DBL GoIP-4
From TechInfoDepot
Revision as of 02:31, 9 September 2022 by ShadowBot (talk | contribs) (→top: clean up, replaced: 802dot11_prot → 802dot11_protocols, 802dot11_protocolsocols → 802dot11_protocols, 802dot11_prot → 802dot11_protocols, 802dot11_protocolsocols → 802dot11_protocols, |802dot11_protocols =none → |802dot11_protocols = none)
| GSM VoIP Gateway | |
| Homepage | |
|---|---|
| WikiDevi.wi-cat.ru | |
| Platform | |
| Brand • Model • Rev |
DBL GoIP-4 |
| Type |
GSM VoIP gateway |
| CPU1 |
Marvell 88E6218 |
| CPU1 Speed |
133 MHz |
| Flash1 Chip |
Brand? Model? |
| Flash1 Size |
4 MiB4,194,304 B <br />32,768 Kib <br />4,096 KiB <br />32 Mib <br />0.00391 GiB <br /> |
| RAM1 Size |
16 MiB16,777,216 B <br />131,072 Kib <br />16,384 KiB <br />128 Mib <br />0.0156 GiB <br /> |
| RAM1 Chip |
Brand? Model? |
| ETH chip1 |
Marvell 88E6218 |
| Ethernet Port Count |
1-WAN 1-100MbE-LAN |
|
| |
| Expansion IF types |
none specified |
| Power |
12 VDC, ? A |
| Serial Port (UART) |
yes, 3.3V TTL |
| Flags |
VoIP, GSM |
| Categorized as |
not categorized |
| Other | |
| Default IP address |
???.???.???.??? |
| Retail | |
| ASIN |
B00L11NSXI |
For a list of all currently documented Marvell chipsets with specifications, see Marvell.
Overview
4 internal GSM modems
Links of Interest
This section is empty. You can help by adding to it. (May 2021) |
Flashing
| NOTE: During configuration or flashing a device, the only things that should be hooked to the device is the computer and power. |
Upgrading
This section is empty. You can help by adding to it. (May 2021) |
Reverting
This section is empty. You can help by adding to it. (May 2021) |
JTAG-Serial Info
JTAG
JTAG Pinouts
This section is empty. You can help by adding to it. (May 2021) |
JTAG Recovery
This section is empty. You can help by adding to it. (May 2021) |
Serial
Serial Pinouts
This section is empty. You can help by adding to it. (May 2021) |
Serial Recovery
This section is empty. You can help by adding to it. (May 2021) |
Bootloader (serial)
Initializing... mem: 16M/16 Hit any key for boot setup ARMboot Rev 1.6 for RD-88E62x8 (Jan 18 2007-17:27:34) ARMboot LE version ARMboot code: 00380000 -> 003904c0 ARMboot-> ARMboot-> help go - start application at address 'addr' tftp- boot image via network using TFTP protocol md - memory display mm - memory modify (auto-incrementing) nm - memory modify (constant address) mw - memory write (fill) printenv- print environment variables setenv - set environment variables saveenv - save environment variables to persistent storage defaultenv- get default environment variables reset - Perform RESET of the CPU echo - echo args to console version - print monitor version help - print online help ? - alias for 'help' flash test ARMboot-> printenv bootdelay=5 baudrate=38400 ethaddr=00:40:BC:xx:xx:xx ipaddr=192.168.1.2 serverip=192.168.1.1 gatewayip=192.168.1.254 netmask=255.255.255.0 bootfile=boot.bin sdramImgAddr=0x00100000 flashAddr=0x3FC00000 bootSource=arch Environment size: 219/4092 bytes ARMboot->
Boot (serial)
Initializing...
mem: 16M/16
Hit any key for boot setup
boot kernel: 200000
## Starting application at 0x00200000
Uncompressing Lin... done, booting tinit start
starting rcS...
exec external command: hwinfo
exec external command: insmod
Using /lib/modules/wd.o
mount failed: No such device
exec external command: insmod
Using /lib/modules/unimac.o
syscfg: cannot send to /tmp/.syscfg-server: No such file or directory
exec external command: insmod
Using /lib/modules/gpio_drv.o
starting rc...
Login: exec external command: /sbin/svcd
exec external command: reset_monitor
exec external command: gpio
open gpio fd=8
gpio 9 state=1
exec external command: gpio
open gpio fd=8
gpio 9 state=1
cannot stat /usr/etc/digit_map: No such file or directory
starting httpd...
starting audio...
insmod -x /usr/lib/modules/vpdsp_drv.o freq=96 channels=4
rstn_pin=1 hint_pin=2 ackn_pin=3 afe=4 jb_mode=0 jb_min=60
Using /usr/lib/modules/vpdsp_drv.o
exec external command: gpio
open gpio fd=8
gpio 1 state=1
exec external command: vpdsptool
parse cmd:
type=a04d
length=7
sequence=0
timestamp=0
payload:
#0: e600
#1: 6af7
#2: fff8
#3: dd00
#4: d000
#5: f400
#6: 0100
got command ack: 0000
starting ata...
starting network...
command hostname not found
exec external command: rgcfg
User's Net Config:
VLAN 1 (eth0):
MAC address = 38:3f:10:xx:xx:xx
Port Set = { 0, 1, 5 }
VLAN 2 (eth1):
MAC address = 38:3f:10:xx:xx:xx
Port Set = { 2, 3, 4, 6, 5 }
Switch Information:
Device Name = 88E6218 (Firefox-HG)
Revision = 2
Device Number = 0
Device Enabled = Yes
Base Reg Address = 16
Number of Ports = 7
CPU Port = 5
Init: User network configuration initialized
command 50 not found
starting PC port...
starting telnetd...
exec external command: /usr/sbin/telnetd
starting LAN port...
starting dhcpd...
starting nat...
exec external command: iptables
starting autocfg...
exec external command: /usr/etc/rc.d/init.d/autocfg.start
starting ntp...
starting ipphone...
cannot background builtin commands
Login:
USB Info
This section is empty. You can help by adding to it. (May 2021) |
vlan Info
This section is empty. You can help by adding to it. (May 2021) |
Pictures
This section is empty. You can help by adding to it. (May 2021) |
Notes
This section is empty. You can help by adding to it. (May 2021) |
Hardware Modification
This section is empty. You can help by adding to it. (May 2021) |
See also
This section is empty. You can help by adding to it. (May 2021) |