0:  84 0c 88 fc 85 bc 5f 19  8f c4 65 00 01 00 00 00
00b0:  b8 5c 00 00 00 00 9d 85  84 12 8f ca 6c 17 95 c6
00c0:  6f 00 00 01 bd 63 ac 5c  00 00 00 00 05 2f 11 d3
00d0:  9e 93 80 a6 99 88 88 00  00 00 7c 6f 73 77 00 00
00e0:  00 00 00 00 00 00 07 6e  10 d6 a1 9d 84 a9 9b 77
00f0:  75 00 00 01 86 72 00 00  00 00 00 00 00 00 00 00
[4294689916] <6>mtlk: Options mask is 0x02
[4294689926] mtlk0 (mtlk_core_start:8080): DFS (SM-required) channels will not be used
[4294689936] <6>mtlk: wlan0 at PCI-0000:00:01.0 with EEPROM MAC-address 00:23:69:7b:11:03
[4294689946] <6>mtlk: EEPROM version = 0x301 (769)
[4294689966] <6>mtlk:
Driver version: 2.3.5.19.6.7048.branches/REL_2.3.5.Release
MAC/PHY versions:
ap_upper.bin: @@@ VERSION INFO @@@ version number: REL_2.3.5_r788 MIPS: Upper CPU(TMC AGG AP) interface: PCI  phy type: real phy on May 12 2009 at 17:53:15@@@ END @@@
contr_lm.bin: @@@ VERSION INFO @@@ version number: REL_2.3.5_r788 MIPS: Lower MAC  interface: --  phy type: real phy on May 12 2009 at 17:52:49@@@ END @@@

/root/mtlk/etc
END INSMOD DRIVER
Configuring Linux QoS Queues
END QOS
008,200
Error : unrecognised wireless request "s:"
Error : unrecognised wireless request "s:"
Error : unrecognised wireless request "s:"
Error : unrecognised wireless request "s:"
DriverSET Param is DONE
END DRIVER PARAMS
END HW LINITS
END WRITE MAC ADDRESS
DFSDisabled=1
Configuring wireless bridging
ifconfig: SIOCSIFFLAGS: Bad address
device wlan0 entered promiscuous mode
Start apps init
1
1
0
chmod: /tmp/config.conf: No such file or directory
grep: /tmp/wsc_config.txt: No such file or directory
/root/mtlk/etc
Finished apps init
call drvhlpr
start drvhlpr with param
Starting BCL Server...
[0030108493] drvhlpr: Metalink Driver Helper (version 1.3.18.exported)
Starting Web Server...
Configuring wireless bridging
drvhlpr uses obsolete (PF_INET,SOCK_PACKET)
[0033255590] drvhlpr: Waiting for kernel messages

starting pid 934, tty '/dev/ttyS0': '/sbin/getty'

#############################################
Welcome to the Metalink Dongle STAR platform,
also known as

   D O R A N G O

(Dongle on Dorado)
#############################################

WAP610N login: br0: port 2(wlan0) entering learning state
br0: topology change detected, propagating
br0: port 2(wlan0) entering forwarding state
mtlk_linkstat_event.sh:Wireless Link is UP
WET610N will roll-back to default IP and netmask setting, IP: 192.168.1.226, netmask: 255.255.255.0
On DHCP startup status, skip to recover IP to default one
delay for autoip ..
delay for autoip ..
Configure IP to 169.254.181.54 ..
Current IP Address is - 192.168.1.226

cat /proc/cpuinfo[edit]

# cat /proc/cpuinfo
Processor       : FA526id(wb) rev 1 (v4l)
BogoMIPS        : 153.19
Features        : swp half
CPU implementer : 0x66
CPU architecture: 4
CPU variant     : 0x0
CPU part        : 0x526
CPU revision    : 1
Cache type      : write-back
Cache clean     : cp15 c7 ops
Cache lockdown  : format B
Cache format    : Harvard
I size          : 16384
I assoc         : 2
I line length   : 16
I sets          : 512
D size          : 16384
D assoc         : 2
D line length   : 16
D sets          : 512

Hardware        : STAR STR9100
Revision        : 0000
Serial          : 0000000000000000

cat /proc/mtd[edit]

# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00400000 00010000 "STR9100 NOR Flash"
mtd1: 00020000 00010000 "ARMBOOT"
mtd2: 003b0000 00010000 "Linux Kernel"
mtd3: 00010000 00010000 "Non-volatile Config Partition"
mtd4: 00010000 00010000 "Config Partition"

cat /proc/bus/pci/devices[edit]

# cat /proc/bus/pci/devices
0000    eeee0000        0       00000000        00000000        00000000        00000000        00000000        00000000        00000000        00000000  00000000 00000000        00000000        00000000        00000000        00000000
0008    1a300680        5       b0a00008        b0800008        00000000        00000000        00000000        00000000        00000000        00001000  00200000 00000000        00000000        00000000        00000000        00000000        mtlk

ps[edit]

# ps
  PID  Uid        VSZ Stat Command
    1 root        940 S   init
    2 root            SWN [ksoftirqd/0]
    3 root            SW< [events/0]
    4 root            SW< [khelper]
    5 root            SW< [kthread]
   12 root            SW< [kblockd/0]
   33 root            SW  [pdflush]
   34 root            SW  [pdflush]
   36 root            SW< [aio/0]
   35 root            SW  [kswapd0]
  552 root            SW< [cqueue/0]
  572 root            SW  [mtdblockd]
  621 root            SW< [loop0]
  694 root        936 S N /bin/sh ./mtlk_upnpd_monitor.sh
  695 root        932 S   /bin/sh ./mtlk_pbc_reboot.sh
  696 root        928 S   cat /dev/gpio3
  894 root       3004 S   ./wsccmd 1 2 3 4
  895 root        936 S   /bin/sh ./WPS_PBC.sh 1 2
  902 root        940 S   /bin/sh /etc/mtlk_init_start.sh
  904 root        784 R N /root/mtlk/bcl/BclSockServer
  906 root        736 S   ./drvhlpr -a eth0 -a eth1 -r 1 -i wlan0
  907 root        736 S   ./drvhlpr -a eth0 -a eth1 -r 1 -i wlan0
  908 root       3004 S   ./wsccmd 1 2 3 4
  910 root       3004 S   ./wsccmd 1 2 3 4
  911 root       3004 S   ./wsccmd 1 2 3 4
  912 root       3004 S   ./wsccmd 1 2 3 4
  913 root        784 S N /root/mtlk/bcl/BclSockServer
  914 root        784 S N /root/mtlk/bcl/BclSockServer
  915 root       1788 S N /root/mtlk/web/webs -c 0
  918 root       3004 S   ./wsccmd 1 2 3 4
  920 root        736 S   ./drvhlpr -a eth0 -a eth1 -r 1 -i wlan0
  921 root        784 R N /root/mtlk/bcl/BclSockServer
  922 root       3004 S   ./wsccmd 1 2 3 4
  923 root       3004 S   ./wsccmd 1 2 3 4
  924 root       3004 S   ./wsccmd 1 2 3 4
  925 root       3004 S   ./wsccmd 1 2 3 4
  927 root        928 S   cat /dev/gpio13
  928 root        736 S   ./drvhlpr -a eth0 -a eth1 -r 1 -i wlan0
  929 root        784 S N /root/mtlk/bcl/BclSockServer
  931 root       2204 S   ./hostapd -t hostapd.conf -ddK
 1038 root        788 S N /bin/autoip br0
 1065 root       1516 S N upnpd
 1068 root        948 S N udhcpc -i br0 -H WAP610N -s /etc/udhcpc/dhcp.tcl -b
 1287 root        944 S   -sh
 1383 root        928 S N sleep 120
 1416 root        936 R   ps