Freecom SilverStore
From TechInfoDepot
Revision as of 02:49, 9 September 2022 by ShadowBot (talk | contribs) (→top: clean up, replaced: 802dot11_prot → 802dot11_protocols, 802dot11_protocolsocols → 802dot11_protocols, 802dot11_prot → 802dot11_protocols, 802dot11_protocolsocols → 802dot11_protocols, |802dot11_protocols =none → |802dot11_protocols = none)
| SilverStore 2 Drive | |
|
| |
| WikiDevi.wi-cat.ru | |
|---|---|
| 3rd Party Firmware | |
| dd-wrt |
Status Unknown |
| OpenWrt |
Status Unknown |
| Tomato any flavor |
Incompatible |
| Gargoyle |
Status Unknown |
| Platform | |
| Brand • Model • Rev |
Freecom SilverStore 2-Drive NAS 1.0 |
| Type |
NAS enclosure |
| CPU1 |
Marvell 88F6283 |
| CPU1 Speed |
1 GHz |
| Flash1 Chip |
Samsung K9F1G08U0D |
| Flash1 Size |
128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> |
| RAM1 Size |
128 MiB134,217,728 B <br />1,048,576 Kib <br />131,072 KiB <br />1,024 Mib <br />0.125 GiB <br /> |
| RAM1 Chip |
Samsung K4B1G1646G-BCH9 |
| ETH chip1 |
Marvell 88F6283 |
| ETH chip2 |
Marvell 88E1318 |
| Ethernet Port Count |
1-1GbE-LAN |
|
| |
| Stock bootloader |
U-Boot 1.1.4 Marvell 3.5.9 |
| Stock FW OS |
Linux 2.6.31.8 |
| Expansion IF types |
USB 3.0, SATA |
| USB ports |
2 |
| SATA Ports |
2 |
| USB Hub Compatible |
Untested |
| Power |
12 VDC, 4 A |
| Connector type |
barrel |
| Serial Port (UART) |
yes, 4-pin header, CN4, (115200 8N1) |
| Flags |
RTC w/ battery backup |
|
Additional chips | |
| Categorized as |
not categorized |
| Other | |
| Default IP address |
192.168.0.1 |
| 3rd Party Firmware Support | |
| Retail | |
| ASIN |
B0060H7DHK |
| Country of manuf | China |
For a list of all currently documented Marvell chipsets with specifications, see Marvell.
Overview
- CPU: Marvell 88F6283 (ARMADA 300) @1GHz
- Stock bootloader is locked to boot only Stock OS by checking signature.
- MB has place for soldering second RAM IC
Links of Interest
This section is empty. You can help by adding to it. (September 2021) |
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Upgrading
This section is empty. You can help by adding to it. (September 2021) |
Reverting
This section is empty. You can help by adding to it. (September 2021) |
JTAG-Serial Info
JTAG
This section is empty. You can help by adding to it. (September 2021) |
Serial
Serial Pinouts
This section is empty. You can help by adding to it. (September 2021) |
Serial Recovery
This section is empty. You can help by adding to it. (September 2021) |
bootloader boot log
| bootloader boot log
|
|---|
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** uboot_ver:v0.0.9 **
** MARVELL BOARD: HNC-N2 LE
U-Boot 1.1.4 (Nov 9 2011 - 17:49:26) Marvell version: 3.5.9
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00
Soc: 88F6282 A1CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM (DDR3) CAS Latency = 6 tRP = 6 tRAS = 15 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
Found ADT7473, program PWM1 ... OK
Flash: 0 kB
Marvell Serial ATA Adapter
Integrated Sata device found
CPU : Marvell Feroceon (Rev 1)
Scanning partition header:
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
PEX 1: interface detected no Link.
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Saving Environment to NAND...
Erasing redundant Nand... 0x000c0000 0x000c0000
Writing to redundant Nand... Erasing Nand...Writing to Nand... done
|
bootloader environment
| bootloader environment
|
|---|
Marvell>> printenv baudrate=115200 loads_echo=0 ipaddr=10.4.52.165 serverip=10.4.52.7 rootpath=/srv/ubuntu netmask=255.255.255.0 run_diag=yes MALLOC_len=1 ethprime=egiga0 bootargs_root=root=/dev/ram0 rootfstype=cramfs init=/etc/rc.preroot initrd=0x800000,0x1000000 bootargs_end=:::DB88FXX81:eth0:none image_name=uImage standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x2000000; lcd0_enable=0 lcd0_params=640x480-16@60 ethaddr=00:50:43:12:29:32 ethmtu=1500 mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500 usb0Mode=host nandEcc=1bit netretry=no rcvrip=169.254.100.100 loadaddr=0x02000000 autoload=no image_multi=yes uboot_ver=v0.0.9 mfgtest_state=final_tested_ok mfgmodel=HNC-N2 ethact=egiga0 stdin=serial stdout=serial stderr=serial mainlineLinux=no enaMonExt=no enaCpuStream=no enaWrAllo=no pexMode=RC disL2Cache=no setL2CacheWT=yes disL2Prefetch=yes enaICPref=yes enaDCPref=yes sata_dma_mode=yes netbsd_en=no vxworks_en=no console=console=ttyS0,115200 mtdparts=nand_mtd:0x000a0000@0x0(uboot),0x00040000@0x000a0000(param),0x00280000@0x000e0000(preroot), 0x00380000@0x00360000(uimage),0x076e0000@0x006e0000(rootfs),0x00240000@0x07dc0000(misc),128m@0x0(flash) bootcmd_f=nand reset; nand read.e 0x800000 0x00100000 0x00199800; check_crc32 PrEr; bootcmd=nand reset; nand read.e 0x800000 0x00100000 0x00199800; check_crc32 PrEr; nand reset; nand read.e 0x40000 0x00380000 0x0027d400; check_crc32 KrNl; setenv bootargs $(console) $(bootargs_root); bootm 0x40000; bootdelay=3 disaMvPnp=no enaAutoRecovery=yes pcieTune=no pcieTune1=no bootcmd="" Environment size: 1411/131067 bytes |
Bootloader
USB Info
This section is empty. You can help by adding to it. (September 2021) |
vlan Info
This section is empty. You can help by adding to it. (September 2021) |
Pictures
This section is empty. You can help by adding to it. (September 2021) |
Notes
This section is empty. You can help by adding to it. (September 2021) |
Hardware Modification
This section is empty. You can help by adding to it. (September 2021) |
See also
This section is empty. You can help by adding to it. (September 2021) |