Sagemcom F@ST 5280
From TechInfoDepot
Jump to navigationJump to searchabgn+ac | |
|---|---|
| AC2650 Wave 2 Dual-Band WiFi Router | |
|
| |
| WikiDevi.wi-cat.ru | |
| Platform | |
| Brand • Model • Rev |
Sagemcom F@ST 5280(RAC2V1S) |
| FCC ID | |
| Type |
wireless router |
| Wireless class |
AC2650 |
| CPU1 |
Broadcom BCM4906 |
| CPU1 Speed |
1.8 GHz ( 4 cores ) |
| Flash1 Type |
NAND |
| Flash1 Chip |
Spansion S34ML02G1 |
| Flash1 Size |
256 MiB268,435,456 B <br />2,097,152 Kib <br />262,144 KiB <br />2,048 Mib <br />0.25 GiB <br /> |
| RAM1 Size |
512 MiB536,870,912 B <br />4,194,304 Kib <br />524,288 KiB <br />4,096 Mib <br />0.5 GiB <br /> |
| RAM1 Chip |
Samsung K4B4G1646E-BYK0 |
| ETH chip1 |
Broadcom BCM4906 |
| Switch |
Broadcom BCM4906 |
| Ethernet Port Count |
1-WAN 4-1GbE-LAN |
|
802dot11 OUI: none specified | |
| Expansion IF types |
USB 3.0 |
| USB ports |
1 |
| USB Hub Compatible |
Untested |
| Power |
12 VDC, 2.5 A |
| Connector type |
barrel |
| Flags |
Wave2, DFS (master) |
| Categorized as |
not categorized |
| Other | |
| Default IP address |
???.???.???.??? |
| Retail | |
| Availability | Spectrum customers only |
| FCC approval date | 26 September 2017 |
| Country of manuf | China |
| Radio 1 | |
| Chip1 |
Broadcom BCM4366E |
| Wireless interface OUI |
none specified |
| Antenna Connector Type |
none specified |
| MIMO status |
4x4:4 |
| Wireless Standard |
IEEE 802.11a/n/ac |
| 802.11ac |
up to 1900 Mbps |
| N-QAM |
up to 750 Mbps |
| 802.11n |
up to 600 Mbps |
| 802.11a |
up to 54 Mbps |
| WiFi Operating Frequency |
5 GHz |
| Radio 2 | |
| Chip1 |
Broadcom BCM4365E |
| Wireless interface OUI |
none specified |
| Antenna Connector Type |
none specified |
| MIMO status |
3x3:3 |
| Wireless Standard |
IEEE 802.11b/g/n |
| N-QAM |
up to 750 Mbps |
| 802.11n |
up to 450 Mbps |
| 802.11g |
up to 54 Mbps |
| 802.11b |
up to 11 Mbps |
| WiFi Operating Frequency |
2.4 GHz |
For a list of all currently documented Broadcom chipsets with specifications, see Broadcom.
Overview
"FAST5280CH/MB REV:1.03A" is silkscreened on the main board.
- Also known as Sagemcom RAC2V1S.
The user manual is branded for Spectrum Cable.
A daughterboard with both Wi-Fi radios connects to the main board using a PCIe x1 slot.
- This daughterboard has "FAST5280CH/WIFI REV:1.04" silkscreened on it.
An FCC filing available 09/19/2017 was requested to be dismissed.
- A new filing was available on 09/26/2017.
Links of Interest
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Upgrading
This section is empty. You can help by adding to it. (July 2020) |
Reverting
This section is empty. You can help by adding to it. (July 2020) |
JTAG-Serial Info
JTAG
This section is empty. You can help by adding to it. (July 2020) |
Serial
Serial Pinouts
This section is empty. You can help by adding to it. (July 2020) |
Boot Log
| This is the boot log (up to U-Boot) obtained via the UART Port (speed 115200)
|
|---|
Version cfe-rom: 0.8.2 FPS0 J2EP Base: 5.2_03 CFE version 1.0.38-161.184 for BCM94908 (64bit,SP,LE) Build Date: vendredi 6 octobre 2017, 18:20:02 (UTC+0200) (g601671@rmm-1186759) Copyright (C) 2000-2015 Broadcom Corporation. Version cfe-ram: 0.8.2 Boot Strap Register: 0x6fd42 Chip ID: BCM4906_A0, Broadcom B53 Quad Core: 1800MHz Total Memory: 536870912 bytes (512MB) NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes NAND flash device: Spansion S34ML02G1, id 0x01da block 128KB size 262144KB pmc_init:PMC using DQM mode pmc_init:7 0 fe1e044f 3520356 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host/tftp (f/h/c) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Default host ramdisk file name : Default ramdisk store address : Default DTB file name : Board Id : F@ST5280 Number of MAC Addresses (1-64) : 10 Base MAC Address : [removed] PSI Size (1-128) KBytes : 128 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Auxillary File System Size Percent: 0 flow memory allocation (MB) : 14 buffer memory allocation (MB) : 16 DHD 0 memory allocation (MB) : 0 DHD 1 memory allocation (MB) : 0 DHD 2 memory allocation (MB) : 0 WLan Feature : 0x00 Partition 1 Size (MB) : Partition 2 Size (MB) : Partition 3 Size (MB) : Partition 4 Size (MB) (Data) : 4MB Initalizing switch low level hardware. Software Resetting Switch ... Done. Waiting MAC port Rx/Tx to be enabled by hardware ...Done Disable Switch All MAC port Rx/Tx Initializing UBI and starting U-Boot... Looking for UBI... Looking for U-Boot... Found valid GSDF Starting U-Boot from UBI at 0x0000000000080000 U-Boot 2017.05@sc-0.14.2 (Oct 06 2017 - 18:00:03 +0200) sc_f5280 CPU: BCM490x Model: Sagemcom F@ST5280 DRAM: 512 MiB NAND: 256 MiB MMC: ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=2", size 8 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 70, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 51/3, WL threshold: 4096, image sequence number: 49925173 ubi0: available PEBs: 0, total reserved PEBs: 70, PEBs reserved for bad PEB handling: 30 Volume bootenv not found! ** Unable to read env from boot:bootenv ** Using default environment In: serial Out: serial Err: serial Version: 2017.05@sc-0.14.2 Board: F@ST5280 Mode: standard ubi0: detaching mtd1 ubi0: mtd1 is detached ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=2", size 8 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 70, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 51/3, WL threshold: 4096, image sequence number: 49925173 ubi0: available PEBs: 0, total reserved PEBs: 70, PEBs reserved for bad PEB handling: 30 Net: brcmenet Autoboot in 0 seconds. Press <SPACE> to abort. |
Serial Recovery
This section is empty. You can help by adding to it. (July 2020) |
USB Info
This section is empty. You can help by adding to it. (July 2020) |
vlan Info
This section is empty. You can help by adding to it. (July 2020) |
Pictures
This section is empty. You can help by adding to it. (July 2020) |
Notes
This device have 2 versions. It's not v2, same model, same fccid, same board revision.
1.BCM4906 + BCM4365E + BCM4366E
2.BCM4906 + BCM43602 + BCM4366E
Hardware Modification
This section is empty. You can help by adding to it. (July 2020) |
See also
- Arris RAC2V1A - Arris TR4400-AC (SerComm)
- Askey RAC2V1K - Askey RT4230W (Askey)
- Sagemcom RAC2V1S - Sagemcom F@ST 5280
- Ubee RAC2V1U - Foxconn U10H128.00 (Spectrum)
- FCC ID: XCNRAC2V1U (2017-06-29) • DVE 12V/2.5A
- Charter RAX1V1K - Askey RT5000W - 802.11ax DBDC Router
- Askey RT4220W • Cube Router - 802.11ac 2x2 Router • PPage
- Askey RT4230W • Puma Router - 802.11ac 4x4 Router • PPage
Categories:
- Sagemcom
- Embedded system/wireless router
- Embedded System Broadcom
- Embedded System BCM4906
- Embedded System BCM4366E
- Has Mimo Status
- Embedded System IEEE 802.11a/n/ac
- Embedded System BCM4365E
- Embedded System IEEE 802.11b/g/n
- Wireless Embedded System
- Dual-Radio Wireless Embedded System
- Dual-Band
- Broadcom
- Embedded System
- Retail Photo's Needed
- User Photo's Needed
- FCC Photo's Needed
- English Documentation