Edimax EW-7206APg v4

From TechInfoDepot
Jump to navigationJump to search
multiple revisions of this device, use caution
bg (G54)
Wireless LAN Access Point IEEE 802.11g/b
Range Extender / Access Point
2-EW-7206APg top 1000X1000.png
Edimax EW-7206APg v4
access point, repeater, bridge
CPU1 Type
Lexra LX5280
CPU1 Speed
180 MHz
Flash1 Chip
Macronix MX29LV160CBTC-70G
Flash1 Size
2 MiB2,097,152 B <br />16,384 Kib <br />2,048 KiB <br />16 Mib <br />0.00195 GiB <br />
RAM1 Size
8 MiB8,388,608 B <br />65,536 Kib <br />8,192 KiB <br />64 Mib <br />0.00781 GiB <br />
RAM1 Chip
Mira P2V64S40ETP-G6
ETH chip1
ETH chip2
Realtek RTL8201CP
Ethernet Port Count

802dot11 OUI: 00:1F:1F (4 E, 14 W)
Ethernet OUI: 00:1F:1F (4 E, 14 W)

Stock bootloader
rtkload v1.3c
Stock FW OS
Expansion IF types
none specified
12 VDC, 1 A
Connector type

Additional chips
2.4GHz Power Amplifier IC;Microchip;SST12LP14A;SST, 12LP14A, 825112;1;InGaP/GaAs;QFN-16;3 mm x 3 mm;


Default SSID: default (101 addl. devices)
Default IP address:
the IP is used by 288 additional devices
of which 58 are Edimax devices
Default login user: admin
Default login password: 1234
admin:1234 credentials used by 181 additional devices
of which 73 are Edimax devices

Availability End of Life
FCC approval date 30 May 2007
Radio 1
Realtek RTL8225
Wireless interface OUI
Antenna Connector Type
Wireless Standard
IEEE 802.11b/g
up to 54 Mbps
up to 11 Mbps
WiFi Operating Frequency
2.4 GHz
 CPU1 brandRadio1 chip1 brandRadio1 chip2 brand
Edimax EW-7206APg v1RealtekRealtek
Edimax EW-7206APg v4RealtekRealtek

For a list of all currently documented Realtek chipsets with specifications, see Realtek.

For a list of all currently documented Edimax device with specifications, see Edimax.

54 Mbps - 2.4GHz 802.11g = G54 class


"1242-00000263-01Z" is silkscreened on the board.

The FCC test report lists the following as identical models..

  • Edimax EW-7206APg / GAP-E06G
  • LevelOne WAP-0006
  • Longshine LCS-WA5-40
  • Hawking HWREG1 / HWBA54G
  • TONZE AW-6200R
  • PheeNet WAP-554G
  • JAHT WP-4001BR
  • Conceptronic C54APM
  • Intellinet 501903
  • Asbis CN-WFAP
  • Sandberg 131-01
  • 2 Direct WL0027
  • Planet WAP-4033
  • Micronet SP918GKV5

JTAG-Serial Info


Info derived from

These serial logs are from the Intellinet branded unit shown above.

boot log

UART1 output test ok
Uart init
mfid=000000c2 devid=00002249
Found 1 x 2M flash memory

---RealTek(RTL8186)at 2005.06.06-11:22+0800 version 1.3c [16bit](180MHz)
Jump to image start=0x80300000...
display on
entering boot loader, turning on display
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
early printk enabled
Determined physical RAM map:
 memory: 00800000 @ 00000000 (usable)
Initial ramdisk at: 0x80196000 (634880 bytes)
On node 0 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram console=0 ramdisk_start=0 single
Calibrating delay loop... 178.99 BogoMIPS
Memory: 5660k/8192k available (1419k kernel code, 2532k reserved, 760k data, 48k init, 0k highmem)
Dentry-cache hash table entries: 1024 (order: 1, 8192 bytes)
Inode-cache hash table entries: 512 (order: 0, 4096 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 2048 (order: 1, 8192 bytes)
check_wait... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
pty: 256 Unix98 ptys configured
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
HDLC line discipline: version $Revision: $, maxframe=4096
N_HDLC line discipline registered.
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 6144K size 1024 blocksize
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
HDLC support module revision 1.02 for Linux 2.4
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Found 1 x 2M Byte MXIC MX29LV160AB at 0xbe000000
RTL8185 driver version 1.11 (2006-08-01)
8186NIC Ethernet driver v0.0.2 (Jan 30, 2004)
eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4
eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
RAMDISK: squashfs filesystem found at block 0
RAMDISK: Loading 618 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 620k freed
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 48k freed
mount /proc file system ok!
serial console detected.  Disabling virtual terminals.

BusyBox v1.00-pre8 (2005.11.23-10:23+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

Sat Jan  1 00:00:00 UTC 2000
create flash.inc
Initialize WLAN interface
Interface doesn't accept private ioctl...
set_mib (89F1): Operation not permitted
SIOCGIFFLAGS: No such device
bridge br0 doesn't exist; can't delete it
Setup bridge...
device eth0 entered promiscuous mode
eth0:phy is 8201
SIOCDELRT: No such process
device wlan0 entered promiscuous mode
SIOCDELRT: No such process
br0: port 2(wlan0) entering listening state
br0: port 1(eth0) entering listening state
br0: port 2(wlan0) entering learning state
br0: port 2(wlan0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
SIOCDELRT: No such process
SIOCDELRT: No such process
********** run Diagd **********
setting: port: 31727
running in daemon mode
********** run GaTest **********
IEEE 802.11f (IAPP) using interface br0 (v1.6)

         Please enter your Name and Password

 User Name   :

<TAB> Select                     <ESC> Exit                     <Enter> Enter


User Images